WT WT WT WT-101 -101 -101 -101, , 101 , , 101 101 101A, A, 102 A, A, 102 102 102 Installation Instructions Hand-Held Wireless Transmitters 1 1 1 1. INTRODUCTION . INTRODUCTION . . INTRODUCTION INTRODUCTION The WT-101 and WT-102 are hand-held wireless transmitters, An LED lights during transmission, powered by a standard 9 VDC battery (Alkaline or Lithium types indicating the battery condition (it preferred). lights if the battery voltage is above 7.5 VDC). If the LED does not light The transmitters are compatible with Visonic Ltd. wireless during transmission, the battery must receivers of the WR-200 and WR-300 series. A system code be replaced immediately. must be selected by setting an 8-position DIP switch and transmission is initiated by depressing the button(s) on the unit. Each unit is fitted with a belt clip. 2 2 2 2. SPECIFICATIONS . SPECIFICATIONS . . SPECIFICATIONS SPECIFICATIONS Operating Frequencies: 315, 404, 418, 433.9 MHz, depending upon country of operation. System Code: 8-bit digital word, 256 combinations, pulse width modulation. Channel Code: 4-bit digital word, pulse width modulation. Compliance with Standards: Meets FCC Part 15, MPT 1340, and Directive 1999/5/EC Power Supply: Standard 9-Volt Battery Current Consumption: 12 mA typical (during transmission only). Figure 1. WT-101, Cover Removed Battery Check: Good battery - LED lights steadily upon transmission. Low battery - LED flickers or doesn't light upon transmission. Operating Temperatures: 0°C to 49°C (32°F to 120°F). Dimensions (H x W x D): 108 x 35 x 26 mm (4-1/4 x 1-3/8 x 1in.) Weight (excluding battery): Approximately 35 gr (1.2 oz) Attention: Transmitter characteristics may be affected by battery condition. MODEL VARIATIONS Figure 2. WT-101A, Cover Removed Model WT-101 (see Fig. 1): This model activates the receiver's "channel 1" output relay. Model WT-101A (see Fig. 2): This model can be programmed to activate any one of the 4 output relays in the receiver - from "channel 1" to "channel 4". FCC ID: GSAWT101A; CANADA: 1467 202 271A Model WT-102 (see Fig. 3): The gray button activates the receiver's "channel 1" output relay, and the red button activates "channel 2" output relay. FCC ID: GSAWT102A; CANADA: 6515 1467 K694 Figure 3. WT-102, Cover Removed 3 3 3 3. INSTALLATION . INSTALLATION . . INSTALLATION INSTALLATION 3.1 Connecting the Battery 3.2 Selecting the System Code All models have an 8-position DIP A. Remove the screw and the switch (marked 1 - 8, see Fig. 5). Each belt clip at the back of the switch may be set to ON or OFF, unit (see Figure 4). creating a unique digital system code. B. Position the transmitter with Use a ball-point pen to set each of the the front side up and detach switches to match the code setting of the front cover from the the target receiver. Figure 5. Code Selector base. CAUTION: The code combination 2, 4, 5, 6, 7 ON and 1, 3, 8 C. Install the battery clip onto OFF (as shown in Figure 5) is a factory test code that should be the 9-Volt battery. Position avoided. Also do not select "easy" codes such as all keys ON, the battery as shown in Figure 4. Screw and Belt Clip all keys OFF or alternating ON/OFF settings. Figures 1, 2 and 3. DE2031 1 3.3 Setting the Channel Code (WT-101A only) B. Stand 3 meters (10 feet) away from the receiver and operate the transmitter. The WT-101A transmitter is equipped with a 4-position C. Verify that the transmitter LED lights, indicating good battery DIP-switch marked CHANNEL condition. (Fig. 6) that serves as a channel D. Observe that the receiver LED lights, indicating detection of selector. By means of this the transmitted RF signal. switch, the transmitter can be E. Make sure that the expected end result is obtained: programmed to activate one of 4 Figure 6. Channel Selector outputs at the receiver. WT-101: Verify activation of the "channel 1" output relay at the receiver. This feature is important for zoning purposes – activating different alarm zones of a control panel via a multi-output receiver. The WT-101A: Verify activation of the desired output relay at the channel data transmitted by the WT-101A is selected by setting receiver, according to the channel selected. the switch with the desired channel number to ON. Use a ball WT-102: Verify that the transmitter gray pushbutton activates point pen to set the channel selector as required. the receiver's "channel 1" output relay and that the red pushbutton activates the receiver's "channel 2" output relay. 3.4 Assembly and Testing F. Operate the transmitter at various locations within the A. Carefully position the front cover in place, press it against the reception range to determine "dead" spots, where base and turn the unit with its back up. Position the belt clip transmission may be blocked. as shown in Figure 4 and re-insert the screw. 4. 4. MISCELLANEOUS MISCELLANEOUS COMMENTS COMMENTS 4 4. . MISCELLANEOUS COMMENTS MISCELLANEOUS COMMENTS The 315 MHz model of this device complies with Part 15 of the 4.1 Product Limitations FCC Rules and RSS-210 of Industry and Science Canada. Visonic Ltd. wireless systems are very reliable and are tested to Operation is subject to the following two conditions: (1) This high standards. However, due to their low transmitting power and device may not cause harmful interference, and (2) this device limited range (required by FCC and other regulatory authorities), must accept any interference that may be received, including there are some limitations to be considered: interference that may cause undesired operation. A. Receivers may be blocked by radio signals occurring on or near The user is cautioned that changes or modifications to the their operating frequencies, regardless of the code selected. unit, not expressly approved by Visonic Ltd., could void the B. A receiver can only respond to one transmitter signal at a time. user's FCC authority to operate the equipment. C. Wireless equipment must be tested regularly to reveal sources of interference and to protect against faults. 4.3 Frequency Allocations for Wireless Devices in European (EU) Countries 4.2 Compliance with Standards • 433.92 MHz has no restriction in any EU member state. This device complies with the essential requirements and provisions • 418 MHz is allowed in the UK only. of Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio and telecommunications terminal equipment. • 315 MHz is not allowed in any EU member state WARRANTY WARRANTY WARRANTY WARRANTY Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its The Manufacturer does not represent that its Product may not be compromised and/or products hereinafter referred to as "the Product" or "Products" to be in conformance with circumvented, or that the Product will prevent any death, personal and/or bodily injury its own plans and specifications and to be free of defects in materials and workmanship and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the under normal use and service for a period of twelve months from the date of shipment by Product will in all cases provide adequate warning or protection. User understands that a the Manufacturer. The Manufacturer's obligations shall be limited within the warranty properly installed and maintained alarm may only reduce the risk of events such as period, at its option, to repair or replace the product or any part thereof. The Manufacturer burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such shall not be responsible for dismantling and/or reinstallation charges. To exercise the will not occur or that there will be no death, personal damage and/or damage to property warranty the product must be returned to the Manufacturer freight prepaid and insured. as a result. This warranty does not apply in the following cases: improper installation, misuse, The Manufacturer shall have no liability for any death, personal and/or bodily injury failure to follow installation and operating instructions, alteration, abuse, accident or and/or damage to property or other loss whether direct, indirect, incidental, tampering, and repair by anyone other than the Manufacturer. consequential or otherwise, based on a claim that the Product failed to function. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or This warranty is exclusive and expressly in lieu of all other warranties, obligations or damage arising under this limited warranty or otherwise, regardless of cause or origin, the liabilities, whether written, oral, express or implied, including any warranty of Manufacturer's maximum liability shall not in any case exceed the purchase price of the merchantability or fitness for a particular purpose, or otherwise. In no case shall the Product, which shall be fixed as liquidated damages and not as a penalty, and shall be the Manufacturer be liable to anyone for any consequential or incidental damages for breach complete and exclusive remedy against the Manufacturer. of this warranty or any other warranties whatsoever, as aforesaid. Warning: The user should follow the installation and operation instructions and among This warranty shall not be modified, varied or extended, and the Manufacturer does not other things test the Product and the whole system at least once a week. For various authorize any person to act on its behalf in the modification, variation or extension of this reasons, including, but not limited to, changes in environmental conditions, electric or warranty. This warranty shall apply to the Product only. All products, accessories or electronic disruptions and tampering, the Product may not perform as expected. The user attachments of others used in conjunction with the Product, including batteries, shall be is advised to take all necessary precautions for his /her safety and the protection of covered solely by their own warranty, if any. The Manufacturer shall not be liable for any his/her property. damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction of the Product due to products, accessories, or 6/91 attachments of others, including batteries, used in conjunction with the Products. VISONIC LTD (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094 VISONIC LTD. (UK): FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 730-0800 FAX: (0870) 730-0801 INTERNET: www.visonic.com VISONIC LTD. 2001 WT-101/102 DE2031- (REV. 5, 7/01) 2 DE2031