VMIC VMICPCI-7753-05901

VMICPCI-7753 ® ® ® ® Intel Celeron /Pentium III CompactPCI System Controller ® ® • Single slot system controller, Celeron and Pentium III socket 370 processor-based single board computer (SBC)  Up to 192 Mbyte IDE CompactFlash (optional)  Four programmable 16-bit timers  32 Kbyte of nonvolatile SRAM  Software-selectable watchdog timer with reset  Remote boot support over Ethernet  PMC expansion site ®  CompactPCI 2.0 revision 3.0-compliant system slot controller ® using Intel 21154 PCI-to-PCI bridge (64-bit/33 MHz)  Supports Celeron and Pentium III processors up to 866 MHz  Up to 512 Mbyte PC-133 SDRAM using one 144-pin SODIMM module  Integrated 2D/3D graphics (built-in VGA maximum resolution (8 bpp at 1,600 x 1,200, 16 bpp at 1,600 x 900, and 24 bpp at 1,280 x 1,024) processor also provides 128 Kbyte of advanced transfer cache (on-die,  Onboard Fast Ethernet controller supporting 10BaseT and 100BaseTX interfaces full speed level 2 cache) using dual independent bus architecture for  Onboard Ultra DMA/100 IDE hard drive and floppy drive high bandwidth and performance. This L2 cache operates at the same controllers with CompactPCI rear I/O clock frequency as the processor, thus improving performance. The  Enhanced parallel port with ECP/EPP modes supported, Pentium III offers 256 Kbyte of level 2 cache. available at front panel or through the CompactPCI backplane connectors (front panel access requires connector adapter to DRAM Memory: The VMICPCI-7753 accepts one 144-pin PC-133 interface to the micro-D-style connector) SODIMM SDRAM module for a maximum memory capacity of  Two high performance 16550-compatible serial ports. One 512 Mbyte. The onboard DRAM is dual ported to the CompactPCI bus. RJ11 connector available at the front panel, and both serial ports available through CompactPCI backplane connectors. Flash Memory: The VMICPCI-7753 provides up to 192 Mbyte of  Two USB ports (one front panel USB port, one USB port CompactFlash memory accessible through the secondary IDE port. The available via rear I/O)  PS/2-style keyboard and mouse port on front panel VMICPCI-7753 BIOS includes an option that allows the board to boot  Real time clock and miniature speaker included from the flash memory.  Passive heat sink The onboard flash emulates a hard disk drive. Accesses to flash are ® ®  Operating system support for Windows NT , Windows 2000, ® ® ® ® identical to file operations for a hard disk drive. Because of the hard VxWorks , Solaris™, Linux , LynxOS and QNX disk emulation feature, no OS-specific software drivers are required for Functional Characteristics flash memory operation. Microprocessor: The VMICPCI-7753 brings Intel socket 370 Celeron BIOS: System BIOS, video BIOS, and LAN Boot BIOS are provided in and Pentium III to CompactPCI bus, offering processor speeds of reprogrammable flash memory. BIOS loader software can be provided. 566 MHz to 866 MHz. The motherboard supports the flex feature, which Super VGA Controller: High-resolution graphics and multimedia- allows either processor to be supported. Both processors have 32-bit quality video are supported on the VMICPCI-7753 by an internal 815E addressing and a 64-bit data bus. Their superscalar architecture allows AGP graphics controller. The controller uses 4 Mbyte synchronous three instructions to be executed per clock cycle. A dynamic branch DRAM display cache with a high-bandwidth 64-bit data interface and prediction unit, separate instruction and data caches, and MMX™ supports screen resolutions up to 1,600 x 1,200 x 64 K colors. technology also increase the processor’s performance. The Celeron GE Fanuc Automation, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 1 VMICPCI-7753  Detailed boot configuration screens Ordering Options  Comprehensive diagnostic March 6, 2002 800-657753-000 F A B C D E F  Optional disabling of local boots VMICPCI-7753 – 0  Dual-boot option lets users select network or local booting A = Processor 0 = Reserved 1 = 566 MHz Celeron SBC 16-bit Timers: The VMICPCI-7753 provides the user with four 16-bit 2 = 733 MHz Celeron SBC timers (in addition to system timers). These timers are mapped in I/O 3 = 733 MHz Pentium III SBC 4 = 866 MHz Pentium III SBC space, are completely software programmable, and can generate PCI B = SDRAM 0 = Reserved interrupts. 1 = Reserved 2 = 32 Mbyte Watchdog Timer: The VMICPCI-7753 provides a software- 3 = 64 Mbyte programmable watchdog timer. The watchdog timer is enabled under 4 = 128 Mbyte 5 = 256 Mbyte software control. Once the watchdog timer is enabled, onboard 6 = 512 Mbyte C = CompactFlash software must access the timer within the specified timer period, or the 0 = None output of the timer will reset the unit. 1 = 8 Mbyte 2 = Reserved 3 = 32 Mbyte Nonvolatile SRAM: The VMICPCI-7753 provides 32 Kbyte of 4 = Reserved nonvolatile SRAM. The contents of the SRAM are preserved when +5 V 5 = 64 Mbyte 6 = Reserved power is interrupted or removed from the unit. 7 = Reserved 8 = 128 Mbyte Serial Ports: Two 16550-compatible serial ports are featured on the 9 = Reserved G = 192 Mbyte VMICPCI-7753. Each serial channel has an independent 16-byte FIFO to D = Solder Side Cover support baud rates up to 115 Kbaud. 0 = No Cover 1 = Cover Installed USB Port: The VMICPCI-7753 provides two Universal Serial Bus (USB) E = Custom Option 0 = Reserved ports. One is available on the front panel. The second is accessed via 1 = Standard F = 0 (Reserved for future use.) the backplane. CompactPCI Rear Transition Utility Board VMIACC-0576 Keyboard and Mouse Ports: The VMICPCI-7753 supports a combined The VMIACC-0576 mounts in the rear transition area of the backplane and provides PS/2 keyboard and mouse connector for peripherals. A Y-adapter cable access to the serial, USB, enhanced IDE, floppy disk, and PMC I/O connectors by way of the J3 and J5 connectors. The VMIACC-0576 is sold separately. is supplied with the unit. For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444  FAX (256) 882-0859 Reset Switch and Annunciators: A small push-button switch on the Email: info.embeddedsystems@gefanuc.com front panel will reset the VMICPCI-7753 and also generate a reset to the Web Address: www.gefanuc.com/embedded Copyright © 2004 by VMIC CompactPCI bus. Six LEDs are visible on the front panel: power, board Specifications subject to change without notice. status, IDE activity, LAN activity, LAN mode (10 or 100 Mbit mode), and Ethernet Controller: The VMICPCI-7753 supports Ethernet LANs with temperature status. A small speaker is also included on the the 82559ER PCI Ethernet controller. 10BaseT and 100BaseTX options VMICPCI-7753 to provide PC/AT sound output. are supported via an RJ45 connector. PMC Expansion Site: The VMICPCI-7753 supports IEEE P1386 Remote Ethernet Booting: The VMICPCI-7753 utilizes Lanworks common mezzanine card specification with a 5 V PCI mezzanine card Technologies, Inc.’s BootWare BIOS. BootWare provides the ability to (PMC) expansion site. PMC I/O is routed to the CompactPCI backplane remotely boot the VMICPCI-7753, and provides the following features: connectors.  NetWare (802.2, 802.3, or Eth II), TCP/IP (DHCP or BootP), and PXE boot support  Unparalleled boot sector virus protection GE Fanuc Automation, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 2 VMICPCI-7753  Provides arbitration support for seven CompactPCI bus devices; a The following is a partial list of commercially available PMC modules: programmable two-level arbiter  Fibre Channel  Provides enhanced address decoding: – A 32-bit I/O address range  Analog and digital I/O – A 32-bit memory-mapped I/O address range  High speed serial and parallel I/O – A 64-bit prefetchable memory address range  Networking adapters: FDDI, ATM, Ethernet, Fast Ethernet – ISA-aware mode for legacy support in the first 64 Kbyte  PMC-to-PC Card adapter of I/O address range – VGA addressing and VGA palette snooping support for VGAs  MIL-STD-1553 bus interface located on CompactPCI bus  SRAM – Supports PCI transaction forwarding for the following commands:  Flash - All I/O and memory commands - Type 1 to type 1 configuration commands  Solid-state disk - Type 1 to type 0 configuration commands (downstream only)  Data acquisition cards - All type 1 to special cycle configuration commands  SCSI-2 adapter  Includes downstream lock support  Parallel links  Supports either 5 or 3.3 V signaling environments  Octal DSP  Quad SIO  GPIB Operating System and Software Support  FAX/modem GE Fanuc Embedded Systems has a wide range of software products  PMC-to-PMC expanders designed to run on Intel processor-based SBCs, such as the  T1/E1 and serial communications interfaces VMICPCI-7753. These products are aimed at developers who are incorporating GE Fanuc SBCs, I/O boards, and workstations into CompactPCI bus Bridge: The VMICPCI-7753 is fully compliant with systems. Windows NT, VxWorks, Windows 2000, QNX, Linux, LynxOS CompactPCI Rev. 2.1, PCI 2.1, and PCI-to PCI Bridge Architecture and Solaris are the operating systems supported. Rev. 1.1. This system slot board provides the following features for adapters loaded in the CompactPCI subsystem. Windows NT OS Support — VMISFT-9421 Generic Device Driver: The VMISFT-9421 is very useful in those cases where the driver  64-bit/33 MHz CompactPCI interface for peripheral devices is not available.  Implements delayed transactions for all PCI configuration, I/O, and memory read commands — up to three transactions simultaneously The generic hardware driver is a set of functions and utilities that in each direction makes it possible to easily develop, debug, and run standard  Allows 152 bytes of buffering (data and address) for upstream Windows NT applications that access any PC Card (PCMCIA), PMC, and posted memory write commands and 88 bytes of buffering for CompactPCI devices. downstream posted memory write commands — up to nine upstream and five downstream posted write transactions ® Visual Basic , C/C++, and any other language that can call functions in simultaneously a dynamic link library or connect to a DDE server are supported.  Allows 152 bytes of read data buffering upstream and 152 bytes of read data buffering downstream VxWorks OS Support — VMISFT-7418 Board Support Package:  Provides concurrent primary and CompactPCI bus operation to The VMISFT-7418, VxWorks board support package (BSP), is a Wind isolate traffic River Systems, Inc. certified BSP for GE Fanuc’s series of CompactPCI  Provides seven CompactPCI clock outputs: Pentium processor-based computers that is required to run the VxWorks – Low skew, permitting direct drive of option slots OS. Complete source code is provided, thus giving the user the utmost – Individual clock disables, capable of automatic configuration flexibility in system reconfiguration. Along with the Wind River during reset Systems, Inc.-supplied software, a VxWorks OS kernel can be built and GE Fanuc Automation, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 3 VMICPCI-7753 rebuilt for specific applications. For example, the user can easily Power Requirements: reconfigure standard output to be via serial port or SVGA. +5 VDC (±5 percent), 4 A (typical), 5.5 A maximum +3.3 VDC, 2.4 A (typical), 4.7 A maximum VMISFT-7418 is linked by the user with VxWorks OS, thus allowing +12 VDC (±5 percent), 100 mA (typical), 200 mA maximum software applications created with Wind River Systems, Inc.’s -12 VDC (±5 percent), 50 mA (typical), 100 mA maximum development system to load and run on the particular GE Fanuc SBC hardware being used. Serial ports, parallel ports, keyboard, text mode Note: The currents at +12 and -12 VDC are specified with the serial video, and Ethernet are all supported, as well as floppy and IDE hard connectors open. disk drives that can be connected to the computer boards. The BSP also Temperature: provides Flash boot, NVRAM, and timer support. Operating: 0 to +55 °C VMISFT-7418 allows VxWorks applications to have access to the (Air flow requirement as measured at output side of heatsink is to be CompactPCI bus including memory, I/O, and configuration cycles. The greater than 350 LFM) BSP provides interprocessor communications capability via shared Storage: -25 to +80 °C memory. The interprocessor communications provides system slot SBC Relative Humidity: 10% to 90%, noncondensing to peripheral-slot communications via the CompactPCI bus. PMC Expansion Site Connector: QNX, Solaris, Linux and LynxOS: QNX, Solaris, Linux, and LynxOS 5 V signaling, types 1 and 2 are supported by VMICPCI-7xxx without the need for additional 32-bit PCI bus, 33 MHz maximum software drivers. The timers and battery-backed RAM may be accessed MTBF: 162,081 hours (Bellcore) directly by application code. Solder Side Cover: The VMICPCI-7753 is optionally available with an antistatic, nonconductive solder side cover. This will prevent accidental Trademarks contact of conductive components between neighboring boards. MMX is a trademark and Celeron, Intel, and Pentium are registered trademarks of Intel Corporation. CompactPCI is a registered trademark of PCI Industrial Computer Manufacturers’ Group. Visual Basic, Physical/Environmental Specifications Windows, and Windows NT are registered trademarks of Microsoft Dimensions: 6U single slot Eurocard form factor Corporation. Other registered trademarks are the property of their Height 9.2 in. (233.4 mm) respective owners. Depth 6.3 in. (160 mm) Thickness 0.8 in. (20.3 mm) GE Fanuc Automation, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 4 VMICPCI-7753 Pentium III Celeron Processor with Processor with or 256 Kbyte ATC L2 Cache 128 Kbyte L2 Cache Host Bus 4 Mbyte Display Cache 815E Graphics and Memory PC-133 AGP or Video Controller Hub (GMCH) Memory Bus PC-100 SVGA Intel 82815 SDRAM SODIMM Parallel Port BIOS Advanced Hub Firmware Architecture (AHA) Hub Bus Front Panel Intel 82802AB USB Port CompactPCI COM Port 1 CompactPCI I/O Controller USB CompactPCI Hub COM Port 2 SUPER- CompactPCI (ICH2) I/O LPC/FWH IDE CompactPCI Ultra DMA Bus Intel 82801BA Floppy Drive National PC87366 PMC Expansion 5 V, 3.3 V PS/2 Keyboard PCI Bus (32-bit) and Mouse PCI Embedded Ethernet Interface PCI Bridge Controller FPGA Intel 21154 Intel 82559ER Timers LAN 32 Kbyte CompactPCI Bus (64-bit) 10BaseT NVRAM 100BaseTX Figure 1. VMICPCI-7753 Block Diagram GE Fanuc Embedded Systems Information Centers Additional Resources USA and the Americas: Europe, Middle East and Africa: For more information, please visit the Huntsville, AL 1 800 322-3616 Edinburgh, UK 44 (131) 561-3520 GE Fanuc Embedded Systems web site at: 1 (256) 880-0444 Paris, France 33 (1) 4324 6007 www.gefanuc.com/embedded Ventura, CA 1 (805) 650-2111 Greenville, SC 1 (864) 627-8800