Issue 10 (540) 563-2000 PAGING HORNS SX15-T, SX15-TM, SX30-T, SX30-8, SX15-8 SX15-TM SX15-8 SX15-T SX30-8 SX30-T INTRODUCTION SPECIFICATIONS The SX15-T, SX15-TM, SX15-8, SX30-T and SX30-8 Product Description are Paging Horns for use with any Clarity - SX15-T 25/70/100V 15 Watt Paging Horn Mixer-Amplifier. - SX15-TM 25/70/100V 15 Watt Paging Horn (Marine Version - Sealed) The SX15-T is a 15 Watt horn, the SX15-TM is a 15 - SX30-T 25/70/100V 30 Watt Paging Horn Watt horn designed for nautical use and the SX30-T - SX15-8 8 Ohm 15 Watt Paging Horn is a 30 Watt horn, all containing a line matching - SX30-8 8 Ohm 30 Watt Paging Horn transformer. The SX15-8 is a 15 Watt, 8 Ohm paging horn, the SX30-8 is a 30 Watt, 8 Ohm paging horn. Applications These horns can be used for interior or exterior - Clarity Paging Systems paging applications. - Existing 8 Ohm or 25, 70 or 100 Volt Paging Systems These instructions contain the specifications and information necessary to install, operate and maintain the horns. 1 947432 SPL @ 4 feet at 1 Watt at 1K Features SX15-T 105dB - Combination 25/70/100V transformer (SX15-T, SX15-TM 105dB SX30-T, SX15-TM) SX15-8 105dB - Weather resistant construction SX30-T 107dB - High impact plastic housing in beige, gray or SX30-8 107dB white housing - Marine version - no fade, white sealed housing - Fully adjustable 360 degrees horizontal and 90 Line Voltage degrees vertical · 25/70/100V (SX15-T, SX15-TM, SX30-T) - Rotary switch for tap selection · 8 Ohms (SX15-8, SX30-8) - Stainless steel hardware - Beam mount clamp or electrical backbox INSTALLATION Cabling Environment Standard two conductor shielded cable (18-20AWG) - Temperature: 0 to +50 Degrees C can be used for connections. - Humidity: 0 to 85% Connections Horn Taps for the SX15-T, SX15-TM Connect station or other suitable wire to leads as 15 Watts, 25/70/100 Volts follows: Switch Setting 100V 70V 25V Set Ohms Page Out.......................................Tip 1.9 - - 1 5333 Control Common........................... Ring 3.8 1.9 - 2 2667 Unit 7.5 3.8 - 3 1333 15 7.5 - 4 667 - 15 1.9 5 333 Attaching Speaker to Base - - 3.8 6 167 NOTE: For ease of installation, the base can be - - 7.5 7 83 attached to the speaker before or after the base is - - 15 8 42 mounted. · Loosen position adjustment knob. Horn Taps for the SX30-T · Insert the ball of the base into the socket of the 30 Watts, 25/70/100 Volts speaker. Switch Setting · Tighten the position adjustment knob. 100V 70V 25V Set Ohms 1.9 - - 1 5333 3.8 1.9 - 2 2667 Mounting/Positioning 7.5 3.8 - 3 1333 Mount the horn to a suitable surface using the 15 7.5 - 4 667 hardware provided. These units can be mounted to a 30 15 1.9 5 333 wall, a beam or an electrical box. - 30 3.8 6 167 - - 7.5 7 83 · Mount the base to a wall using the two holes - - 15 8 42 provided. Knockout holes are provided for - - 30 9 21 punch out should additional holes be required. · A "C" clamp is provided with the horns to allow Specifications mounting to a beam. Place the bolt through the Frequency Response and Maximum Power hole in the bottom of the base to secure the "C" Handling Capability clamp to the beam (See Figure 1). SX15-T 300 - 10K 15 Watts SX15-TM 300 - 10K 15 Watts SX15-8 300 - 10K 15 Watts SX30-T 300 - 10K 30 Watts SX30-8 300 - 10K 30 Watts 2 · Connection to an electrical backbox is TECHNICAL ASSISTANCE accomplished by channeling wire through the When trouble is reported, verify there are no broken ball of the base (See Figure 2) and making connections leading to the unit. appropriate connections. The base has holes punched for a double-gang square box, but by Assistance in troubleshooting is available from the punching out additional knockout holes, the base factory. When calling, you should have a VOM can be mounted to a single-gang or octagon box. available and be calling from the job site. Call (540) 563-2000 and ask for Technical Support or (540) The horns may be rotated or moved up and down to 767-1555 for Clarity 24-hour Faxback System. Visit our obtain the desired position by loosening the knob at website at http://www.clarity-com.com the bottom of the unit, approximately 1 turn. Make required adjustments and re-tighten knob. Clarity equipment is not field repairable. Clarity maintains service facilities in Roanoke, VA. Should repairs be necessary, attach a tag to the unit clearly stating your company name, address, phone number, contact person and the nature of the problem. Send the unit to: Clarity Repair and Return Dept. 5614 Hollins Road Roanoke, VA 24019-5056 LIMITED WARRANTY Clarity warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for a period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or refund of any such defective device within the warranty period, provided that: 1. inspection by Clarity indicates the validity of the claim; 2. the defect is not the result of damage, misuse or negligence after the original shipment; 3. the product has not been in any way repaired by others and that factory sealed units are unopened (A service charge plus parts and labor will be applied to units defaced or physically damaged); 4. freight charges for the return of products to Clarity are prepaid; 5. all units “out of warranty” are subject to a service charge. The service charge will cover minor repairs (Major repairs will be subject to additional charges for parts and labor). This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Clarity be liable for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation or use of the product. This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point. 3 I-Beam "C" Clamp Speaker Base Position Adjustment Knob Figure 1 - Mounting to a Beam with a "C" Clamp Electrical Backbox Wire Position Speaker Adjustment Base Knob Figure 2 - Mounting to an Electrical Backbox 4