CORPORA TION ® PowerCassette : NEXT GENERATION FRONT-END SWITCHER 1U High, Up to 800 Watts with PFC and Integral Hot Swap Provision FEATURES Includes Isolated 5V, ¼ A Standby Output Hot-Swap or Chassis Mount Versions 12, 24 or 48 VDC Outputs Integral LED Status Indicators 2 PCM Series I C Serial Data Bus Option (Chassis Mount) Up to 10 Watts/Cubic Inch Power Density Power Factor Corrected Low Profi le: 1.6 Inches High Single Hot-Swappable Connector 1U High AC Front Entry Version 1.6” x 5” x 10” TPCM Series Reverse Air Flow Option (Hot-Swap) (41 x 127 x 254 mm) Staged Pin Engagement ORing Diode on Output 1U, 19” Racks Hold 2 or 3 Units* Active Current Sharing Universal 85 to 264VAC Input Class B EMI Input Filter Optimized Thermal Management Three-Unit Rack No Minimum Load Control & Monitoring Features TWO-YEAR WARRANTY *TPCM Models Patents Issued & Pending LVD73/23/EEC STANDARD & OPTIONAL MODELS Delete “T” prefi x to model no. for chassis mount version. MAX. OUTPUT OUTPUT INPUT MODEL CONFIGURATION OUTPUT PFC VOLTAGE CURRENT VOLTAGE NUMBER POWER 650W 12VDC 54.2A 85-264VAC YES TPCM3000 700W 24VDC 29.2A 85-264VAC YES TPCM5000 Standard Rear Input/Output 800W 48VDC 16.7A 85-264VAC YES TPCM7000 480W 12VDC 40.0A 85-264VAC YES TPCM3000E 525W 24VDC 21.9A 85-264VAC YES TPCM5000E 600W 48VDC 12.5A 85-264VAC YES TPCM7000E Optional Front IEC Input NOTE: The table does not show the independent 5V, ¼A standby output which is standard on all models. OPTIONS SAFETY STANDARDS OUTPUT CODE OPTION • UL60950 DERATING • CSA22.2, No. 60950 • EN60950 R Reverse Air Flow (Back to 20% Front) on Standard Models R Reverse Air Flow on “E” 16.6% Suffi x Models RACK MOUNT ORDERING GUIDE: For 1U, 19-inch rack holding three TPCM models, 2 Z I C Serial Data Bus N/A order TPCMR1U3. NOTE: Add Option Code as suffi x to model no. See picture of Option E on See separate data sheet for racks. next page. Contact factory on availability of Option Z. www.unipowercorp.com or www.powercassette.com Copyright © 2002-2010 Unipower Corporation. All rights reserved. � CORPORA TION ® SPECIFICATIONS, PowerCassette PCM & TPCM SERIES FRONT ENDS o Typical at Nominal 115/230VAC Line, Full Load and 25 C Unless Otherwise Noted. OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS 4 Total Output Power, Continuous, Max ............. 480-800 Watts Effi ciency ) ........................................... 80-87% at Full Load Voltage Adjustment Range, Min. ......................................±5% Switching Frequency, PFC Converter ..................48-110kHz 1 Total Regulation , ........................................................... 2.0% Output Converter ....... 275kHz Nominal 5 Total Regulation, Standby Supply ................................. 5.0% Isolation, Class I, min. 2 Ripple & Noise, Pk-Pk ) .................................................... 1% Input-Output ......................................................3000VAC Holdup Time .................................................................. 20mS Input-Ground .....................................................1500VAC 3 Dynamic Response ) .................................................. 300μS Output-Ground ..................................................... 50VDC Temperature Coeffi cient ..................................... ±0.02%/°C MTBF (Bellcore) ............................................. 200,000 Hours Minimum Load .................................................................... 0A Safety Standards ......... EN60950, UL1950, CSA22.2 No.950 Overload Protection ......................................... Auto Recovery ENVIRONMENTAL SPECIFICATIONS Overvoltage Protection ..............................Latched Shutdown o Operating Temperature ..........................0°C to 70 C Ambient Remote Sense .......................................Up to 0.25V Per Wire o o o Derating ............................................ 2.5% / C, 50 C to 70 C Current Share ..................................... ±10% Full Load Rating o o Storage Temperature ......................................-40 C to +85 C Standby Output ................................................... +5V, 250mA Cooling ......................................... Integral Ball Bearing Fans DC Power Good Signal .......................................... Logic Low AC Power Fail Signal .............................................Logic High PHYSICAL SPECIFICATIONS Global Inhibit .......................................................... Logic Low Case Material .........................................................Aluminum Enable .................................................................... Logic Low Dimensions, Inches(mm) ................... 1.6 H x 5.0 W x 10.0 D Thermal Warning ....................................................Logic High (40.6 x 127 x 254) Weight ..........................................................2.9 lbs. (1.3 kg.) INPUT SPECIFICATIONS Input Voltage Range ............................................. 85-264VAC NOTES: 1. No load to full load, including line regulation and load regulation. Power Factor ....................................................................0.99 2. 20MHz bandwidth. Measure with 0.1μF ceramic and Input Frequency ........................................................ 47-63Hz 10μF tantalum capacitors in parallel across the output. 3. <4% deviation recovering to within 1% for 25% load change. Inrush Current Limiting ............................................ 30A Peak 4. Typical effi ciency is at low end of range for 12V output and at Input EMI Filter .........................................EN55022 Curve B high end of range for 48V output. 5. Input-output isolation fi gure is for isolation components only. FCC20780 pt. 15J Curve B 100% production Hipot tested. Harmonic Distortion ........................................... EN61000-3-2 MATING INTERFACE BOARD Input Immunity, Conducted Fast Transients, Line-Line ..... ±2kV (EN61000-4-4 Level 3) Order Kit Number Surges, Line-Line .................. ±2kV (EN61000-4-5 Level 3) 009-3850-0000 Surges, Line-Ground ............. ±4kV (EN61000-4-5 Level 4) Input Protection ......................................... Internal Fuse, 20A PIN CONNECTIONS PIN FUNCTION PIN FUNCTION CONNECTOR: POSITRONICS PCIB24W9M400A1 1 +V Out* 13 Module Present MATE: PCIB24W9F400A1 2 +V Out* 14 DC Power Good/ADD GA1* 3 +V Out* 15 AC Power Fail 4 V Return* 16 V Trim 5 V Return* 17 Overtemp. Warning/ADD GA0* CASE OUTLINE 6 V Return* 18 Current Share 7 Enable* 19 Current Monitor/ADD GA2* 8 + Sense 20 +5V Standby 9 - Sense 21 Standby Return 10 Inhibit 22 Chassis Ground 11 Spare/SDA* 23 AC Line 12 Spare/SCL* 24 AC Neutral *NOTES: For unit to operate, pin 7 must be at logic LO or shorted to pin 9. For proper operation the following pins must be connected together: All V Out pins (1-3); all V Return pins (4-6). Pins 11, 12, 2 14, 17 & 19 function as I C outputs when that option is present. For I²C operation pin 21 must be connected to pin 9. IEC Input Version (Option E) DC POWER AC POWER GOOD LED GOOD LED NOTE: The TPCM Model is shown. The PCM version ALL DIMENSIONS IN INCHES (mm). does not have handle or mounting bracket with bolt. All specifi cations subject to change without notice. pcm-tpcm-revX-040610.indd �