P A T E N T P U L L Catalog 0305-2 (Revised 10-07-08) General Purpose Regulators R10 / R11 Series 1/4, 3/8 & 1/2 Inch Ports R10 / R11 General Purpose Regulators D Features D • High Flow Performance A Featuring Rugged Design for - + the Most Demanding Applications A • Diaphragm Operated Design with Balanced Poppet Design for Quick and Accurate Regulation C • Accurate Pressure Regulation E C E • Panel Mountable N N B § • High Flow: 1/4" - 80 SCFM B § B 3/8" - 80 SCFM § 1/2" - 100 SCFM R11 R10 • R10: Push-to-Lock, Pull-to-Adjust. Adjusting Lock is engaged when Knob is Removed Rendering Unit Tamper Resistant • R11: Heavy Duty Tee Handle Adjustment Port R10 Regulator Dimensions R10 NPT R11 NPT Size A B C D E N Relieving Relieving R10 Without Gauge 0-125 PSIG Reduced Pressure 2.25 1.40 3.38 2.33 4.78 1.38 (57) (36) (86) (59) (121) (35) 1/4" R10-02C R11-02C R11 3/8" R10-03C R11-03C 2.25 1.40 4.72 2.33 6.13 1.38 1/2" R10-04C R11-04C (57) (36) (120) (59) (156) (35) With Gauge 0-125 PSIG Reduced Pressure inches (mm) 1/4" R10-02CG R11-02CG NOTE: 1.75 Dia. (44mm) hole required for panel 3/8" R10-03CG R11-03CG mounting. 1/2" R10-04CG R11-04CG Bold items are most popular. For other models refer to ordering information below. § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow secondary setting, and 20 PSIG pressure drop. Ordering Information R 10 — 02 C /** Series Port Threads Port Size Reduced Engineering Options Pressure Range Change Designator — NPT 10 Tamper Resistant, 02 1/4 Inch G Gauge Snap Lock, Will be entered at G BSPP 03 3/8 Inch A 0-25 PSIG K Non-Relieving Removable Knob factory. B 0-60 PSIG 04 1/2 Inch P Panel Mount Nut 11 Tee Handle C 0-125 PSIG X64** Fluorocarbon Adjustment *NOTE: Beginning January D 0-250 PSIG O-Rings and 2008, Brass Bottom Plug Diaphragm is Optional - Nylon is N Panel Mount Standard. Threads at Top of ** Brass Bottom Plug Bonnet (R11 Only) Standard with X64, X81, X81** Brass Body and X8 Options. X8** Low Temp. Version X7* Brass Bottom Plug BOLD ITEMS ARE MOST POPULAR. Pneumatic Division B24 Richland, Michigan www.wattsfluidair.com L O C K 39 5 6 5 4 7 Catalog 0305- R36, R37 Series Miniature R364, R374 Series 1/8 & 1/4 Inch Ports R364, R374 Regulators – Miniature A Features • High Flow and High Sensitivity • Constant Bleed Option for Semi-Precision B Applications • Can be Used for Water Service (Non-Relieving) • Unbalanced Poppet Standard • Diaphragm Operated for Fast Response • Non-rising Adjusting Knob C 1/8" NPT • Stainless Steel Version Available E Gauge Ports (See Stainless Steel Section of Catalog) (2) § • High Flow: 10 SCFM (Air) 1.5 GPM (Water) D C Port Size NPT R364, R374  Brass Regulator  Dimensions 1/8" R364-01C A B C 1/" R364-02C 1.56 1.56 .56 Aluminum (39.7) (39.7) (65.1) 1/8" R374-01C D E 0.50 3.06 1/" R374-02C (1.7) (77.8) Bold Items are Most Popular.  Inches (mm) For other models refer to ordering information below. NOTE: 1.50 Dia. (31.8mm) hole required for panel mounting. § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow secondary setting and 5% pressure drop. Ordering Information   R  364  —  01  C  G      /** Engineering  Change  Series Port  Reduced  Options Pressure Preset  Designator Threads Pressure  Options  R364  Brass   G  Gauge Range Will be entered   —  NPT  Blank  No Options  R374  Aluminum K Non-Relieving † at factory. A  0-25 PSIG G BSPP L Preset Non- P Panel Mount Nut   B  0-60 PSIG Adjustable T Tamperproof Preset / Pressure  †   C  0-125 PSIG P Preset Adj. X6 Fluorocarbon O-Rings Limited † Q Preset and Diaphragm  Blank  None Port  Tamperproof X Constant Bleed XXX* Preset Size Adjustable Innervalve Pressure † S Pressure 01  1/8 Inch X1 High Flow Innervalve XXX* Pressure Limiter Max.  02  1/4 Inch X10 Max. Pressure Limiting Limited Adjustable Adjusting Screw † T Pressure * Available Preset / X8 Brass Spring Cage / Pressure Limited Range, Limiter Max. Adjusting Screw 10 to 90 PSIG in 5 PSIG Non- Adj. increments. For higher pressures, contact factory. † Inlet Pressure is 100 PSIG. For (Example: 065 = 65 PSIG) BOLD ITEMS ARE MOST POPULAR. other pressures, contact factory. Pneumatic Division C Richland, Michigan www.wattsfluidair.com Catalog 0305- R36, R37 Series Technical Specifications – R364, R374 Miniature Regulators Technical Information Flow Characteristics Flow Characteristics R364 / R374 (Air) R364 / R374 (Water) 100 100 100 PSIG (6.9 bar Primary Pressure 90 6 100 PSIG (6.9 bar Primary Pressure 6 80 80 5 5 70  60  60 50 3 3 0 0  30  0 0 1 1 10 0 0 0 0 0   6 8 10 1 1 16 18 0 0 1  3  5 Air Flow - SCFM Water Flow - GPM 0 .1 .3 .5 .7 .9 1.1 1.3 0 5 10 15 3 Air Flow - dm /s Water Flow - lpm  n C ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. R364, R374 Regulator Kits & Accessories Specifications Gauges – 1-1/" Dial Size, 1/8" Back Connection Gauge Ports (2) .....................................................................1/8 Inch 0 to 60 PSIG (0 to 00 kPa) ....................... K515N18060 Port Threads ...................................................................1/8, 1/ Inch 1-1/" Dial Size, 1/8" Back Connection Primary Pressure Rating ...................  to 15 PSIG (-15 to 8.5 bar) 0 to 160 PSIG, (0 to 1100 kPa) .................. K515N18160 Supply Pressure ...............................300 PSIG Maximum (0. bar) Mounting Bracket Kit ...................................................... SA161X57 Temperature Rating ...........................0°F to 15°F (.°C to 5°C) (Includes Panel Mount Nut) Weight –  Brass Body ...................................... 0.5 lb. (0.3 kg) / Unit Panel Mount Nut – Plastic ................................................R05X51-P 5 lb. (11.3 kg) / 8-Unit Master Pack Aluminum ...........................................R05X51-A Aluminum Body ............................. 0.5 lb. (0.11 kg) / Unit Spring Cage & Knob ......................................................... CKR36Y 15 lb. (6.80 kg) / 8-Unit Master Pack Spring Cage Kit (Tamperproof) ........................................CKR36T Materials of Construction Repair Kits –    Standard Nitrile Adjusting Screw ....................................................................... Steel Non-Relieving Diaphragm, Valve Assembly ................... RKR163Y Body –  R36 ............................................................................. Brass Relieving Diaphragm, Valve Assembly ............................ RKR16Y R37 ...................................................................... Aluminum   Flourocarbon Springs – Adjusting .................................................................... Steel Non-Relieving Diaphragm, Valve Assembly ............. RKR16KX6 Bottom ........................................................ Stainless Steel Relieving Diaphragm, Valve Assembly ........................ RKR16X6 Spring Cage ............................................................................ Acetal Bottom Plug, Innervalve, Diaphragm Buttom ....................... Brass Pneumatic Division C5 Richland, Michigan www.wattsfluidair.com Pressure Drop - bar Pressure Drop - PSIG Reduced Pressure - bar Reduced Pressure - PSIG Catalog 0305- R35, R36 Series Miniature R354, R364 Series 1/4 Inch Ports R354, R364 Regulator – Miniature Features A • Stainless Steel Construction Handles Dia. Most Corrosive Environments A Dia. • Large Diaphragm to Valve Area Ratio for Precise Regulation and High Flow Capacity • Meets NACE Specifications MR-01-75/ISO 15156 § • High Flow: 1/" – 1 SCFM C1 C E1 E D D R354 R364 R364 R354 Adjustment  Port R354, R364 Regulator  Series NPT BSPP Size Type Dimensions R36 Knob 1/" R36G0CSS R364-02CSS A C C1 1.56 .00 .56 D R35 All Metal 1/" R35G0CSS R354-02CSS (0) (51) (65) Standard part numbers shown bold. For other models refer to ordering  D E E1 information below. 0.50 .50 3.06 § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow (13) (6) (78) secondary setting and 15 PSIG pressure drop. inches (mm) NOTE: 1.5 Dia. (3mm) hole required for panel mounting. ! WARNING Product rupture can cause serious injury. Do not connect regulator to bottled gas. Do not exceed maximum primary pressure rating. Ordering Information   R364  —  02  C    SS Port Type Port Size Pressure Range Options Material Series   –  NPT  02  1/4 Inch A 0-5 PSIG   Blank  Relieving   SS  Stainless Steel   R354  Stainless Steel (0-1.7 bar) G BSPP K Non-   R364  Standard Knob B 0-60 PSIG Relieving (0-.1 bar) P Panel C  0-125 PSIG   Mount Nut     (0-8.5 bar) BOLD ITEMS ARE MOST POPULAR. Pneumatic Division D10 Richland, Michigan www.wattsfluidair.com Catalog 0305- R35, R36 Series Technical Specifications – R354, R364 Air Line Regulators With the adjusting knob (A) turned fully counter-clockwise (no Operation spring load), and pressure supplied to the regulator inlet port, the valve poppet assembly (B) is closed. Turning the adjusting knob clockwise applies a load to control spring (C). This load causes the diaphragm (D) and the valve poppet assembly (B) to move downward allowing flow across the seat area (E) created between the poppet assembly and the seat. Pressure A in the downstream line is sensed below the diaphragm (D) and H offsets the load of spring (C). As downstream pressure rises, poppet assembly (B) and diaphragm (D) move upward until the C C A area (E) is closed and the load of the spring (C) and pressure H under diaphragm (D) are in balance. A reduced outlet pressure D D has now been obtained, depending on spring load. Creating F F a demand downstream, such as opening a valve, results in B B a reduced pressure under the diaphragm (D). The load of E E control spring (C) now causes the poppet assembly to move downward opening seat area (E) allowing air to flow to meet the downstream demand. The flow of downstream air is metered by the amount of opening (E). Should downstream pressure exceed the desired regulated R354 R364 pressure, the excess pressure will cause the diaphragm (D) to move upward against control spring (C), open vent hole (F), and vent the excess pressure to atmosphere through the hole in the bonnet (H). (This occurs in the relieving type regulator only.) Technical Information Flow Characteristics 100 90 1/4 Inch Ports CAUTION: 6 100 PSIG (6.9 bar Primary Pressure 80 REGULATOR PRESSURE ADJUSTMENT –   5 70 The working range of knob adjustment is designed to permit outlet pressures within their full range. Pressure adjustment 4 60 beyond this range is also possible because the knob is not a 50 3 limiting device. This is a common characteristic of most industrial D 40 regulators, and limiting devices may be obtained only by special 2 30 design. 20 1 For best performance, regulated pressure should always be set 10 0 by increasing the pressure up to the desired setting. 0 0 2 4 6 8 10 12 14 16 18 20 Flow - SCFM 0 .1 .3 .5 .7 .9 1.1 1.3 3 Flow - dm /s n Port Threads ..........................................................................1/ Inch R354, R364 Regulator Kits & Accessories Pressure & Temperature Ratings –  R354 Bonnet Kit ............................................................CKR35YSS R35 ....................................................... 300 PSIG Max (0.7 bar) R364 Bonnet Kit (Knob Included) ...............................CKR36YSS 0°F to 180°F (-18°C to 8°C) Gauge (Stainless) – R36 ....................................................... 300 PSIG Max (0.7 bar) 160 PSIG (0 to 1100 kPa), 1-1/" Face ................K515N1160SS 0°F to 150°F (-18°C to 66°C) Panel Mount Bracket (Stainless) .................................... 161X57-SS Note: Air must be dry enough to avoid ice formation at         temperatures below 32°F (0°C).   Panel Mount Nut –    Stainless ...................................................................... R05X51-SS Weight ........................................................................0.5 lb. (0.3 kg) Plastic ..............................................................................R05X51-P Materials of Construction Pipe Nipple –     1/" 316 Stainless Steel ................................................ 616Y8-SS Adjustment Mechanism / Springs .....................316 Stainless Steel Adjusting Knob (R354) ........................................316 Stainless Steel Service Kit –    Relieving .....................................................................RKR36YSS Adjusting Knob (R364) ...............................................Polypropylene Non-Relieving ........................................................... RKR36KYSS Body .....................................................................316 Stainless Steel Springs –  Bonnet (R354) .....................................................316 Stainless Steel   0-5 PSIG Range .....................................................SPR-375--SS Bonnet (R364) ......................................................................... Acetal 0-60 PSIG Range .....................................................SPR-376-1-SS 0-15 PSIG Range ...................................................SPR-377-1-SS Bottom Plug ........................................................316 Stainless Steel Poppet .................................................................316 Stainless Steel Specifications Seals ............................................................................. Fluorocarbon Gauge Port .............................................................................1/ Inch Operation ....................................................Fluorocarbon Diaphragm Pneumatic Division D11 Richland, Michigan www.wattsfluidair.com Pressure Drop - bar Pressure Drop - PSIG Catalog 0305- R35, R36 Series Miniature R354, R364 Series 1/4 Inch Ports R354, R364 Regulator – Miniature Features A • Stainless Steel Construction Handles Dia. Most Corrosive Environments A Dia. • Large Diaphragm to Valve Area Ratio for Precise Regulation and High Flow Capacity • Meets NACE Specifications MR-01-75/ISO 15156 § • High Flow: 1/" – 1 SCFM C1 C E1 E D D R354 R364 R364 R354 Adjustment  Port R354, R364 Regulator  Series NPT BSPP Size Type Dimensions R36 Knob 1/" R36G0CSS R364-02CSS A C C1 1.56 .00 .56 D R35 All Metal 1/" R35G0CSS R354-02CSS (0) (51) (65) Standard part numbers shown bold. For other models refer to ordering  D E E1 information below. 0.50 .50 3.06 § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow (13) (6) (78) secondary setting and 15 PSIG pressure drop. inches (mm) NOTE: 1.5 Dia. (3mm) hole required for panel mounting. ! WARNING Product rupture can cause serious injury. Do not connect regulator to bottled gas. Do not exceed maximum primary pressure rating. Ordering Information   R364  —  02  C    SS Port Type Port Size Pressure Range Options Material Series   –  NPT  02  1/4 Inch A 0-5 PSIG   Blank  Relieving   SS  Stainless Steel   R354  Stainless Steel (0-1.7 bar) G BSPP K Non-   R364  Standard Knob B 0-60 PSIG Relieving (0-.1 bar) P Panel C  0-125 PSIG   Mount Nut     (0-8.5 bar) BOLD ITEMS ARE MOST POPULAR. Pneumatic Division D10 Richland, Michigan www.wattsfluidair.com Catalog 0305- R35, R36 Series Technical Specifications – R354, R364 Air Line Regulators With the adjusting knob (A) turned fully counter-clockwise (no Operation spring load), and pressure supplied to the regulator inlet port, the valve poppet assembly (B) is closed. Turning the adjusting knob clockwise applies a load to control spring (C). This load causes the diaphragm (D) and the valve poppet assembly (B) to move downward allowing flow across the seat area (E) created between the poppet assembly and the seat. Pressure A in the downstream line is sensed below the diaphragm (D) and H offsets the load of spring (C). As downstream pressure rises, poppet assembly (B) and diaphragm (D) move upward until the C C A area (E) is closed and the load of the spring (C) and pressure H under diaphragm (D) are in balance. A reduced outlet pressure D D has now been obtained, depending on spring load. Creating F F a demand downstream, such as opening a valve, results in B B a reduced pressure under the diaphragm (D). The load of E E control spring (C) now causes the poppet assembly to move downward opening seat area (E) allowing air to flow to meet the downstream demand. The flow of downstream air is metered by the amount of opening (E). Should downstream pressure exceed the desired regulated R354 R364 pressure, the excess pressure will cause the diaphragm (D) to move upward against control spring (C), open vent hole (F), and vent the excess pressure to atmosphere through the hole in the bonnet (H). (This occurs in the relieving type regulator only.) Technical Information Flow Characteristics 100 90 1/4 Inch Ports CAUTION: 6 100 PSIG (6.9 bar Primary Pressure 80 REGULATOR PRESSURE ADJUSTMENT –   5 70 The working range of knob adjustment is designed to permit outlet pressures within their full range. Pressure adjustment 4 60 beyond this range is also possible because the knob is not a 50 3 limiting device. This is a common characteristic of most industrial D 40 regulators, and limiting devices may be obtained only by special 2 30 design. 20 1 For best performance, regulated pressure should always be set 10 0 by increasing the pressure up to the desired setting. 0 0 2 4 6 8 10 12 14 16 18 20 Flow - SCFM 0 .1 .3 .5 .7 .9 1.1 1.3 3 Flow - dm /s n Port Threads ..........................................................................1/ Inch R354, R364 Regulator Kits & Accessories Pressure & Temperature Ratings –  R354 Bonnet Kit ............................................................CKR35YSS R35 ....................................................... 300 PSIG Max (0.7 bar) R364 Bonnet Kit (Knob Included) ...............................CKR36YSS 0°F to 180°F (-18°C to 8°C) Gauge (Stainless) – R36 ....................................................... 300 PSIG Max (0.7 bar) 160 PSIG (0 to 1100 kPa), 1-1/" Face ................K515N1160SS 0°F to 150°F (-18°C to 66°C) Panel Mount Bracket (Stainless) .................................... 161X57-SS Note: Air must be dry enough to avoid ice formation at         temperatures below 32°F (0°C).   Panel Mount Nut –    Stainless ...................................................................... R05X51-SS Weight ........................................................................0.5 lb. (0.3 kg) Plastic ..............................................................................R05X51-P Materials of Construction Pipe Nipple –     1/" 316 Stainless Steel ................................................ 616Y8-SS Adjustment Mechanism / Springs .....................316 Stainless Steel Adjusting Knob (R354) ........................................316 Stainless Steel Service Kit –    Relieving .....................................................................RKR36YSS Adjusting Knob (R364) ...............................................Polypropylene Non-Relieving ........................................................... RKR36KYSS Body .....................................................................316 Stainless Steel Springs –  Bonnet (R354) .....................................................316 Stainless Steel   0-5 PSIG Range .....................................................SPR-375--SS Bonnet (R364) ......................................................................... Acetal 0-60 PSIG Range .....................................................SPR-376-1-SS 0-15 PSIG Range ...................................................SPR-377-1-SS Bottom Plug ........................................................316 Stainless Steel Poppet .................................................................316 Stainless Steel Specifications Seals ............................................................................. Fluorocarbon Gauge Port .............................................................................1/ Inch Operation ....................................................Fluorocarbon Diaphragm Pneumatic Division D11 Richland, Michigan www.wattsfluidair.com Pressure Drop - bar Pressure Drop - PSIG P U S H T Catalog 0305- QUBE 55 Series Regulators Hi-Flow R255 Series 3/4 & 1 Inch Ports R255 Regulators – Hi-Flow A Features • Port Blocks (PB) Available to Provide 1-1/" Port Extension to 1" Ported Bodies A (PB) • Self Relieving Feature Plus Balanced Poppet A Provides Quick Response and Accurate Pressure Regulation • Solid Control Piston for Extended Life B § • High Flow: 3/" - 00 SCFM § 1" - 300 SCFM 1/4" NPT C Gauge Ports E (2) D Port NPT R255 Regulator Dimensions Size Without Gauge  A  A (PB) B C D E 3.6 5.91 3.6 6.38 .08 8.6 3/" R255-06C (9) (150) (9) (16) (53) (15) 1" R255-08C Inches (mm) Bold Items are Most Popular.  For other models refer to ordering information below. § SCFM = Standard Cubic Feet Per Minute at 100 PSIG Inlet, 75 PSIG No Flow Secondary Setting, and 10 PSIG Pressure Drop. Ordering Information   R255  —  08  C  /** Thread Type Port Size Pressure Range Engineering Change  Designator — NPT Thread 06 3/" Port C 0 to 15 PSI Will be entered at (For BSPP 08 1" Port factory. threads, use Port Block kit) BOLD ITEMS ARE MOST POPULAR. Pneumatic Division A8 Richland, Michigan www.wattsfluidair.com O L O C K Catalog 0305- QUBE 55 Series Technical Specifications – R255 Regulators Technical Information Relief and Flow Characteristics Relief and Flow Characteristics R255 R255 120 120 8 8 A 3/4 Inch Ports 1 Inch Ports 105 105 Primary Pressure 100 PSIG (6.9 bar) 7 7 Primary Pressure 100 PSIG (6.9 bar) 90 90 6 6 75 75 5 5 60 60 4 4 3 45 45 3 2 30 2 30 1 15 15 1 0 0 0 0 -100 0 100 200 300 400 500 600 -100 0 100 200 300 400 500 600 700 Flow - SCFM Flow - SCFM -50 0 50 100 150 200 250 300 -50 0 50 100 150 200 250 3 3 Flow - dm /s Flow - dm /s n n ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. R255 Regulator Kits & Accessories Specifications Gauges – Gauge Ports ................................................................ Two Ports 1/" 60 PSIG (0 to .1 bar) .............................................. K50N1060 (Can be used as additional High Flow 1/ Inch Outlet Ports) 160 PSIG (0 to 11.0 bar) .......................................... K50N1160 Port Threads ...........................................................................3/", 1" 300 PSIG (0 to 0.7 bar) .......................................... K50N1300 Primary Pressure Rating – Service Kit – Maximum Primary Pressure ............................ 50 PSIG (17. bar) Relieving ..................................................................... P3NKA00RR Temperature Rating ..............................3°F to 175°F (0°C to 80°C) Non-Relieving ............................................................. P3NKA00RN Weight –  Springs –   3/ Inch ....................................................................... lb. (1.9 kg) 1 to 60 PSIG Range ....................................................... C10A130 1 Inch .......................................................................... lb. (1.9 kg)  to 15 PSIG Range ..................................................... C10A1308 5 to 50 PSIG Range ..................................................... C10A1317 Materials of Construction Mounting Bracket Kit .................................................. P3NKA00MW Adjusting Stem ......................................................................... Steel Port Block Kit (1-1/" NPT Ports) ..................................P3NKB9BCL Body .....................................................................................Aluminum Bonnet ................................................................................Aluminum Knob ........................................................................................Plastic Piston .......................................................................................Plastic Poppet Assembly ..................................................................... Brass Seals .......................................................................................... Nitrile Springs: Poppet & Control ......................................................... Steel Pneumatic Division A9 Richland, Michigan www.wattsfluidair.com Pressure Drop - bar Pressure Drop - PSIG Pressure Drop - bar Pressure Drop - PSIG Catalog 0305- Precision Regulators R210 / R220 Series 1/4 Inch Ports R210 / R220 High Precision Regulator Features • Accurate Pressure Regulation Controls Output Pressure to within 0.1% Accuracy B • Multi-Stage Regulation for Maximum Control and Stability • Two Full Flow Gauge Ports • Super Sensitive Relief. Downstream Pressure B Buildup, Down to 0.005 PSIG Above the Set Pressure, is Automatically Vented through Internal Relief Valve 1/4" NPT C Gauge Ports • R0 has High Exhaust Relief Capacity E (2) D A R210 / R220 Regulator Dimensions A B C D .06 .35 3.8 0.53 The R10 / R0 are high precision, Applications    (5) (110) (97) (13.5) multi-stage pressure regulators. The R10 and R0 regulators inches This pressure controller provides the are well suited for any process that (mm) highest level of regulation accuracy and requires very precise regulation of air repeatability available and is ideal for pressure in pipes and vessels. These applications that call for the utmost in regulators are often used, but not control and maximum stability under limited to the following applications: variable operating conditions. • Air Gauging A stainless steel measuring capsule is • Gas Mixing used as a sensing element to activate the high gain servo balanced control • Calibration Standards mechanism in which the main valve is • Air Hoists controlled by a pilot valve. This allows • Web Tensioning for greater accuracy and eliminates many of the problems associated with • Gate Actuators conventional regulators using range • Roll Loading springs and diaphragms. • Valve Operators • Cylinder Loading Ordering Information Reduced Pressure Range (PSIG) Relieving 2 to 40 2 to 120 2 to 120 High Relief In / Out Ports 1/" R10-0A R10-0C R0-0C Pneumatic Division B6 Richland, Michigan www.wattsfluidair.com Catalog 0305- R10 / R0 Series Technical Specifications – R210 / R220 High Precision Regulators Technical Information  to 10 PSIG Range Supply 90 PSIG 50.1 9.9 9.7 0   6 8 10  to 0 PSIG Range Supply 90 PSIG 10.1 9.9 B 9.7 0   6 8 10 Flow SCFM .5 Dia. Thru (11) ! .93 WARNING () .16 Product rupture can cause serious injury. (55) Do not connect regulator to bottled gas. 90˚ .075 Do not exceed maximum primary pressure rating. (1.90) .93 .66 Dia. Thru () (6.8)   ! CAUTION: 1.85 () Places (7) REGULATOR PRESSURE ADJUSTMENT – The working range 1.5 of knob adjustment is designed to permit outlet pressures within (3) .63 their full range. Pressure adjustment beyond this range is also (16) possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting .59 (15) devices may be obtained only by special design. 1.19 For best performance, regulated pressure should always be set (30) by increasing the pressure up to the desired setting. Mounting Bracket: 446-707-045 Operating Pressure Range:  PSIG  bar R210 / R220 Regulator Kits & Accessories PRIMARY – Maximum 150 10.3 Mounting Bracket Kits –  Pipe Mounting (Pair) ....................................................SA00YW57 SECONDARY – Spring Pressure Right Angle Mounting .................................................. 6-707-05   40 PSIG  Minimum  0.1        Maximum 0 .76 Service Kits – -0 PSIG ....................................................................... RKR10A*   120 PSIG  Minimum  0.1 -10 PSIG .....................................................................RKR10C*        Maximum 10 8.7 -10 PSIG (High Relieving) ..........................................RKR0C* Operating Temperature Range .......-18°C * to 65°C (0°F* to 150°F) * Parts in Kit: Diaphragms, Gasket, Bleed Orifice * Temperatures below 0°C (3°F) require moisture free air. Specifications Repeatability / Sensitivity ......................... 0.005 PSIG (0.0003 bar) Inches of Water Column = 1/8" 3 Constant Bleed Rate ...................Less than 0.08 SCFM (0.15m /hr) (Equals Bleed Rate plus other consumption) Weight ........................................................................ 1. lb (0.6 kg) 3 Total Air Consumption .....................................6 SCFH (0.1m /hr.) Materials of Construction Effect of Supply Pressure Variation of 25 PSIG (1.7 bar) on Outlet: Adjusting Stem & Capsule ......................................Stainless Steel Less than 0.005 PSIG (0.0003 bar) Body ............................................................................................Zinc Exhaust (Relief) Capacity – Control Knob .......................................................................... Plastic At 5 PSIG (0.3 bar) above 0 PSIG (1.38 bar) Setpoint 3     Standard Model ........................................... 3 SCFM (3.m /hr) Diaphragm(s) ........................................................................Buna-N 3     High-Relief Model ...................................... 11 SCFM (17m /hr) Seals ......................................................................................Buna-N Flow Capacity – Springs ......................................................................Stainless Steel At 100 PSIG (6.89 bar) Supply, 3 0 PSIG (1.38 bar) Outlet ............................. 1 SCFM (5m /hr) Valve Poppet .............................................................Stainless Steel Gauge Ports .....................................................................1/" NPTF (Can be used as additional full flow 1/" outlet ports) Pneumatic Division B7 Richland, Michigan www.wattsfluidair.com Output PSIG Catalog 0305- Precision Regulators R216 Series 1/4 & 3/8 Inch Ports R216 Precision Regulators Features • High Flow Performance Featuring Rugged Design for the Most Demanding Applications • Ideal for Those Installations Calling for Constant Pressure with Wide Variation A, C, in Flow & D • Diaphragm Operated with Large Surface B Area and Aspirator for Quick and Precise Regulation 0.688 Dia. 17,5 Ø Max. Panel • Heavy Duty Tee Handle Adjustment Thickness .5 (6,) • Panel Mount Version Available § • High Flow: 1/" & 3/8" - 0 SCFM E N B 1/8" Gauge Port Port  NPT BSPP R216 Regulator Dimensions Size Relieving Relieving A B C D E N Tee Handle, Without Gauge 0-20 PSIG Reduced Pressure R216-02F, R216-03F 1/" R216-02F R16G0F .5 1. .5 .5 .78 0.85 (108) (31.6) (108) (108) (11) (1.5) 3/8" R16G03F R216-03F R216-02FP, R216-03FP Hand Wheel Knob, Without Gauge 0-20 PSIG Reduced Pressure .5 1. .5 .5 .78 0.85 1/" R216-02FP R16G0FP (108) (31.6) (108) (108) (11) (1.5) 3/8" R216-03FP R16G03FP inches (mm) Bold Items are Most Popular.  For other models refer to ordering information below. § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow secondary setting, and 0 PSIG pressure drop. Ordering Information   R  216  —  02  F    /** Port Threads Port Size Reduced  Options Engineering  Pressure Range Change Designator   —  NPT  02  1/4 Inch K Non-Relieving E 0-8 PSIG G BSPP  03  3/8 Inch P Panel Mount with Knob Will be entered at factory.   F  0-20 PSIG H 0-50 PSIG BOLD ITEMS ARE MOST POPULAR. Pneumatic Division B Richland, Michigan www.wattsfluidair.com Catalog 0305- R16 Series Technical Specifications – R216 Precision Regulators Technical Information Flow Characteristics R216 30 .0 5 1.5 0 1/4 & 3/8 Inch Ports 100 PSIG (6.9 bar) Primary Pressure 15 1.0 B 10 0.5 5 0 0 0 5 10 15 0 5 30 35 0 5 Flow - SCFM 0   6 8 10 1 1 16 18 0 3 Flow - dm /s n ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. R216 Regulator Kits & Accessories Specifications Round Plastic Knob ............................................................. 118Y51 Gauge Port (1) .......................................................................1/8 Inch Panel Mount Conversion Kit  Port Threads ...................................................................1/, 3/8 Inch   (Spring Cage, Knob, Hardware) ........................................... 06 Reduced Pressure Range  ................. 5 to 0 PSIG (0.03 to 1. bar) Repair Kits – Supply Pressure ...............................300 PSIG Maximum (0. bar) Non-Relieving Diaphragm, Temperature Rating ...........................0°F to 15°F (.°C to 5°C) Valve Assembly (1/", 3/8") .............................................RK16KY Weight .............................................................. . lb. (1.00 kg) / Unit Relieving Diaphragm, 18 lb. (8.16 kg) / 8-Unit Master Pack Valve Assembly (1/", 3/8") ............................................... RK16Y Materials of Construction Body, Spring Cage ......................................................................Zinc Bottom Plug ............................................................................. Brass Seals ...................................................................................... Buna N Pneumatic Division B5 Richland, Michigan www.wattsfluidair.com Secondary Pressure - bar Secondary Pressure - PSIG Catalog 0305- Precision Regulators R210 / R220 Series 1/4 Inch Ports R210 / R220 High Precision Regulator Features • Accurate Pressure Regulation Controls Output Pressure to within 0.1% Accuracy B • Multi-Stage Regulation for Maximum Control and Stability • Two Full Flow Gauge Ports • Super Sensitive Relief. Downstream Pressure B Buildup, Down to 0.005 PSIG Above the Set Pressure, is Automatically Vented through Internal Relief Valve 1/4" NPT C Gauge Ports • R0 has High Exhaust Relief Capacity E (2) D A R210 / R220 Regulator Dimensions A B C D .06 .35 3.8 0.53 The R10 / R0 are high precision, Applications    (5) (110) (97) (13.5) multi-stage pressure regulators. The R10 and R0 regulators inches This pressure controller provides the are well suited for any process that (mm) highest level of regulation accuracy and requires very precise regulation of air repeatability available and is ideal for pressure in pipes and vessels. These applications that call for the utmost in regulators are often used, but not control and maximum stability under limited to the following applications: variable operating conditions. • Air Gauging A stainless steel measuring capsule is • Gas Mixing used as a sensing element to activate the high gain servo balanced control • Calibration Standards mechanism in which the main valve is • Air Hoists controlled by a pilot valve. This allows • Web Tensioning for greater accuracy and eliminates many of the problems associated with • Gate Actuators conventional regulators using range • Roll Loading springs and diaphragms. • Valve Operators • Cylinder Loading Ordering Information Reduced Pressure Range (PSIG) Relieving 2 to 40 2 to 120 2 to 120 High Relief In / Out Ports 1/" R10-0A R10-0C R0-0C Pneumatic Division B6 Richland, Michigan www.wattsfluidair.com Catalog 0305- R10 / R0 Series Technical Specifications – R210 / R220 High Precision Regulators Technical Information  to 10 PSIG Range Supply 90 PSIG 50.1 9.9 9.7 0   6 8 10  to 0 PSIG Range Supply 90 PSIG 10.1 9.9 B 9.7 0   6 8 10 Flow SCFM .5 Dia. Thru (11) ! .93 WARNING () .16 Product rupture can cause serious injury. (55) Do not connect regulator to bottled gas. 90˚ .075 Do not exceed maximum primary pressure rating. (1.90) .93 .66 Dia. Thru () (6.8)   ! CAUTION: 1.85 () Places (7) REGULATOR PRESSURE ADJUSTMENT – The working range 1.5 of knob adjustment is designed to permit outlet pressures within (3) .63 their full range. Pressure adjustment beyond this range is also (16) possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting .59 (15) devices may be obtained only by special design. 1.19 For best performance, regulated pressure should always be set (30) by increasing the pressure up to the desired setting. Mounting Bracket: 446-707-045 Operating Pressure Range:  PSIG  bar R210 / R220 Regulator Kits & Accessories PRIMARY – Maximum 150 10.3 Mounting Bracket Kits –  Pipe Mounting (Pair) ....................................................SA00YW57 SECONDARY – Spring Pressure Right Angle Mounting .................................................. 6-707-05   40 PSIG  Minimum  0.1        Maximum 0 .76 Service Kits – -0 PSIG ....................................................................... RKR10A*   120 PSIG  Minimum  0.1 -10 PSIG .....................................................................RKR10C*        Maximum 10 8.7 -10 PSIG (High Relieving) ..........................................RKR0C* Operating Temperature Range .......-18°C * to 65°C (0°F* to 150°F) * Parts in Kit: Diaphragms, Gasket, Bleed Orifice * Temperatures below 0°C (3°F) require moisture free air. Specifications Repeatability / Sensitivity ......................... 0.005 PSIG (0.0003 bar) Inches of Water Column = 1/8" 3 Constant Bleed Rate ...................Less than 0.08 SCFM (0.15m /hr) (Equals Bleed Rate plus other consumption) Weight ........................................................................ 1. lb (0.6 kg) 3 Total Air Consumption .....................................6 SCFH (0.1m /hr.) Materials of Construction Effect of Supply Pressure Variation of 25 PSIG (1.7 bar) on Outlet: Adjusting Stem & Capsule ......................................Stainless Steel Less than 0.005 PSIG (0.0003 bar) Body ............................................................................................Zinc Exhaust (Relief) Capacity – Control Knob .......................................................................... Plastic At 5 PSIG (0.3 bar) above 0 PSIG (1.38 bar) Setpoint 3     Standard Model ........................................... 3 SCFM (3.m /hr) Diaphragm(s) ........................................................................Buna-N 3     High-Relief Model ...................................... 11 SCFM (17m /hr) Seals ......................................................................................Buna-N Flow Capacity – Springs ......................................................................Stainless Steel At 100 PSIG (6.89 bar) Supply, 3 0 PSIG (1.38 bar) Outlet ............................. 1 SCFM (5m /hr) Valve Poppet .............................................................Stainless Steel Gauge Ports .....................................................................1/" NPTF (Can be used as additional full flow 1/" outlet ports) Pneumatic Division B7 Richland, Michigan www.wattsfluidair.com Output PSIG Catalog 0305-2 (Revised 10-07-08) Standard Regulators R119 Series 1/4, 3/8 & 1/2 Inch Ports R119 Standard Regulators Features • High Flow Performance Featuring Rugged Design for the Most IN OUT Demanding Applications • Ideal for Those Installations Calling for X80 Reverse Flow Constant Pressure with Wide Variation Option in Flow A • Diaphragm Operated Design with Balanced Poppet Design for Quick B and Accurate Regulation • Secondary Aspiration Plus Balanced .625 Dia. Poppet Provides Quick Response 15,8 Ø and Accurate Pressure Regulation C • Heavy Duty Tee Handle Adjustment E • Reverse Flow Version Available N • Panel Mount Version Available § • High Flow: 1/4" - 100 SCFM B § 3/8" - 110 SCFM D § Panel Mount 1/2" - 150 SCFM Version Port NPT BSPP R119 Regulator Dimensions Size Relieving Relieving A B C D E N Without Gauge 0-125 PSIG Reduced Pressure R119-02C, R119-03C 1/4" R119G02C R119-02C 3.00 1.38 4.60 2.74 5.98 0.96 (76) (35) (117) (705) (152) (24) 3/8" R119G03C R119-03C R119-04C 1/2" R119-04C R119G04C 3.56 1.56 5.20 3.25 6.76 1.27 With Gauge 0-125 PSIG Reduced Pressure (90) (40) (132) (83) (172) (32) 1/4" R119-02CG — inches (mm) 3/8" — R119-03CG 1/2" — R119-04CG Bold Items are Most Popular. For other models refer to ordering information below. § SCFM = Standard cubic feet per minute at 100 PSIG inlet, 75 PSIG no flow secondary setting, and 20 PSIG pressure drop. Ordering Information R 119 — 02 C /** Engineering Port Threads Port Size Reduced Options Change Designator Pressure Range — NPT 02 1/4 Inch G Gauge Will be entered at G BSPP 03 3/8 Inch A 0-25 PSIG K Non-Relieving factory. B 0-60 PSIG 04 1/2 Inch X64** Fluorocarbon O-Rings † C 0-125 PSIG and Diaphragm NOTE: Beginning on the following dates, the regulators listed will come D 0-250 PSIG X80 Reverse Flow* standard with Nylon Bottom Plugs. † 1/4" & 3/8" January 2008 X7 Brass Bottom Plug 1/2" March 2008 * Reverse flow for use downstream of control valves. ** Brass Bottom Plug Standard with BOLD ITEMS ARE MOST POPULAR. X64 Option. Pneumatic Division B26 Richland, Michigan www.wattsfluidair.com Catalog 0305- R119 Series Technical Specifications – R119 Standard Regulators Technical Information Flow Characteristics Flow Characteristics R119-02C R119-03C 100 100 6 6 1/4 Inch Ports 3/8 Inch Ports 100 PSIG (6.9 bar) 100 PSIG (6.9 bar) Primary Pressure Primary Pressure 80 5 5 75   60 50 3 3 0   5 0 1 1 B 0 0 0 0 0 0 0 60 80 100 10 0 5 50 75 100 15 150 Flow - SCFM Flow - SCFM 0 10 0 30 0 50 0 10 0 30 0 50 60 70 3 3 Flow - dm /s Flow - dm /s n n Flow Characteristics R119-04C 100 6 ! 1/2 Inch Ports WARNING 100 PSIG (6.9 bar) Primary Pressure Product rupture can cause serious injury. 5 75 Do not connect regulator to bottled gas.  Do not exceed maximum primary pressure rating. 50 3   ! CAUTION:  5 REGULATOR PRESSURE ADJUSTMENT – The working range of knob adjustment is designed to permit outlet pressures within 1 their full range. Pressure adjustment beyond this range is also possible because the knob is not a limiting device. This is a 0 0 0 5 50 75 100 15 150 175 00 common characteristic of most industrial regulators, and limiting Flow - SCFM devices may be obtained only by special design. 0 10 0 30 0 50 60 70 80 90 For best performance, regulated pressure should always be set 3 Flow - dm /s by increasing the pressure up to the desired setting. n Relieving Diaphragm, R119 Regulator Kits & Accessories Valve Assembly (1/"; 50 PSIG) ................................ RK119A50 Gauges – For Fluorocarbon Repair Kits, add X6 to Kit Number suffix. " Dial Size, 1/" Back Connection 0 to 60 PSIG (0 to 00 kPa) ..................................... K50N1060 Specifications " Dial Size, 1/" Back Connection Gauge Ports (2) .....................................................................1/ Inch 0 to 160 PSIG (0 to 1100 kPa) ................................ K50N1160 Port Threads ............................................................1/, 3/8, 1/ Inch " Dial Size, 1/" Back Connection Reduced Pressure Range ...............  to 15 PSIG (0.15 to 8.5 bar) 0 to 300 PSIG (0 to 068 kPa) ................................ K50N1300 Supply Pressure ...............................300 PSIG Maximum (0. bar) Mounting Bracket Kit –    1/", 3/8" ........................................................................... SA15Y57 Temperature Rating ...........................0°F to 15°F (.°C to 5°C) 1/" ........................................................................................ 18A57 Weight –  Panel Mount Conversion Kit –    R119-0, R119-03 ....................................... 1.8 lb. (0.8 kg) / Unit   1/", 3/8" ................................................................................. 0 6 lb. (11.79 kg) / 1-Unit Master Pack 1/" ......................................................................................... 0 R119-0 ........................................................ 3. lb. (1.5 kg) / Unit Repair Kits – 7 lb. (1.5 kg) / 8-Unit Master Pack Non-Relieving Diaphragm, Valve Assembly (1/", 3/8"; All PSIG) ................................ RK118Y Materials of Construction Relieving Diaphragm, Adjusting Screw, Springs ........................................................ Steel Valve Assembly (1/", 3/8"; All PSIG) ................................ RK119Y Body, Spring Cage ......................................................................Zinc Non-Relieving Diaphragm, Bottom Plug .............................................................................. Nylon Valve Assembly (1/"; 5, 60, 15 PSIG) ........................... RK118A Innervalve ................................................................................. Brass Non-Relieving Diaphragm, Seals ...................................................................................... Buna N Valve Assembly (1/"; 50 PSIG) ................................ RK118A50 Relieving Diaphragm, Valve Assembly (1/"; 5, 60, 15 PSIG) ........................... RK119A Pneumatic Division B7 Richland, Michigan www.wattsfluidair.com Secondary Pressure - bar Secondary Pressure - bar Secondary Pressure - PSIG Secondary Pressure - PSIG Secondary Pressure - bar Secondary Pressure - PSIG P U S H Catalog 0305- QUBE 105 Series Regulators R105 Series 1/2 & 3/4 Inch Ports R105 Regulator A Features A • Connects to Other QUBE Units Using Just Screws and O-rings (Included) B • Integral Mounting Slots Eliminate Need for Mounting Brackets • Diaphragm Operated Design with Balanced Poppet Design for Quick and Accurate Regulation F E • Panel Mountable § • High Flow: 1/" - 150 SCFM § 3/" - 150 SCFM C G D NPT BSPP R105 Regulator Dimensions Port  † † Size Relieving Relieving A* A B C D E F* F G .69 3.03 .69 3.75 1.81 1.35 .30 .55 0.81 Without Gauge 0-125 PSIG Reduced Pressure (68.3) (77.0) (68.3) (95.) (6.1) (3.1) (58.3) (6.8) (0.6) 1/" R105-04C R105G0C Inches (mm) 3/" R105-06C R105G06C * 3/8 and 1/ inch ports † 3/ inch ports With Gauge 0-125 PSIG Reduced Pressure NOTE: 1.75 Dia. (mm) hole required for panel mounting. 1/" R105-04CG — 3/" — R105-06CG Bold Items are Most Popular.  For other models refer to ordering information below. § SCFM = Standard Cubic Feet Per Minute at 100 PSIG Inlet, 75 PSIG No Flow Secondary Setting, and 0 PSIG Pressure Drop. Ordering Information   R  105  —  04  C    /** Port Size Reduced Pressure Range Options Engineering Change  Port Threads Designator  04  1/2" A 0–5 PSIG G Gauge   —  NPT Will be entered at  06  3/4" B 0–60 PSIG K Non-relieving G BSPP factory.   C  0–125 PSIG P Panel Mount Nut (Plastic) D 0–50 PSIG BOLD ITEMS ARE MOST POPULAR. Pneumatic Division A6 Richland, Michigan www.wattsfluidair.com L O C K Catalog 0305- QUBE 105 Series Technical Specifications – R105 Regulators Technical Information Flow Characteristics A R105-04C, R105-06C 100 1/2 & 3/4 Inch Ports 6 100 PSIG (6.9 bar) Primary Pressure 75 5 4 50 3 2 25 1 0 0 0 25 50 75 100 125 150 175 Rated Flow - SCFM 0 10 20 30 40 50 60 3 Flow - dm /s n ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. Specifications R105 Regulator Kits & Accessories Gauge Ports (2) .....................................................................1/ Inch Cage Kit – Cage Assembly with Knob ..................................................CKR105 Port Threads ................................................................ 1/ & 3/ Inch Control Knob ................................................................. R105-05P Supply Pressure .......................................300 PSIG Max. (0, bar) Gauges – Temperature Rating ........................0°F to 150°F (.°C to 65.5°C) " Dial Size, 1/" Back Connection Weight ............................................................ 1.6 lbs. (.7 kg) / unit 0 to 60 PSIG (0 to  bar) .......................................... K50N1060 " Dial Size, 1/" Back Connection Materials of Construction 0 to 160 PSIG (0 to 11 bar) ...................................... K50N1160 Adjusting Knob ....................................................................... Acetal " Dial Size, 1/" Back Connection Body ....................................................................................Aluminum 0 to 300 PSIG (0 to 0,7 bar) ................................... K50N1300 Bottom Plug ................................................................................Zinc Panel Mounting Bracket Kit (Bonnet Threads) ..............SAR10Y57 Cage ..........................................................Glass-Filled Acetal Plastic Face Mounting Bracket Kit (See Page A66) .................SAR105Y57 Elastomers ............................................................................ Buna N Panel Mount Nut –    Plastic ..............................................................................R10X51-P Aluminum .........................................................................R10X51-A Repair Kits – Non-Relieving Diaphragm, Valve Assembly .................... RKR105K Relieving Diaphragm, Valve Assembly ...............................RKR105 Pneumatic Division A7 Richland, Michigan www.wattsfluidair.com Secondary Pressure - bar Secondary Pressure - PSIG P U S H L Catalog 0305- QUBE 35 Series Regulators R35 Series 1/8 & 1/4 Inch Ports R35 Regulator A Features • Compact Size Allows Greater Design Flexibility • Nearly Double the Flow Capacity of Standard Miniature A Regulators; Reduces Costly Pressure Drop • Connects to Other QUBE Units Using Just Screws B and O-rings (Included) • Integral Mounting Slots Eliminate Need for Mounting Brackets F E • Piston Operated for High Flow and Low Pressure Drop • Panel Mountable § • High Flow: 1/8" - 30 SCFM C § 1/" - 0 SCFM G D NPT BSPP R35 Regulator Dimensions Port  Size A B C D E F G Relieving Relieving 1.59 1.59 .98 1.11 0.80 1.31 0.58 Without Gauge 0-125 PSIG Reduced Pressure (0.6) (0.6) (75.7) (8.) (0.3) (33.3) (1.6) 1/8" R35-01C R35G01C Inches (mm) 1/" R35-02C R35G0C NOTE: 1.5 Dia. (3mm) hole required for panel mounting. With Gauge 0-125 PSIG Reduced Pressure 1/8" R35-01CG — 1/" — R35-02CG Bold Items are Most Popular.  For other models refer to ordering information below. § SCFM = Standard Cubic Feet Per Minute at 100 PSIG Inlet, 75 PSIG No Flow Secondary Setting, and 0 PSIG Pressure Drop. Ordering Information   R  35  —  02  C    /**  Port Threads Port Size Reduced Pressure Range Options Engineering Change  Designator   —  NPT 01  1/8" A 0–5 PSIG G Gauge Will be entered at G BSPP  02  1/4" B 0–60 PSIG K Non-relieving factory.   C  0–125 PSIG P Panel Mount Nut (Plastic) T Tamperproof Adjustment BOLD ITEMS ARE MOST POPULAR. Pneumatic Division A Richland, Michigan www.wattsfluidair.com O C K Catalog 0305- QUBE 35 Series Technical Specifications – R35 Regulators Technical Information Flow Characteristics R35-01C 100 1/8 Inch Ports 6 100 PSIG (6.9 bar) Primary Pressure A 75 5 4 50 3 2 25 1 0 0 0 5 10 15 20 25 30 35 40 Rated Flow - SCFM 0 5 10 15 3 Flow - dm /s n Flow Characteristics R35-02C 100 1/4 Inch Ports 6 100 PSIG (6.9 bar) Primary Pressure 75 5 4 50 3 2 25 1 0 0 0 5 10 15 20 25 30 35 40 45 Rated Flow - SCFM 0 5 10 15 20 3 Flow - dm /s n ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. R35 Regulator Kits & Accessories Specifications Gauge Ports (2) .....................................................................1/8 Inch Cage Kits – A Range............................................................................. CKR35A Port Threads ................................................................ 1/8 & 1/ Inch B & C Range....................................................................CKR35BC Supply Pressure .......................................300 PSIG Max. (0, bar) Control Knob ................................................................... R35-055P Temperature Rating ...........................0°F to 15°F (.°C to 5°C) Gauges – Weight ............................................................0.8 lbs. (.37 kg) / Unit 1-1/" Dial Size, 1/8" Back Connection 19.8 lbs. (8.98 kg) / -Unit Master Pack 0 to 60 PSIG (0 to  bar) .......................................... K515N18060 1-1/" Dial Size, 1/8" Back Connection Materials of Construction 0 to 160 PSIG (0 to 11 bar) ...................................... K515N18160 Adjusting Knob ....................................................................... Acetal Panel Mounting Bracket Kit (Bonnet Threads) .............. SA161X57 Body .............................................................................................Zinc Face Mounting Bracket Kit (See Page A66)  ..................SAR35Y57 Bottom Plug ....................................................... Glass-Filled Acetal Panel Mount Nut –  Cage .........................................................................................Plastic   Plastic ..............................................................................R05X51-P Elastomers ............................................................................ Buna N Aluminum .........................................................................R05X51-A Repair Kits – Non-Relieving Piston, Valve Assembly .............................. RKR30K Relieving Piston, Valve Assembly .........................................RKR30 Pneumatic Division A3 Richland, Michigan www.wattsfluidair.com Secondary Pressure - bar Secondary Pressure - bar Secondary Pressure - PSIG Secondary Pressure - PSIG Catalog 0305-2 Precision Regulators R230 Series 1/4 & 3/8 Inch Ports R230 High Flow Precision Regulator Features • Adjusting Knob. • Diaphragm Design for Good Repeatability, Response and Sensitivity • Balanced Poppet B • Two Full Flow Gauge Ports Mounting Holes • Precise Regulation. Will Sense a Decrease in Downstream Pressure as Small as 1/4" of B D Water Column (0.010 PSIG) • High Fow Capacity. Flows of 1/4" NPT E Gauge Ports 80 SCFM Attainable with Minimal Drop (2) C • Stable Output. Dampening Action of Aspiration Tube makes Regulator Insensitive to Changes in Flow • On-line Maintenance. Can be Serviced Without Removal of Air Line A R230 Regulator Dimensions The R230 is designed for applications Applications A B C D E that require high flow capacity and 3.00 0.38 3.40 6.06 2.25 The R230 regulators are an ideal accurate process control. A poppet (76) (10) (86) (154) (57) choice for any application that calls valve which is balanced by utilizing a inches for accurately maintained output (mm) rolling diaphragm, insures a constant pressure under high flow conditions. output pressure even during wide This includes, but is not limited to supply pressure variations. Stability of such applications as: regulated pressure is maintained under Test Equipment varying flow conditions through the use of an aspirator tube which adjusts the • Gas Mixing air supply in accordance with the flow • Valve Operators velocity. • Positioning Cylinders • Laboratory Equipment • Web Tensioning • Clutch & Brake Controls • Roll Loading • Test Panels • Actuators Ordering Information Reduced Pressure Range (PSIG) Relieving Port Size 0 to 2 0 to 30 0 to 60 0 to 150 1/4" R230-02E R230-02B R230-02C R230-02D In / Out Ports 3/8" N/A R230-03B R230-03C R230-03D Pneumatic Division B48 Richland, Michigan www.wattsfluidair.com Catalog 0305- R30 Series Technical Specifications – R230 High Flow Precision Regulators Technical Information .33 .7 Dia. Thru Dia. Thru 100 PSI Supply (8.7) (6.9) 80 (552) () Places (3) Places 1.00 75 (517) R (5) 2 to 150 PSIG (15 to 1000 kPa) 3/8 NPT  70 (483) 65 (448) 55˚ .5 3.00 60 (414) (57) (76) 55˚ 55 (379) 50 (345) 45 (310) .75 .50 1 to 60 PSIG (7 to 400 kPa) 1/4 NPT  .67 D.B.C. 40 (276) (19) (13) (76) 1.13 1.38 B 35 (241) (9 ) (35) 30 (207) 0 to 30 PSIG (0 to 200 kPa) 1/4 NPT  Mounting Bracket: 446-707-025 25 (172) 20 (134) 15 (103) 0 to 15 PSIG (0 to 15 kPa) 1/4 NPT  10 (69) 5 (34) 0 to 2 PSIG (0 to 15kPa) 1/4 NPT  0 (0) 5 15 25 35 45 55 65 75 ! WARNING (8.5) (25.5) (42.5) (59.4) (76) (93.5) (110.5) (127.5) 10 20 30 40 50 60 70 80 (17) (34) (51) (68) (85) (102) (119) (136) Product rupture can cause serious injury. Do not connect regulator to bottled gas. Flow Do not exceed maximum primary pressure rating. 3 SCFM (m /hr)   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range of knob adjustment is designed to permit outlet pressures within their full range. Pressure adjustment beyond this range is also possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. Operating Pressure Range –  PSIG  bar  R230 Regulator Kits & Accessories   PRIMARY –  Maximum 50 17 Mounting Bracket Kit  .................................................... 6-707-05 Port Threads .................................................................................1/" Service Kits – Relieving Exhaust (Relief) Capacity ..................................................0 SCFM 0 to  PSIG ..................................................................... RKR30E* (Downstream pressure 5 PSI above set pressure) 0 to 30 PSIG ................................................................... RKR30B* 0 to 60 PSIG ...................................................................RKR30C* Repeatability / Sensitivity ................... ±0.010 PSIG (±0.00068 bar) 0 to 150 PSIG .................................................................RKR30D* Inches of Water Column = 1/" * Parts in Kit: Diaphragm, Poppet, O-ring Response ...............................................................................50 ms 3 The valve will open to full flow and fill a volume of 150 cm Specifications Weight .................................................................1 lb. 10 oz. (0.7 kg) Constant Bleed Rate ............................................ 1.0 to 1.5 SCFH (Depending upon output pressure) Materials of Construction Gauge Ports ................................................................ Two Ports 1/" Adjusting Stem & Spring ......................................................... Steel (Can be used as additional Full Flow 1/ Inch Outlet Ports) Biased Spring ............................................................Stainless Steel Effect of Supply Pressure Variation – Body, Bonnet .................................................................... Aluminum Less than 0.1 PSIG for 100 PSIG (6.89 bar) change Control Knob ..........................................................................Plastic Exhaust (Relief) Capacity –  SCFM with downstream pressure 5 PSIG above set pressure. ... Diaphragm .......................... Buna-N Elastomer and Polyester Fabric Exhaust commences at 0.01 PSIG above set pressure. Seals ..................................................................................... Buna-N Flow Capacity – Valve Poppet ........................................................................... Brass At 100 PSIG (6.89 bar) Supply,  Valve Poppet Seat ................................................................ Buna-N 80 PSIG (5.5 bar) Outlet ...............................80 SCFM (37.8 dm /s) Operating Temperature Range ................................... -0°C to 71°C (-0°F to 160°F) Pneumatic Division B9 Richland, Michigan www.wattsfluidair.com Output  PSIG (kPa) Catalog 0305- R10 / R11 Series Technical Specifications – R10 / R11 General Purpose Regulators Technical Information Flow Characteristics Flow Characteristics R10-04C R10-02C / R10-03C 100 100 1/2 Inch Ports 1/4 & 3/8 Inch Ports 6 100 PSIG (6.9 bar) Primary Pressure 6 100 PSIG (6.9 bar) Primary Pressure 75 5 75 5   50 50 3 3 B   5 5 1 1 0 0 0 0 0 10 0 30 0 50 60 70 80 90 0 0 0 60 80 100 10 Rated Flow - SCFM Rated Flow - SCFM 0 10 0 30 0 0 10 0 30 0 50 3 Flow - dm /s 3 n Flow - dm /s n ! WARNING   ! CAUTION: REGULATOR PRESSURE ADJUSTMENT – The working range Product rupture can cause serious injury. of knob adjustment is designed to permit outlet pressures within Do not connect regulator to bottled gas. their full range. Pressure adjustment beyond this range is also Do not exceed maximum primary pressure rating. possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. R10 / R11 Regulator Kits & Accessories Specifications Control Knob (R10) .............................................................. R10Y5 Gauge Ports (2) .....................................................................1/ Inch Tee Handle (R11) ................................................................ SA16Y53 Port Threads ............................................................1/, 3/8, 1/ Inch Gauges – Supply Pressure ...............................300 PSIG Maximum (0. bar) " Dial Size, 1/" Back Connection Temperature Rating ...........................0°F to 15°F (.°C to 5°C) 0 to 60 PSIG (0 to 00 kPa) ..................................... K50N1060 Weight ............................................................. 1.3 lb. (0.59 kg) / Unit " Dial Size, 1/" Back Connection 3 lb. (1.51 kg) / -Unit Master Pack 0 to 160 PSIG (0 to 1100 kPa) ................................. K50N1160 Materials of Construction " Dial Size, 1/" Back Connection 0 to 300 PSIG (0 to 068 kPa) ................................. K50N1300 Adjusting Knob –    R10 ....................................................................................... Acetal Mounting Bracket Kit ......................................................SAR10Y57 R11 (Tee Handle) ................................................................... Steel Panel Mount Nut –  Body .............................................................................................Zinc   Plastic ..............................................................................R10X51-P Aluminum .........................................................................R10X51-A Bottom Plug .............................................................................. Nylon Optional .................................................................................. Brass Repair Kits – Non-Relieving .................................................................. RKR10KY Elastomers ............................................................................ Buna N Non-Relieving (Viton) ................................................RKR10KYX6 Spring Case – Relieving ............................................................................ RKR10Y R10 ....................................................................................... Acetal Relieving (Viton) .......................................................... RKR10YX6 R11 ...........................................................................................Zinc Cage Kit –     R10 ................................................................................... CKR10Y R11 ................................................................................... CKR11Y Pneumatic Division B5 Richland, Michigan www.wattsfluidair.com Secondary Pressure - bar Secondary Pressure - PSIG Secondary Pressure - bar Secondary Pressure - PSIG