Call U.S.: (954) 346-2442 • sales@unipower-corp.com Call U.K.: +44(0) 1903 768200 • info@unipower-europe.com CORPORA TION ® PowerCassette : 1U HIGH RACK-MOUNT DC/DC CONVERTERS 48VDC to 12 or 24VDC at 700 Watts with Hot Swap FEATURES Isolated 5V, ¼ A Standby Output Hot-Swap Operation 12 or 24 VDC Output Up to 2100 Watts System Output Remote Output Adjustment Wide Range 40 to 60VDC Input Integral LED Status Indicators 0 0 TPCMQ48 Series -20 C to +70 C Operating 1U High 2 1.6” x 5” x 10” I C Serial Data Bus Option (41 x 127 x 254 mm) Up to 8.8 Watts/Cubic Inch Power Density Low ProŢ le: 1.6 Inches High Single Hot-Swappable Connector Reverse Air Flow Option Staged Pin Engagement ORing Diode on Output Three-Unit Rack/Shelf 1U, 19” Rack/Shelf Holds 3 Units TPCMQR1U3-48 19- or 23-Inch Rack Mounting Active Current Sharing Optimized Thermal Management LVD73/23/EEC TWO-YEAR WARRANTY No Minimum Load Patent Protected Control & Monitoring Features STANDARD MODULES MAX. OUTPUT OUTPUT OUTPUT INPUT MODEL POWER VOLTAGE CURRENT VOLTAGE NUMBER 650W 12VDC 54.2A 40-60VDC TPCMQ48-12/54 650W 13.6VDC 47.8A 40-60VDC TPCMQ48-13/48 700W 24VDC 29.2A 40-60VDC TPCMQ48-24/29 700W 27.2VDC 25.7A 40-60VDC TPCMQ48-27/26 NOTE: The table does not show the independent 5V, ¼A standby output which is standard on all models. SYSTEM RACK/SHELF (See Page 3) NO. OF MODEL WIDTH HEIGHT MODULES TPCMQR1U3-48 19” (483 mm) 1.72” (43.7 mm) 3 NOTE: System rack and hot-swap modules must be ordered separately. Brackets are available for mounting the 19-inch rack/shelf. OPTIONS SAFETY STANDARDS OUTPUT CODE DESCRIPTION DERATING UL60950-1 CSA22.2, No. 60950-1 R Reverse Air Flow (Back to Front) 20% EN60950-1 2 ZI C Serial Data Bus N/A NOTE: Add Option Code as sufŢ x to model no. on both module and rack/shelf. Contact factory on availability of Option Z. www.unipowercorp.com or www.powercassette.com Copyright © 2008-2011 Unipower Corporation. All rights reserved. CORPORA TION SPECIFICATIONS, TPCMQ48 SERIES DC/DC CONVERTERS o Typical at Nominal 24VDC Input, Full Load and 25 C Unless Otherwise Noted. OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS 4 Total Output Power, Continuous, Max. ............ 650-700 Watts EfŢ ciency ) ........................................... 82-88% at Full Load Voltage Adjustment Range, Min. ......................-25% to +10% Switching Frequency, ................................. 210kHz Nominal 1 5 Total Regulation .............................................................2.0% Isolation, Class I, min. Total Regulation, Standby Supply ...................................5.0% Input-Output ...................................................... 2121VDC 2 Ripple & Noise, Pk-Pk ) .............................................. 200mV Input-Ground .................................................... 1000VDC Voice Band Noise ................................................... <32dBrnC Output-Ground .................................................... 100VDC 3 Dynamic Response ) .................................................. 300μS MTBF (Bellcore) ............................................. 200,000 Hours Temperature CoefŢ cient ......................................±0.02%/°C Safety Standards.. ...... EN60950, UL1950, CSA22.2 No.950 Minimum Load .....................................................................0A ENVIRONMENTAL SPECIFICATIONS Current Limit ...........................................105% Rated Current o Operating Temperature .......................-20°C to 70 C Ambient Overload Protection ......................................... Auto Recovery o o o Derating ............................................ 2.5% / C, 50 C to 70 C Overvoltage Protection ..............................Latched Shutdown o o Storage Temperature ......................................-40 C to +85 C Remote Sense .......................................Up to 0.25V Per Wire Cooling ......................................... Integral Ball Bearing Fans Current Share ..................................... ±10% Full Load Rating Standby Output.................................................... +5V, 250mA PHYSICAL SPECIFICATIONS Output Power Good Signal ......................................Logic Low Case Material, Module & Rack/Shelf ......................Aluminum Input Power Fail Signal....................................... Logic High Dimensions, Inches(mm), Module ......1.6 H x 5.0 W x 10.0 D Inhibit .......................................................................Logic Low (40.6 x 127 x 254) Enable .....................................................................Logic Low Rack/Shelf ......................1.72H x 19.00 W x 11.56 D Thermal Warning ....................................................Logic High (44 x 483 x 294) Weight, Module .........................................3.15 lbs. (1.43 kg.) INPUT SPECIFICATIONS Rack/Shelf ...................................4.15 lbs. (1.88 kg.) Input Voltage Range ...............................................40-60VDC Inrush Current Limiting ............................................ 10A Peak NOTES: 1. No load to full load, including line regulation and load regulation. Input EMI Filter ....................................................... Standard 2. Whichever is greater. 20MHz bandwidth. Measure with 0.1μF ceramic and 10μF tantalum capacitors in parallel across the output. Analog Voltage Adjust................................................ 0 to +5V 3. <4% deviation recovering to within 1% for 25% load change. Input Immunity, Conducted 4. Typical efŢ ciency is at low end of range for 12V output and at high end of range for 24V output. Fast Transients, Line-Line ................±500V (EN61000-4-4) 5. Input-output isolation Ţ gure is for isolation components only. Surges, Line-Line .............................±500V (EN61000-4-5) 100% production Hipot tested input to ground. Surges, Input Ground .......................±500V (EN61000-4-5) Input Protection ......................................... Internal Fuse, 30A CONNECTOR: POSITRONICS PCIM37W16RM400A1 MATE: PCIM37W16RF400A1 CASE OUTLINE PIN CONNECTIONS PIN FUNCTION PIN FUNCTION 1 +V Out 14 Output Power Good/ADD GA1 2 +V Out 15 Input Power Fail 3 +V Out 16 V Trim 4 V Return 17 Overtemp. Warning/ADD GA0 5 V Return 18 Current Share 6 V Return 19 Current Monitor/ADD GA2 7 Enable 20 + 5V Standby 8 +Sense 21 Standby Return 9 - Sense 22 Chassis Ground 10 Inhibit 23 Chassis Ground 11 Spare/SDA 24 - DC Input 12 Spare/SCL 25 - DC Input 13 - Sense 26 + DC Input *NOTES: For unit to operate, pin 7 must be at logic LO or shorted to pin 9. For proper operation the following pins must be connected together: All V Out pins (1-3); MATING INTERFACE BOARD all V Return pins (4-6). Pins 11, 12, 14, 17 & 19 carry 2 2 I C functions when the I C option is Ţ tted. Order Kit Number 009-0280-0009 ALL DIMENSIONS IN INCHES (mm). All speciŢ cations subject to change without notice. UNIPOWER CORPORATION • 3900 Coral Ridge Drive, Coral Springs, Florida 33065, UNITED STATES • Tel: 954-346-2442 • Fax: 954-340-7901 • sales@unipower-corp.com UNIPOWER EUROPE • Parkland Business Centre, Chartwell Road, Lancing, BN15 8UE, ENGLAND • Tel: +44(0)1903 768200 • Fax: +44(0)1903 764540 • info@unipower-europe.com Call U.S.: (954) 346-2442 • sales@unipower-corp.com Call U.K.: +44(0) 1903 768200 • info@unipower-europe.com CORPORA TION SPECIFICATIONS, TPCMQR1U3-48 RACKS/SHELVES 17.19 (437) FRONT 1.72 (43.7) VIEW 1 2 3 No. 8-32 Studs GND (2 per Module) BACK GND VIEW +V -V J4 3 2 1 DC OUT DC IN J4 SIGNAL CONNECTOR Standard 25-Pin Subminiature D Connector J4 PIN CONNECTIONS MAXIMUM RATED OUTPUT FOR 3 MODULES PIN FUNCTION PIN FUNCTION MODULES NON-REDUNDANT 2+1 REDUNDANT 1 Inhibit 14 Input Power Fail - 1 TPCMQ48-12/24 12VDC @ 150.0A 12VDC @ 108.4A TPCMQ48-13/48 13.6VDC @ 143.4A 13.6VDC @ 143.4A 2 Overtemp. Warning - 1 15 Output Power Good - 1 24VDC @ 087.6A 24VDC @ 058.4A TPCMQ48-24/29 3 Current Monitor - 1 16 Input Power Fail - 2 27.2VDC @ 077.1A 27.2VDC @ 051.4A TPCMQ48-27/26 4 Overtemp. Warning -2 17 Output Power Good - 2 5 Current Monitor - 2 18 Input Power Fail - 3 6 Overtemp. Warning - 3 19 Output Power Good - 3 7 Current Monitor - 3 20 Module Present -1 8 +5V Standby 21 Module Present - 2 9 SDA 22 Module Present - 3 10 Current Share 23 - Sense 11 +Sense 24 Remote Adjust -1 12 Remote Adjust - 2 25 Remote Adjust - 3 13 SCL NOTE: Standby return is connected to -Sense lead. Current rating of +5Vstandby is 250mA. All signals are referenced to -Sense lead. Pins 9 and 13 are 2 I C outputs when that option is present. NOTES: RACK ADAPTOR MODULES & ACCESSORIES: Order by Part No. 1. All connections are made to the rear of the rack/shelf. The Type Function PART NO. modules are 1, 2, 3, from left to right as seen from the front Converts TTL level DC Good signal to 009-1005-0000 of the rack/shelf. Relay Adaptor Form-C dry contact. 2. All module outputs are connected in parallel in the rack/shelf (See separate datasheet for details.) with active current sharing between them. Sends SNMP Alarm Traps over an 009-1006-0000 TCP/IP Ethernet network on change 3. There is a separate DC input for each module, but the inputs SNMP Adaptor of state of the DC Good signals. may be paralleled by means of two shorting bars. Order kit no. 775-1461-0000 for the two bars. (See separate datasheet for details.) Required when using with DSC1000 009-1001-0000 4. The Module Present outputs (J4 pins 20, 21 & 22) are I²C Adaptor Controller. Specify -Z option. grounded (to -Sense) when the module is plugged in and (See DSC1000 Manual for full details.) open when the module is out. Used to blank off unused module slots. 775-1450-0010 2 Blanking Kit 5. For details on the I C function (option Z), contact the factory. One Ţ tted as standard. www.unipowercorp.com or www.powercassette.com tpcmq48 ds revi-04-04-11 Copyright © 2008-2011 Unipower Corporation. All rights reserved. - +