MKP 336 1 X1 Vishay BCcomponents Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 16 168 8x x12(halfpage) 12(halfpage) w l 15 to 27.5 mm lead pitch. Supplied loose in box, taped on reel Lead (Pb)-free product e3 RoHS-compliant product RoHS h COMPLIANT RATED VOLTAGE AC 275 V; 50 to 60 Hz l t PERMISSIBLE DC VOLTAGE DC 630 V P ± 0.4 Ø d t Dimensions in mm ENCAPSULATION Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 NO FOCUS PRODUCT: USE MKP 3381 X1 APPLICATIONS CLIMATIC TESTING CLASS ACC. TO EN 60068-1 X1 class 55/105/56/B For X1 electromagnetic interference suppression in across the line applications (50/60 Hz) with a maximum mains voltage of 275 V(AC) CAPACITANCE RANGE (E12 SERIES) For application limitations please refer to section E12 series 0.01 to 1 µF “Application notes” Preferred values acc. to E6 REFERENCE STANDARDS CAPACITANCE TOLERANCE “IEC 60384-14 2nd edition and EN 132400” ± 20 %; ± 10 %; ± 5 % “IEC 60065, pass. flamm. class B” 250 V: CSA-C22.2 No 1; UL1414 275 V: UL1283; ENEC LEADS Tinned wire MARKING C-value; tolerance; rated voltage; sub-class; manufacturer’s RATED TEMPERATURE type designation; code for dielectric material, only for pitch ≥ 15 mm; manufacturer location; year and week 105 °C DIELECTRIC MAXIMUM APPLICATION TEMPERATURE Polypropylene film 105 °C ELECTRODES DETAIL SPECIFICATION Metallized film For more detailed data and test requirements contact: rfi@vishay.com CONSTRUCTION Mono construction www.vishay.com For technical questions contact: rfi@vishay.com Document Number: 28117 170 Revision: 15-Feb-08 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type COMPOSITION OF CATALOG NUMBER TYPE AND PITCHES MULTIPLIER 15.0 mm (nF) 336 1 X1 22.5 mm 0.1 2 CAPACITANCE 27.5 mm 1 3 (numerically) 10 4 100 5 Example: 104 = 10 x 10 = 100 nF BFC2 336 1X XX X 2222(*) 336 1X XX X (*) Old ordering code TYPE PACKAGING LEAD CONFIGURATION C-TOL PREFERRED TYPES 336 1 lead length 3.5 ± 0.3 mm BFC2 336 10... loose in box lead length 25.0 ± 2.0 mm BFC2 336 16... X1 ± 20 % ON REQUEST lead length 3.5 ± 0.3 mm BFC2 336 11... loose in box ± 10 % 336 1 lead length 25.0 ± 2.0 mm BFC2 336 17... ± 20 % BFC2 336 13... X1 H = 18.5 mm; P = 12.7 mm; 0 taped on reel reel diameter 500 mm ±10 % BFC2 336 14... Note (1) For detailed tape specifications refer to Packaging information www.vishay.com/docs/28139/packinfo.pdf SPECIFIC REFERENCE DATA MKP 336 1 275 VAC DESCRIPTION VALUE Tangent of loss angle: at 10 kHz -4 C ≤ 100 nF ≤ 10 x 10 100 nF < C ≤ 470 nF -4 ≤ 20 x 10 C > 470 nF -4 ≤ 70 x 10 Rated voltage pulse slope (dU/dt) at 385 V (DC): R P=15mm 250 V/µs P = 22.5 mm 150 V/µs P = 27.5 mm 100 V/µs R between leads, for C ≤ 0.33 µF at 100 V; 1 min > 15 000 MΩ RC between leads, for C > 0.33 µF at 100 V; 1 min > 5000 s R between leads and case; 100 V; 1 min > 30 000 MΩ Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 3400 V; 1 min Withstanding (AC) voltage between leads and case 2050 V; 1 min Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 171 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type MKP 336 1 GENERAL DATA U = 275 V; C-tol = ± 20 % Rac CATALOG NUMBER BFC2 336 1 ..... AND PACKAGING LOOSE IN BOX REEL DIMENSIONS C MASS Wx Hx L (1) l = 3.5 ± 0.3 l = 25.0 ± 2.0mm H = 18.5 mm; P = 12.7 mm t t 0 (µF) (g (mm) Last 5 digits of Last 5 digits of Last 5 digits of SPQ SPQ SPQ catalog number catalog number catalog number Pitch = 15.0 ± 0.4 mm; d = 0.6 ± 0.06 mm t 0.01 19001 19007 19002 0.015 5.0 x 11.0 x 17.5 1 10153 16153 13153 1100 1000 1000 0.022 10223 16223 13223 0.033 6.0 x 12.0 x 17.5 1.4 10333 16333 13333 900 Pitch = 15.0 ± 0.4 mm; dt = 0.8 ± 0.08 mm 0.047 7.0 x 13.5 x 17.5 1.8 10473 16473 13473 800 1000 0.068 8.5 x 15.0 x 17.5 2.4 10683 16683 500 13683 650 0.1 10.0 x 16.5 x 17.5 3 10104 500 16104 13104 600 Pitch = 22.5 ± 0.4 mm; dt = 0.8 ± 0.08 mm 0.1 7.0 x 16.5 x 26.0 2.9 19003 19008 19004 550 0.15 8.5 x 18.0 x 26.0 3.8 10154 200 16154 500 13154 450 0.22 10.0 x 19.5 x 26.0 6.8 10224 16224 13224 400 Pitch = 27.5 ± 0.4 mm; dt = 0.8 ± 0.08 mm 0.22 11.0 x 21.0 x31.0 7.4 19005 19009 0.33 13.0 x 23.0 x 31.0 9.2 10334 16334 100 125 0.47 15.0 x 25.0 x 31.0 12.3 10474 16474 0.68 18.0 x 28.0 x 31.0 16.1 10684 16684 1 21.0 x 31.0 x 31.0 20.3 10105 50 16105 75 Notes 1. Weight for short lead product only www.vishay.com For technical questions contact: rfi@vishay.com Document Number: 28117 172 Revision: 15-Feb-08 MKP 336 1 X1 Interference Suppression Film Vishay BCcomponents Capacitors U = 275 V; C-TOL = ± 10 % RAC CATALOG NUMBER BFC2 336 1..... AND PACKAGING DIMENSIONS LOOSE IN BOX REEL C MASS Wx Hx L (1) (µF) (g) lt = 3.5 ± 0.3 m lt = 25.0 ± 2.0 mm H = 18.5 mm; P = 12.7 mm 0 (mm) last 5 digits SPQ last 5 digits SPQ last 5 digits SPQ Pitch = 15.0 ± 0.4 mm; d = 0.6 ± 0.06 mm t 0.01 11103 17103 14103 0.012 11123 17123 14123 5.0 x 11.0 x 17.5 1 1100 0.015 11153 17153 14153 1000 1000 0.018 11183 17183 14183 0.022 11223 17223 14223 6.0 x 12.0 x 17.5 1.4 900 0.027 11273 17273 14273 Pitch = 15.0 ± 0.4 mm; dt = 0.8 ± 0.08 mm 0.033 11333 17333 14333 7.0 x 13.5 x 17.5 1.8 800 0.039 11393 17393 14393 1000 0.047 11473 17473 14473 8.5 x 15.0 x 17.5 2.4 500 650 0.056 11563 17563 14563 0.068 11683 17683 14683 10.0 x 16.5 x 17.5 3 500 600 0.082 11823 17823 14823 Pitch = 22.5 ± 0.4 mm; dt = 0.8 ± 0.08 mm 0.1 7.0 x 16.5 x 26.0 2.9 11104 17104 500 14104 550 0.12 11124 17124 14124 8.5 x 18.0 x 26.0 3.8 200 250 450 0.15 11154 17154 14154 0.18 10.0 x 19.5 x 26.0 6.8 11184 17184 500 14184 400 Pitch = 27.5 ± 0.4 mm; dt = 0.8 ± 0.08 m 0.22 11224 17224 11.0 x 21.0 x 31.0 7.4 0.27 11274 17274 0.33 13.0 x 23.0 x 31.0 9.2 11334 17334 0.39 11394 100 17394 125 15.0 x 25.0 x 31.0 12.3 0.47 11474 17474 0.56 11564 17564 18.0 x 28.0 x 31.0 16.1 0.68 11684 17684 0.82 21.0 x 31.0 x 31.0 20.3 11824 50 17824 75 Note 1. Weight for short lead product only Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 173 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type SAFETY APPROVALS X1 VOLTAGE VALUE FILE NUMBERS EN132400 275 V (AC) 10 nF to 1 µF FI 2006020 UL1414 250 V (AC) 10 nF to 1 µF E112471 UL1283 275V (AC) 10 nF to 1 µF E109565 CSA-C22.2 No.1 250 V (AC) 10 nF to 1 µF 1104860 The Enec-approval together with the CB-Certificate replace all national marks of the following countries (they have already signed the ENEC-Agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg; Netherlands; Norway; Portugal; Slovenian; Spain; Switzerland and United Kingdom. ® 16 MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic b = b + 0.3 mm insertion machines. max For detailed tape specifications refer to eccentricity “Packaging information”. Specific Method of Mounting to Withstand Vibration and l = I + 0.3 mm max Shock CBA116 In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board: • For pitches ≤ 15 mm capacitors shall be mechanicelly fixed by the leads Storage Temperature • For longer pitches the capacitors shall be mounted in the • Storage temperature: T = 25 to + 40 °C with RH stg same way and the body clamped maximum 80 % without condensation Space Requirements on printed Circuit Board Ratings and Characteristics Reference Conditions The maximum length and width of film capacitors is shown in Unless otherwise specified, all electrical values apply to an Figure: ambient temperature of 23 ± 1 °C, an atmospheric pressure • Eccentricity as in figure. The maximum eccentricity is of 86 to 106 kPa and a relative humidity of 50 ± 2 %. smaller than or equal to the lead diameter of the product For reference testing, a conditioning period shall be applied concerned over 96 ± 4 hours by heating the products in a circulating air • Product height with seating plane as given by “IEC 60717” oven at the rated temperature and a relative humidity not as reference: h ≤ h + 0.3 mm exceeding 20 %. max www.vishay.com For technical questions contact: rfi@vishay.com Document Number: 28117 174 Revision: 15-Feb-08 X1 1 nF 4.7 nF 10 nF 100 nF 470 nF 1000 nF 47 nF MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type CHARACTERISTICS Capacitance Tangent of loss angle 3 4 10 2 typical 2 10 0 max. - 2 1 10 - 4 min. 0 - 6 10 100 - 50 050 1 2 3 4 5 10 10 10 10 10 Tamb (°C) f (Hz) Resonant frequency Impedance 2 3 10 10 1 10 1 10 0 10 0 10 -1 10 -2 -1 10 10 4 5 6 7 10 10 10 10 f (Hz) 10 1 10 100 1000 10 000 C (nF) Max RMS voltage and AC current (sinewave) 3 4 10 10 1000 nF 470 nF 2 10 100 nF 2 10 47 nF 1 10 10 nF 4.7 nF 0 10 1 nF T ≤ 105 °C T ≤ 100 °C amb amb -1 1 10 10 5 1 2 3 4 5 1 2 3 4 f (Hz) 10 10 10 10 10 10 10 10 10 f (Hz) 10 Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 175 C ≤ 10 nF 10 nF < C ≤ 47 nF 47 nF < C ≤ 220 nF 220 nF < C < 1 µF C = 1 µF Impedance AC voltage DC/C (Ω) (V) (%) Dissipation -4 f (MHz) AC current factor (x 10 ) (mA) MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type CHARACTERISTICS Capacitance 6 10 5 10 4 10 0 20 40 60 80 100 Tamb (°C) APPLICATION NOTES • For X1 electromagnetic interference suppression in across the line applications (50/60 Hz) with a maximum mains voltage of 275 V (AC). • These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse programs must be used. • These capacitors are not intended for series impedance application. For these situations in case safety approvals are requested, please refer to our special capacitors of 1772 series with internal series connection. • The maximum ambient temperature must not exceed 105 °C. • Rated voltage pulse slope: If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 385 V (DC) and divided by the applied voltage. Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 176 RC (s) MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type INSPECTION REQUIREMENTS General Notes: 1. Sub-clause numbers of tests and performance requirements refer to the “ Sectional Specification, IEC-puplication EN 132400 (IEC 60384-14) and section One of this specification”. 2. In this table: D = destructive ND = non destructive Group C inspection requirements D SUB - CLAUSE NUMBER OR CONDITIONS PERFORMANCE REQUIREMENTS AND TEST ND SUB-GROUP C1A PART OF SAMPLE D OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in Chapters “General data” of this specification Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz For C > 470 nF at 10 kHz 4.3 Robustness of Tensile: load 10 N; 10 s No visible damage terminations Bending: load 5 N; 4 x 90° 4.4 Resistance to soldering heat No pre-drying Method: 1A Solder bath: 260 °C Duration: 10 s 4.19 Component solvent Isopropylalcohol at room temperature resistance Method: 2 Immersion time: 5 ± 0.5 min Recovery time: Min. 1 hour, max. 2 hours 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured initially Tangent of loss angle Increase of tan δ: ≤ 0.0100 for: C ≤ 100 nF or ≤ 0.0200 for: 100 nF < C ≤ 470 nF or ≤ 0.0080 for: C > 470 nF Compared to values measured initially Insulation resistance As specified in Section “Insulation Resistance” of this specification Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 177 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type D SUB - CLAUSE NUMBER OR CONDITIONS PERFORMANCE REQUIREMENTS AND TEST ND SUB - GROUP C1B PART OF SAMPLE D OF SUB - GROUP C1 Initial measurements No visible damage Capacitance Legible marking Tangent of loss angle: For C ≤ 470 nF at 100 kHz For C > 470 nF at 10 kHz 4.20 Solvent resistance of the marking: No visible damage Isopropylalcohol at room temperature see Section “General notes”; item 5 Method: 1 Rubbing material: cotton wool Immersion time: 5 ± 0.5 min 4.6 Rapid change of temperature θA = - 55 °C θB = + 105 °C 5 cycles 4.6.1 Inspection Duration t = 30 min 4.7 Vibration (see note 3.1) Visual examination Mounting: see Section “Mounting” of this specification Procedure B4: Frequency range: 10 to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s² No visible damage (whichever is less severe) Total duration 6 hours 4.7.2 Final inspection Visual examination No visible damage 4.9 Shock (see note 3) Mounting: see Section “Mounting” for more information Pulse shape: half sine Acceleration: 490 m/s² Duration of pulse: 11 ms 4.9.2 Final measurements Visual examination No visible damage Capacitance |ΔC/C| ≤ 5 % of the value measured initially Tangent of loss angle Increase of tan δ: ≤ 0.0100 for: C ≤ 100 nF or ≤ 0.0200 for: 100 nF < C ≤ 470 nF or ≤ 0.0080 for: C > 470 nF Compared to values measured initially Insulation resistance As specified in Section “Insulation Resistance” of this specification Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 178 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type D SUB - CLAUSE NUMBER OR CONDITIONS PERFORMANCE REQUIREMENTS AND TEST ND SUB - GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB - D GROUPS C1A AND C1B 4.11 Climatic sequence 4.11.1 Initial measurements Capacitance Measured in 4.4.2 and 4.9.2 Tangent of loss angle: Measured initially in C1A and C1B 4.11.2 Dry heat Temperature: 105 °C Duration: 16 hours 4.11.3 Damp heat cyclic Test Db 4.11.4 Cold Temperature: - 55 °C Duration: 2 hours 4.11.5 Damp heat cyclic Test Db 4.11.6 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan δ: ≤ 0.0100 for: C ≤ 100 nF or ≤ 0.0200 for: 100 nF < C ≤ 470 nF or ≤ 0.0080 for: C > 470 nF Compared to values measured in 4.11.1 Voltage proof No permanent breakdown or flash-over 1200 V (DC); 1 min between term. Insulation resistance ≥ 50 % of values specified in Section “Insulation resistance” of this specification SUB - GROUP C2 D 4.12 Damp heat steady state 56 days, 40 °C, 90 to 95 % RH, no load Capacitance 4.12.1 Initial measurements Tangent of loss angle at 10 kHz 4.12.3 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.12.1. Tangent of loss angle Increase of tan δ: ≤ 0.0080 Compared to values measured in 4.12.1. Voltage proof No permanent breakdown or flash-over 1200 V (DC); 1 min between term. Insulation resistance ≥ 50 % of values specified in Section “Insulation resistance” of this specification Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 179 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type D SUB - CLAUSE NUMBER OR CONDITIONS PERFORMANCE REQUIREMENTS AND TEST ND SUB GROUP C3 D 4.13.1 Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz For C > 470 nF at 10 kHz 4.13 Impulse voltage 3 successive impulses, full wave, peak No selfhealing breakdowns or flashover voltage: X1: 4 kV Max. 24 pulses 4.14 Endurance Duration: 1000 hours 1.25 U at 105 °C Rac Once in every hour the voltage is increased to 1000 V (RMS) for 0.1 s via resistor of 47 Ω ± 5 % 4.14.7 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 10 % compared to values measured in 4.13.1. Tangent of loss angle Increase of tan δ: ≤ 0.0100 for: C ≤ 100 nF or ≤ 0.0200 for: 100 nF < C ≤ 470 nF or ≤ 0.0080 for: C > 470 nF Compared to values measured in 4.13.1. Voltage proof No permanent breakdown or flash-over 1200 V (DC); 1 min between terminations. 2050 V (DC); 1 min between terminations and case. Insulation resistance ≥ 50 % of values specified in Section “Insulation resistance” of this specification SUB - GROUP C 4 D 4.15 Charge and discharge 10 000 cycles (50 c/s) charge to UR half sinewave Duration: 5 ms Discharge resistance: 385 Vdc R = - ----- ------ ----- ----- ------ ----- ----- ----- ------ - - 1.5 × C() () dU ⁄() dt R = 2.2 min 4.15.1 Initial measurements Capacitance Tangent of loss angle For C ≤ 470 nF at 100 kHz For C > 470 nF at 10 kHz 4.15.3 Final measurements Capacitance |ΔC/C| ≤ 10 % compared to values measured in 4.15.1. Tangent of loss angle Increase of tan d: ≤ 0.0100 for: C £ 100 nF or ≤ 0.0200 for: 100 nF < C £ 470 nF or ≤ 0.0080 for: C > 470 nF Compared to values measured in 4.15.1 Insulation resistance ≥ 50 % of values specified in Section “Insulation resistance” of this specification Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 180 MKP 336 1 X1 Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type D SUB - CLAUSE NUMBER OR CONDITIONS PERFORMANCE REQUIREMENTS AND TEST ND SUB - GROUP C5 D 4.16 Radio frequency characteristic Resonance frequency As specified in Section “Resonant frequency” of this specification. ± 10 % SUB - GROUP C6 D 4.17 Passive flammability Bore of gas jet: Ø 0.5 mm After removing test flame from capacitor, Class B Fuel: butane the capacitor must not continue to burn Test duration for actual volume V in mm³: for more than 10 s. No burning particle V ≤ 250: 10 s must drop from the sample. 250 < V ≤ 500: 20 s 500 < V ≤ 1750: 30 s V > 1750: 60 s One flame application 12 mm ~ 8 mm 45.0 ° SUB - GROUP C7 D 4.18 Active flammability 20 x 4 kV discharges on the test The cheese cloth around the capacitors capacitor connected to UR shall not burn with a flame. No electrical measurements are required. Document Number: 28117 For technical questions contact: rfi@vishay.com www.vishay.com Revision: 15-Feb-08 181 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 www.vishay.com Revision: 18-Jul-08 1