100BASE-TX to 100BASE-FX [Class A] see also: Fast Ethernet Stand-Alone Media Converters point system™ slide-in-module media converter Fast Ethernet CFETF10xx-110 Fast Ethernet Class A Media Converter Ordering Info [Class A] CFETF1011-110 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1300nm MM (ST) [2 km/1.2 mi.] Link Budget: 11.0 dB CFETF1013-110 4 Integrate fiber into a 100BASE -TX copper environment 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1300nm MM (SC) 4 Provides a fiber interface when connected to devices [2 km/1.2 mi.] Link Budget: 11.0 dB with RJ-45 ports CFETF1014-110 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1310nm SM (SC) Features [20 km/12.4 mi.] Link Budget: 16.0 dB 4 Round trip delay of only 40 bit times, far below the Class II CFETF1015-110 rating of 92 bit times 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-FX 1310nm SM (SC) 4 Auto-Negotiation [40 km/24.9 mi.] Link Budget: 29.0 dB 4 AutoCross™ [ CFETF1016-110 100BASE-TX (RJ-45) [100 m/328 ft.] 4 Link Pass Through to 100BASE-FX 1310nm SM (SC) 4Automatic Link Restoration [60 km/37.3 mi.] Link Budget: 29.0 dB 4Field Upgradeable Firmware CFETF1017-110 100BASE-TX (RJ-45) [100 m/328 ft.] 4 Can be used with any Point System™ Chassis to 100BASE-FX 1550nm SM (SC) [80 km/49.7 mi.] Link Budget: 29.0 dB CFETF1040-110 100BASE-TX (RJ-45) [100 m/328 ft.] to 100BASE-X SFP slot (empty) Specifications Extend Network Distance Deploy fiber in a strategic and economical Optional Accessories (sold separately) manner by using Fast Ethernet converters, SFP Modules Standards IEEE Std. 802.3 which can extend to distances that copper 3-position Jumper Hardware: Converter mode is determined by cannot reach. 4-position switch settings Software: Converter mode is determined by most recently saved on-board microprocessor settings 4-position Switch 1. Auto-Negotiation (UP = enabled): Allows FCC & CISPR Class A devices comply detection of, and adaptation to, full-duplex or half- with radiated emissions standards for duplex mode in device attached to copper link commercial applications in the United 2. Link Pass Through (UP = enabled): Allows a fault EITHER on the copper OR on the fiber side of the media States (FCC Class A) and Europe converter to stop signal and data transmission on the (CISPR Class A). other side 3. AutoCross™ (UP = enabled): Allows straight-through FCC & CISPR Class B devices comply twisted pair cable to be used for crossover connections with radiated emissions standards for 4. Not Used residential applications in the United Status LEDs Power: Indicates that DC power is connected States (FCC Class B) and Europe TX (Link Copper): ON indicates TP link; Blinking indicates TP receive; (CISPR Class B). FX (Link Fiber): ON indicates fiber link; Blinking indicates Fiber receive [See CFETF10xx-205 for Class B product.] Dimensions Width: 0.86” [22 mm] Depth: 5.0” [127 mm] Height: 3.4” [86 mm] Power Consumption 2.5 Watts Environment See chassis specifications Shipping Weight 1 lb. [0.45 kg] Regulatory Compliance CE Mark, FCC Class A; CISPR Class A; VCCI Class 1 Warranty Lifetime 100BASE-TX to 100BASE-FX [Class A] Point System™