Elite.Parts

Image of TRANSITION NETWORKS CRMFE1015-200

Description

Transition Networks CRMFE1015-200 Ethernet Switch - 100BASE-TX (RJ-45) [100 m/328 ft.], 100BASE-FX 1310nm single mode (SC) [40 km/24.9 mi.]

Part Number

CRMFE1015-200

Price

Request Quote

Manufacturer

TRANSITION NETWORKS

Lead Time

Request Quote

Category

MEDIA CONVERTERS / EXTENDERS / CROSS-CONNECTS

Specifications

3-position Jumpers

Jumper (J2): Enable/Disable AutoCross, Jumper (J6):Hardware: mode is determined by 4-position switch settings, Software: mode is determined by most recently saved on-board microprocessor settings.

4 position Switch

Pos 1: Auto-Neg: (ON) Advertises 100Mb/s full/half-duplex during auto-negotiation; (OFF), (Used primarily when connecting to hub) Operates at 100Mb/s in duplex mode of attached device. Pos 2: PAUSE: Applies only if Switch 1 is UP AND device is connected to Auto-Negotiating device(s) capable of Pause Control Frame propagation. (UP) ALLOWS negotiation of Pause Control Frame. (DOWN) Does NOT allow negotiation of Pause

Dimensions

Width: 0.86" [22 mm], Depth: 5.0" [127 mm], Height: 3.4" [86 mm]

Environment

See chassis specifications

Power Consumption

3.4 watts

Regulatory Compliance

CISPR/EN55022 Class A & B + EN55024; FCC Class A & B; CE Mark

Shipping Weight

1 lb. [0.45 kg]

Standards

IEEE Std. 802.3

Status LEDs

Power LKF (Fiber Link)\RXF (Fiber Receive), RXC (Copper Receive), LKC (Copper Link)

Warranty

Lifetime

Features

AutoCross
Automatic Link Restoration
Bandwidth Allocation
Can be used with any Point System Chassis
Far-End-Fault (FEF)
Jumbo Frame Support
Link Pass Through
Loopback
Pause
Remote Firmware Upgrade
Remote Management
Auto-Negotiation

Datasheet

Transition Networks=CRMFE1011-200=datasheet1-1789000716.pdf

657 KiB

Download

Extracted Text

point system™ slide-in-module network interface device Fast Ethernet 100BASE-TX to 100BASE-FX AUTO BANDWIDTH REMOTE FIRMWARE AUTO NEG AUTO CROSS LINK PASS THRU FAR END FAULT LINK RESTORE PAUSE REMOTE MGMT LOOP BACK ALLOCATION UPGRADE with Remote Management & Bandwith Allocation CRFME10xx-20x Remotely Managed Fast Ethernet NID Ordering Info CRMFE1011-200 (Network Interface Device) 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1300nm MM (ST) [2 km/1.2 mi.] Link Budget: 11.0 dB CRMFE1013-200 With the Remotely Managed Fast Ethernet NID, 100BASE-TX (RJ-45) [100 m/328 ft.] service providers can now monitor and manage to 100BASE-FX 1300nm MM (SC) � In-band management of stand the entire optical link from the Central Office (CO) [2 km/1.2 mi.] Link Budget: 11.0 dB alone Fast Ethernet NID to the Customer Premise Equipment (CPE). They CRMFE1014-200 also have the ability to remotely change the �Remote Loopback assists in 100BASE-TX (RJ-45) [100 m/328 ft.] bandwidth offered to the customer in increments to 100BASE-FX 1310nm SM (SC) diagnosing network problems of 64KBps and choose the appropriate mode of [20 km/12.4 mi.] Link Budget: 16.0 dB �Upstream and downstream connection straight from their Network CRMFE1015-200 Bandwidth Control allows Management Centers. 100BASE-TX (RJ-45) [100 m/328 ft.] service providers to offer an to 100BASE-FX 1310nm SM (SC) Devices should be used in pairs. Typical instal- [40 km/24.9 mi.] Link Budget: 26.0 dB array of services lation will include a chassis card installed in the CRMFE1016-200 Point System™ locally and a stand-alone device 100BASE-TX (RJ-45) [100 m/328 ft.] (SRMFE pg. 81) installed at the remote location. to 100BASE-FX 1310nm SM (SC) [60 km/37.3 mi.] Link Budget: 29.0 dB Features CRMFE1017-200 � Auto-Negotiation 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1550nm SM (SC) � AutoCross™ [80 km/49.7 mi.] Link Budget: 29.0 dB � Link Pass Through Specifications CRMFE1035-200 � Far-End-Fault (FEF) 100BASE-TX (RJ-45) [100 m/328 ft.] Standards IEEE Std. 802.3 to 100BASE-FX 1550nm SM (SC) � Automatic Link Restoration [120 km/74.6 mi.] Link Budget: 36.0 dB 3-position Jumpers Jumper (J2): Enable/Disable AutoCross™ � Pause Single Fiber Products � Remote Management Jumper (J6): Recommended use in pairs Hardware: mode is determined by 4-position � Loopback CRMFE1029-200 switch settings 100BASE-TX (RJ-45) [100 m/328 ft.] � Bandwidth Allocation Software: mode is determined by most recently to 100BASE-FX 1310nm TX / 1550nm RX sin- saved on-board microprocessor settings. � Jumbo Frame Support gle fiber SM (SC) � Remote Firmware Upgrade 4 position Switch Pos 1: Auto-Neg: (ON) Advertises 100Mb/s [20 km/12.4 mi.] Link Budget: 19.0 dB full/half-duplex during auto-negotiation; (OFF) �Can be used with any Point System™ Chassis CRMFE1029-201 (Used primarily when connecting to hub) Operates 100BASE-TX (RJ-45) [100 m/328 ft.] at 100Mb/s in duplex mode of attached device. to 100BASE-FX 1550nm TX / 1310nm RX sin- Pos 2: PAUSE: Applies only if Switch 1 is UP AND gle fiber SM (SC) device is connected to Auto-Negotiating device(s) Remotely Managed Fast Ethernet [20 km/12.4 mi.] Link Budget: 19.0 dB capable of Pause Control Frame propagation. (UP) ALLOWS negotiation of Pause Control Frame. CRMFE1029-202 (DOWN) Does NOT allow negotiation of Pause 100BASE-TX (RJ-45) [100 m/328 ft.] Control Frame. to 100BASE-FX 1310nm TX / 1550nm RX sin- Pos 3: Link Pass Through: (UP) enabled; gle fiber SM (SC) (DOWN) disabled [40 km/24.9 mi.] Link Budget: 25.0 dB Pos 4: Far-End-Fault: (UP) enabled; CRMFE1029-203 (DOWN) disabled 100BASE-TX (RJ-45) [100 m/328 ft.] Status LEDs Power to 100BASE-FX 1550nm TX / 1310nm RX sin- LKF (Fiber Link)\ gle fiber SM (SC) RXF (Fiber Receive) [40 km/24.9 mi.] Link Budget: 25.0 dB RXC (Copper Receive) LKC (Copper Link) Dimensions Width: 0.86" [22 mm] Depth: 5.0" [127 mm] Height: 3.4" [86 mm] Power Consumption 3.4 watts Environment See chassis specifications Shipping Weight 1 lb. [0.45 kg] Regulatory Compliance CISPR/EN55022 Class A & B + EN55024; FCC Class A & B; CE Mark Warranty Lifetime ©2009 Transition Networks, Inc. Transition Networks, Inc. tel: 952.941.7600 / 800.526.9267 All trade marks are the property of their respective owners. Worldwide Headquarters: fax: 952.941.2322 Technical information is subject to change without notice. 10900 Red Circle Drive info@transition.com Minnetonka, MN 55343 USA http://www.transition.com

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products