GE Fanuc Automation VMIACC-5595 Specification 2 Gb/s Reflective Memory Hub Assembly Features: • For use with GE Fanuc Embedded Systems’ VMIxxx-5565 Reflective Memory network of products • Provides up to eight ports using small form factor pluggable (SFP) transceivers • Hub assemblies can be cascaded with a maximum of 256 nodes • Automatically bypasses defective or disconnected nodes in a fiber-optic network • Automatic bypass can be optionally controlled by the loss of signal or by the loss of sync pattern • Each port regenerates the serial optical signal, eliminating link losses and reducing jitter • Configurable for use with cables up to 10km in length • 10BaseT Ethernet TCP/IP port for remote access and control • RS232 port for local access and control • Optional 19-inch 1U rack mount or desktop enclosure • Internal universal power supply • Dark on Dark option turns off the board’s transmitter if the receiver does not detect a signal (available for firmware versions 02.00 and later) VMIACC-5595 2Gb/s Reflective Memory Hub Assembly (long distance) transceivers. This feature permits a cost saving in Ordering Options small networks as well as system optimization. For larger May 16, 2007 800-805595-000 E A B C networks, several VMIACC-5595 assemblies can be cascaded, permitting a managed hub array with up to 256 nodes. Each VMIACC-5595 port regenerates the serial optical signal, eliminating the A = Enclosure Options problems with insertion losses and cable attenuation. Signal 0 = Reserved regeneration also reduces jitter. The RS232 port gives you the 1 = Reserved 2 = Rack Mount or Desktop ability to monitor and control your Reflective Memory network B = Number of Single-Mode (10km) Pluggable Transceivers through a simple PC serial port. The Ethernet port feature allows 0, 1, 2, 3, 4, 5, 6, 7, or 8 you to monitor and control the hub from great distances C = Number of Multimode Pluggable Tranceivers through a local area network (LAN) or via a Web browser. 0, 1, 2, 3, 4, 5, 6, 7, or 8 Simplex Cable Specifications As an option, the VMIACC-5595 can be configured as a 19-inch 1U rack-mountable enclosure or as a desktop enclosure. The Fiber-Optic Cable – Multimode 62.5 Micron core universal power supply permits operation with nearly any Fiber-Optic Cable Assemblies A B C international power standard. VMICBL-000-F5 Product Overview ABC = Cable Lengths 000 = 0.5 ft (01.5m) 009 = 200 ft (60.98m) The VMIACC-5595 automatically bypasses ports when the 001 = 1 ft (0.31m) 010 = 250 ft (76.20m) absence of valid synchronization patterns is detected. Three 002 = 5 ft (1.52m) 011 = 350 ft (106.68m) LEDs, adjacent to each port, provide a visual indication of the 003 = 10 ft (3.04m) 012 = 500 ft (152.15m) port status. Additional status indications and modes of 004 = 25 ft (7.62m) 013 = 574 ft (175m) 005 = 50 ft (15.24m) 014 = 656 ft (200m) operation are available through either the serial port or the 006 = 80 ft (24.40m) 016 = 1,000 ft (304.30m) Ethernet port. 008 = 150 ft (45.72m) Duplex Cable Specifications Status information includes the detection of installed transceivers, the detection of signal (light), the detection of valid Fiber-Optic Cable - Multimode; 62.5 Micron core. synchronization patterns and the port operation speed (2Gb/s). Fiber-Optic Cable Assemblies A B C Control registers allow the channel bypass to be based on the absence of a single valid synchronization pattern or multiple VMICBL-000-F6 synchronization patterns. A bypass can also be based simply on ABC = Cable Lengths the loss of a signal (light). In addition, each port can be manually 000 = 3 ft (1m) 011 = 426 ft (130m) forced either active or bypassed regardless of the status 001 = 6 ft (2m) 012 = 492 ft (150m) 002 = 10 ft (3m) 013 = 557 ft (170m) indicators. 003 = 16 ft (5m) 014 = 656 ft (200m) 004 = 32 ft (10m) 015 = 721 ft (220m) An additional control register permits the transmitter of any port 005 = 66 ft (20m) 016 = 754 ft (230m) to be manually disabled. 006 = 98 ft (30m) 017 = 820 ft (250m) 007 = 164 ft (50m) 018 = 885 ft (270m) Front panel manual switches include a recessed momentary 008 = 230 ft (70m 019 = 984 ft (300m) reset switch and a Gang Select switch. The Gang Select switch 009 = 328 ft (100m) 020 = 1 ft (0.3048m) configures the VMIACC-5595 ports as one loop of eight ports or 010 = 393 ft (120m) two separate loops of four ports each. Note The sum of B + C + D Modules should be less or equal to 8. Functional Characteristics For Ordering Information, Call: Multimode Port Wavelength: 830 to 860nm 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 Email: info.embeddedsystems@gefanuc.com Multimode Cable Length: 300m (maximum) Web Address: www.gefanucembedded.com Copyright © 2007 by GE Fanuc Embedded Systems Single-Mode (10km) Port Wavelength: 1,300 to 1,335nm Specifications subject to change without notice. Single-Mode (10km) Cable Length: 10km (maximum) Single-Mode (80km) Port Wavelength: 1,540 to 1,570nm Introduction The VMIACC-5595 is a managed hub designed to operate with Single-Mode (10km) Cable Length: 80km (maximum) the GE Fanuc Embedded Systems’ VMIxxx-5565 family of Dark on Dark: The Dark on Dark option turns off the board’s Reflective Memory real-time network products. The Reflective transmitter if the receiver does not detect a signal (available for Memory hub can automatically bypass ports when it detects a firmware versions 02.00 and later). loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational. Ethernet Controller: 10BaseT interface is compliant with Since the optical ports are implemented with small form factor Transmission Control Protocol/Internet Protocol (TCP/IP) pluggable (SFP) transceivers, only the required ports need to be standards. Each hub assembly will have a unique MAC address. populated. The VMIACC-5595 SFP transceivers can be a The hub assembly can operate on either a LAN or a wide area combination of either multimode (short distance) or single-mode network (WAN). 2 VMIACC-5595 2Gb/s Reflective Memory Hub Assembly The VMIACC-5595 includes a remote user interface available Fuse: 1A, 250V, 5 x 20 mm, fast acting, IEC 60127-2 standard through a standard Ethernet connection. The remote interface is glass or equivalent controlled by the use of standard HTML-based Web browsers. Temperature: The user interface presents status data, such as “loss of signal” Operating: 0° to +65° C and “sync detect” information. Bypass mode, “Dark on Dark’ and Storage: -40° to +85° C the ability to force each port on/off or automatic are supported. Humidity: These settings are retained in NVRAM. Operating: Relative humidity 20% to 80%, noncondensing Storage: Relative humidity 20% to 80%, noncondensing Physical/Environmental Specifications MTBF: Total fit x qty: 2,317.3641 Desktop Assembly Dimensions: 16.73 inches wide by MTBF (hours): 431,524.76 10.0 inches deep by (1U) 1.72 inches high. Dimensions do not include nonskid self-adhesive feet. Regulatory: GE Fanuc Embedded Systems has planned testing of the VMIACC-5595 to meet the following standards, where Rack Mount Assembly Dimensions: The basic dimensions are applicable: the same as the desktop assembly, but include two 1U rack mount brackets for the standard 19-inch rack. European Union (CE Mark) EN55024 Front Panel Connectors: There are eight industry-standard SFP EN55022 Radiated Emissions Class A transceivers. The SFP receptacles not populated with EN55022 Conducted Emissions Class A transceivers contain EMI dust plugs. There is one RJ45 Ethernet EN61000-4-2 (ESD) connector and one 9-pin female D-subminiature RS232 EN61000-4-3 (Radiated Immunity) connector. EN61000-4-4 (EFT) Cabling: Each installed SPF transceiver requires either one EN61000-4-5 (Surge) Duplex LC-type fiber-optic cable or two Simplex LC-type EN61000-4-6 (Conducted RF) fiber-optic cables. The Simplex cables are best suited for EN61000-4-8 (Power Frequency Magnetic Fields) cascading hubs. The Duplex cables can be used for all other United States interconnectivity. FCC Part 15, Class A Rear Panel Connectors: The rear panel contains a power entry Canada module that includes a power ON/OFF switch, a 4A/250V fuse, ICES-003, Class A and a globally accepted IEC receptacle. Power Requirements: Safety: The VMIACC-5595 has been designed to meet the following safety standards where applicable: 90 to 264VAC, 47 to 440Hz, 25W. UL60950 Power supply and power entry module meet safety standards: EN60950(LVD) UL, C-UL: UL 1950 TUV: EN69050 Trademarks CE: EN55022, EN61000-4-2, 3, 4, 5; EN61000-3-2 All registered trademarks are the property of their respective owners. 3 VMIACC-5595 2Gb/s Reflective Memory Hub Assembly Figure 1. VMIACC-5595 Functional Block Diagram 4 VMIACC-5595 2Gb/s Reflective Memory Hub Assembly Figure 2. Example: Cascade of Three VMIACC5595s with 24 Nodes GE Fanuc Embedded Systems Information Centers Additional Resources Americas: For more information, please visit the Huntsville, AL 1 800 322-3616 GE Fanuc Embedded Systems web site at: 1 (256) 880-0444 www.gefanucembedded.com Camarillo, CA 1 (805) 987-9300 Greenville, SC 1 (864) 627-8800 Richardson, TX 1 (972) 671-1972 Europe, Middle East and Africa: Edinburgh, UK 44 (131) 561-3520 Paris, France 33 (1) 4324 6007 5