VMICPCI-7699 Single-Slot Pentium II/III Embedded Module Peripheral-Slot CompactPCI Single-Board Computer with High-Availability Hot Swap and Dual PMC • Single-slot Pentium® II/III processor-based embedded module single-board computer (SBC) • Special features for embedded applications — Up to 96 Mbyte IDE CompactFlash (optional) — Three programmable 16-bit timers — 32 Kbyte of nonvolatile SRAM — Remote Ethernet booting — Software-selectable watchdog timer with reset — Dual PMC expansion sites — Peripheral-slot SBC (embedded PCI bridge allows on-board Pentium II/III processor to operate independent of the CompactPCI® (CPCI) bus) — Compliant with CPCI 2.0 revision 2.1 — Compliant with PICMG 2.1 Rev. 1.0 for high-availability hot swap — Support for geographical addressing 2 — Supports system management bus (I C) • Standard features include — Pentium II/III processor with speeds up to 500 MHz — Up to 256 Mbyte SDRAM using two 144-pin SODIMM modules — 64-bit AGP SVGA controller with 2 Mbyte SGRAM — On-board Fast Ethernet controller supporting 10BaseT and 100BaseTX interfaces — On-board Ultra-DMA-33 hard drive and floppy drive controllers with CPCI J3 I/O — Two high-performance 16550-compatible serial ports — One USB port — PS/2-style keyboard and mouse port on front panel Ordering Options — Real-time clock and miniature speaker included January 12, 2001 800-657699-000 F ABC – D E F — Passive heat sink • Operating system support VMICPCI-7699 – – — Windows NT®/Windows® 2000 A = Processor — VxWorks 0 = Not Used — QNX 1 = Reserved — Solaris 2 = Reserved — Linux 3 = Reserved — LynxOS 4 = 333 MHz Pentium II Processor 5 = Reserved APPLICATIONS 6 = 500 MHz Pentium III Processor B = SDRAM Memory • Telecommunications 0 = Reserved • Simulation 1 = Reserved • Instrumentation 2 = Reserved • Industrial control 3 = 32 Mbyte • Process control and monitoring 4 = 64 Mbyte • Factory automation 5 = 128 Mbyte • Intelligent networked PLC controllers 6 = 256 Mbyte 7 = Reserved • Automated test C = CompactFlash Drive • Data acquisition 0 = None 1 = 8 Mbyte MICROPROCESSOR — The VMICPCI-7699 brings 2 = Reserved Intel® Pentium II/III processor with MMX™ to CPCI bus, 3 = Reserved 4 = 64 Mbyte offering processor speeds up to 500 MHz. The Pentium II/III 5 = 96 Mbyte processor has 32-bit addressing and a 64-bit data bus. Its 6 = 128 Mbyte superscalar architecture allows three instructions to be 7 = 160 Mbyte 8 = 192 Mbyte executed per clock cycle. A dynamic branch prediction unit, CPCI Rear Transition Utility Board separate instruction and data caches, and MMX technology also increase the Pentium II/III processor’s performance. The VMIACC-0577 Pentium II/III processor also provides internal L2 cache using The VMIACC-0577 mounts in the rear transition area of the backplane and provides access to the serial, USB, enhanced IDE, floppy disk, and PMC I/O connectors by way of the J3 dual independent bus architecture for high bandwidth and and J5 connectors. The VMIACC-0577 is sold separately. performance. Video Connector Adapter Kit HIGH-AVAILABILITY HOT SWAP — The A connector adapter, part number 360-000168-004, is available to adapt the product’s VMICPCI-7699 complies with PICMG 2.1 rev. 1.0 standard front panel, 9-pin video port micro-D connector to a standard-D 15-pin connector. This adapter is sold separately. for CPCI hot swap. The VMICPCI-7699 complies with the For Ordering Information, Call: high-availability provisions of this standard. This means that, 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 in addition to being able to remove and replace the board with E-mail: info@vmic.com Web Address: www.vmic.com the system operating, processing can automatically be Copyright © May 1998 by VMIC switched to a second backup board already installed in the Ω Specifications subject to change without notice. system in the event of failure in the primary processor. 1 SUPER VGA CONTROLLER — High-resolution DRAM MEMORY — The VMICPCI-7699 accepts graphics and multimedia-quality video are supported on the 144-pin SODIMM SDRAM modules for a maximum VMICPCI-7699 by an Intel 69000 AGP graphics controller. memory capacity of 256 Mbyte. The on-board DRAM is dual The controller contains on-chip 2 Mbyte synchronous ported to the CPCI bus. BIOS — System BIOS, video BIOS, and LAN Boot 1. The VMICPCI-7699 requires an adapter cable (available BIOS are provided in reprogrammable flash memory. BIOS separately) to adapt the board’s micro-DB9 connector to loader software is also provided. the standard VGA high-density DB15 connector. VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308 1 VMICPCI-7699 DRAM with a high-bandwidth 64-bit data interface and board status, IDE activity, LAN activity, LAN Mode supports screen resolutions up to 1,600 x 1,200 x 256 colors. (10 or 100 MHz mode), and hot-swap status. A small speaker is also included on the VMICPCI-7699 to provide PC/AT Ethernet CONTROLLER — The VMICPCI-7699 sound output. supports Ethernet LANs with the Intel 82559 PCI Ethernet controller. 10BaseT and 100BaseTX options are supported PMC EXPANSION SITES — The VMICPCI-7699 via an RJ45 connector. supports the IEEE P1386 common mezzanine card specification with two 5 V PCI mezzanine card expansion REMOTE Ethernet BOOTING — The sites. PMC I/O is routed to the CPCI backplane connectors. VMICPCI-7699 utilizes Lanworks Technologies, Inc.’s BootWare®. BootWare provides the ability to remotely boot The following is a partial list of commercially available the VMICPCI-7699 using NetWare, TCP/IP, or RPL network PMC modules: protocols. • Fibre Channel BootWare Features: • Analog and digital I/O • NetWare, TCP/IP, RPL network protocol support • High-speed serial and parallel I/O • Unparalleled boot sector virus protection • Networking adapters: FDDI, ATM, Ethernet, Fast Ethernet • Detailed boot configuration screens • PMC-to-PC Card adapter • Comprehensive diagnostics • MIL-STD-1553 bus interface • Optional disabling of local boots • SRAM • Dual-boot option lets users select network or local booting • Flash • Solid-state disk SERIAL PORTS — Two 16550-compatible serial ports • Data acquisition cards are featured on the VMICPCI-7699. Each serial channel has • SCSI-2 adapter an independent 16-byte FIFO to support baud rates up to • Parallel links 115 kHz. • Octal DSP USB PORT — The VMICPCI-7699 provides one • Quad SIO Universal Serial Bus (USB) port. The port is available at the • GPIB CPCI backplane connector. • FAX/modem KEYBOARD AND MOUSE PORTS — The • Second Ethernet VMICPCI-7699 supports a combined PS/2 keyboard and • PMC-to-PMC expanders mouse connector for peripherals. A Y-adapter cable is supplied with the unit. Contact VMIC for more information concerning third-party PMC modules and compatibility. FLASH MEMORY —The VMICPCI-7699 provides up to 96 Mbyte of CompactFlash memory accessible through the CPCI bus BRIDGE — The VMICPCI-7699 secondary IDE port. The VMICPCI-7699 BIOS includes an incorporates a PCI peripheral device that performs PCI option to allow the board to boot from the flash memory. bridging functions for embedded and intelligent I/O applications. The PCI device acts as a gateway to an The on-board flash emulates a hard disk drive. Accesses intelligent subsystem. It allows the local VMICPCI-7699 to flash are identical to file operations for a hard disk drive. Pentium II processor to configure and control the on-board Because of the hard disk emulation feature, no OS-specific local subsystem independent from the CPCI bus host software drivers are required for flash memory operation. processor. The VMICPCI-7699 local PCI subsystem is 16-bit TIMERS — The VMICPCI-7699 provides the presented to the CPCI bus host as a single CPCI device. user with three 16-bit timers which are 82C54 compatible. The VMICPCI-7699 PCI bridge device provides the These timers are mapped in I/O space, and are completely following features: software programmable. WATCHDOG TIMER — The VMICPCI-7699 provides PCI Interface a software-programmable watchdog timer. The watchdog • Fully compliant with the PCI Local Bus Specification, timer is enabled under software control. Once the watchdog Revision 2.1 timer is enabled, on-board software must access the timer • 3.3 V operation with 5.0 V tolerant I/O within the specified timer period, or the output of the • Concurrent local (secondary) and CPCI (primary) bus watchdog timer will reset the unit. operation NONVOLATILE SRAM — The VMICPCI-7699 • Supports full hot swap and high-availability hot swap per provides 32 Kbyte of nonvolatile SRAM. The contents of the PICMG 2.1 Rev. 1.0 SRAM are preserved when +5 V power is interrupted or removed from the unit. Buffer Architecture RESET SWITCH AND ANNUNCIATORS — A • Queuing of multiple transactions in either direction small push-button switch on the front panel will reset the • 256 byte of posted write (data and address) buffering in VMICPCI-7699. Only the on-board VMICPCI-7699 logic each direction will be reset. There will be no reset generated on the CPCI • 256 byte of read data buffering in each direction bus. Six LEDs are visible on the front panel: +5 V power, • Four delayed transaction entries in each direction 2 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 VMICPCI-7699 Configuration Registers and CSRs be connected to the computer boards. The BSP also provides Flash boot, NVRAM, and timer support. • Two sets of standard PCI configuration registers corresponding to the local and CPCI interfaces. Each set is VMISFT-7418 allows VxWorks applications to have accessible from either the local or CPCI interface. access to the CPCI bus including memory, I/O, and configuration cycles. The BSP provides interprocessor • Four 32-bit base address configuration registers mapping communications capability. The interprocessor the control and status registers (CSRs) communications provides system-slot SBC to peripheral-slot Transaction Forwarding communications via the CPCI bus. • Four primary interface base address configuration registers QNX, LynxOS, and Solaris for downstream forwarding with size and prefetchability QNX, LynxOS, and Solaris are supported by programmable for all four address ranges VMICPCI-769x without the need for additional software • Direct offset address translation for downstream memory drivers. The timers and battery-backed RAM may be and I/O transactions accessed directly by application code. • Three secondary interface address configuration registers SPECIFICATIONS specifying local address ranges for upstream forwarding with size and prefetchability programmable for all three 6U Eurocard format, one slot address ranges Height 9.2 in. (233.4 mm) • Inverse decoding above 4 Gbyte address boundary for Depth 6.3 in. (160 mm) upstream DACs • Ability to generate type 0 and type 1 configuration Thickness 0.8 in. (20.3 mm) commands on the primary or secondary interface via Power Requirements: configuration or I/O CSR accesses +5 VDC (±5 percent), 1.3 (typical), 2.4 A maximum OPERATING SYSTEM AND SOFTWARE +3.3 VDC (±5 percent), 2.2 (typical), 2.5 A maximum SUPPORT — VMIC has a wide range of software products +12 VDC (±5 percent), 105 mA (typical), 200 mA designed to run on Intel processor-based SBCs, such as the maximum VMICPCI-7699. These products are aimed at developers who are incorporating VMIC SBCs, I/O boards, and workstations -12 VDC (±5 percent), 50 mA (typical), 75 mA into systems. Windows NT/Windows 2000 and VxWorks are maximum the most common operating systems supported. Note: The currents at +12 and -12 VDC are specified Windows NT/Windows 2000 with the serial connectors open. The VMISFT-9421, generic hardware driver for Operating Temperature: 0 to 55 ˚C (Forced air Windows NT/Windows 2000, is not required to run cooling required, 250 LFM minimum) Windows NT/Windows 2000 on the VMICPCI-7699, but is Relative Humidity: 10 to 90 percent, very useful in those cases where the driver for peripheral noncondensing devices is not available. PMC Expansion Site Connectors: The generic hardware driver is a set of functions and utilities that makes it possible to easily develop, debug, and 5 V signaling, types 1 and 2 run standard Windows NT/Windows 2000 applications that 32-bit PCI bus, 33 MHz maximum access any PC Card (PCMCIA), PMC, and CPCI devices. Visual Basic®, C/C++, IOWorks® Soft Logic Link™ COMPATIBLE PRODUCTS and any other language that can call functions in a dynamic PMC Expansion Sites: VMIC supports the PMC link library or connect to a DDE server are supported. expansion sites with its VMIPMC-5579 Reflective VxWorks Memory interfaces. Reflective Memory is VMIC’s family of networking products that provides high-speed The VMISFT-7418, VxWorks board support package network communication using memory. Data written (BSP), is a Wind River Systems, Inc. certified BSP for into local memory is also written into the memories of all VMIC’s series of CPCI Pentium processor-based computers other nodes on the network. This error-free transmission that is required to run the VxWorks OS. With the SBC, requires no overhead from the host processor. VxWorks, the BSP, and other CPCI equipment from VMIC, implementations can be created for a wide variety of TRADEMARKS applications, including real-time factory automation, Soft Logic Link is a trademark and IOWorks and the telecommunications, simulation, instrumentation and VMIC logo are registered trademarks of VMIC. MMX is a control, and process control and monitoring. trademark and Intel and Pentium are registered trademarks of VMISFT-7418 is linked by the user with VxWorks OS, Intel Corporation. Visual Basic, Windows, and Windows NT thus allowing software applications created with Wind River are registered trademarks of Microsoft Corporation. Systems, Inc.’s development system to load and run on the CompactPCI is a registered trademark of PCI Industrial particular VMIC SBC hardware being used. Serial ports, Computer Manufacturers’ Group. BootWare is a registered parallel ports, keyboard, text mode video, and Ethernet are all trademark of Lanworks Technologies, Inc. Other registered supported, as well as floppy and IDE hard disk drives that can trademarks are the property of their respective owners. VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308 3 VMICPCI-7699 Micro- L2 Processor Cache Intel 69000 AGP Pentium II/III Video Embedded Module Controller Host bus Video Connection Ethernet North Bridge Controller DRAM System 10BaseT Controller Intel 82559 100BaseTX C PCI bus P PMC PMC C I South Bridge Embedded PCI-to-ISA, IDE PCI Bridge Accelerator b J3 J5 21554 I/O I/O u (PIIX4) s Comm Port 1 J3 CompactFlash Drive (Optional) Hard PCI-to-EIDE Drive SUPER- I Comm Port 2 J5 I/O S with Flash BIOS A RTC 16-bit Timers Floppy Drive b J3 u 32 Kbyte NVRAM J5 s SMC FDC37C67X Watchdog Timer NVRAM Controller DS1384 PS/2 Keyboard/Mouse Figure 1. VMICPCI-7699 Block Diagram 4 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859