TRACO POWER TSM 1215D

DC/DC Converter TSM Series 1 Watt Features SMD Package (SOIC-14/18) Construction in Lead Frame Technology Isolated Single and Dual Output I/O-Isolation 1‘000 VDC High Efficiency Operating Temperature –40°C to +85°C Reflow Solder Temperature up to 230°C High Accuracy of Pin Co-Planarity Available in Tape and Reel Package 3 Year Product Warranty The TSM series are isolated DC/DC converters with 1W output power implemented in a molded plastic package with a pin accuracy suit- able for high volume SMD-production. The devices do not require a special reflow process but can be soldered like standard SMD-com- ponents. With their small footprint these converters are the economi- cal solution for point of use power conversion, ground loop elimina- tion, noise reduction and digital interface applications. Models Ordercode Input voltage Output voltage Output current max. Efficiency typ. TSM 0505S 5 VDC 200 mA 80 % TSM 0509S 9 VDC 110 mA 78 % TSM 0512S 12 VDC 80 mA 80 % TSM 0515S 5 VDC ±10% 15 VDC 65 mA 81 % TSM 0505D ± 5 VDC ±100 mA 75 % TSM 0512D ±12 VDC ± 40 mA 79 % TSM 0515D ±15 VDC ± 30 mA 79 % TSM 1205S 5 VDC 200 mA 81 % TSM 1209S 9 VDC 110 mA 78 % TSM 1212S 12 VDC 80 mA 81 % TSM 1215S 12 VDC ±10% 15 VDC 65 mA 82 % TSM 1205D ± 5 VDC ±100 mA 75 % TSM 1212D ±12 VDC ± 40 mA 80 % TSM 1215D ±15 VDC ± 30 mA 80 % www.tracopower.com Page 1 DC/DC Converter TSM Series 1 Watt Input Specifications Input current no load /full load 5 Vin models 30 mA / 260 mA typ. 12 Vin models 15 mA / 110 mA typ. Surge voltage (1 sec. max.) 5 Vin models 9 V max. 12 Vin models 18 V max. Reverse voltage protection 0.3 A max. Reflected input ripple current can be reduced by ext. 1–2.2 µF polyester film capacitor Input filter internal capacitors Output Specifications Voltage set accuracy ± 3 % Voltage balance (dual output models) ± 1 % max. Regulation – Input variation ± 1.2 % / 1 % change Vin – Load variation 20 – 100 % ± 10 % max. Ripple and noise (20 MHz Bandwidth) 120 mVpk-pk max. Temperature coefficient ± 0.02 % / °C Short circuit protection limited 1 sec. max. Capacitive load – Single output models 22 µF max. – Dual output models 10 µF max. General Specifications Temperature ranges – Operating (see also enclosed derating curve) – 40 °C ... +85 °C (no derating) – Storage – 55 °C ... +125 °C Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217E) >2’000’000 h @ 25 °C Isolation voltage Input/Output 1‘000 VDC Isolation capacity Input/Output 40 pF typ. Isolation resistance Input/Output >1‘000 Mohm Switching frequency 100 kHz typ. (Frequency modulation) Frequency change over line and load ± 30 % Physical Specifications Case material Epoxy molding compound (flammability to UL 94-V0) Package weight – Single output models 1.2 g (0.04 oz) – Dual output models 1.5 g (0.05 oz) Reflow soldering profile Peak temp. 230°C (10 sec max.) 185°C for 90 sec max. Convection reflow solder process is recommended All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. www.tracopower.com Page 2 DC/DC Converter TSM Series 1 Watt Derating all TSM Models +85˚C +105˚C 100 100 90 90 80 80 70 70 60 60 50 50 -5.0% /˚C 40 40 30 30 20 20 10 10 0 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 Ambient Temperature [˚C] Outline Dimensions mm (inches) TSM Single Output Models 6.5 (0.256) S Seating Plane 8 Pins 0.2 M S 8 Pins ± 4˚ P 0.1 S 7.62 (0.3) 7.0 (0.276) 9.2 (0.362) 11.1 (0.437) 0.6 ±0.025 2.54 (0.1) (0.024 ±0.001) NA NA NA +Vo 14 8 14 8 1 7 1 7 –Vin +Vin NA –Vo 2.5 (0.1) NA = not available for electrical connection 12.7 (0.5) Tolerances: ± 0.25 mm (± 0.01) Specifications can be changed without notice All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. www.tracopower.com Page 3 4.7 2.0 (0.079) (0.185) Output Power [%] +0 6.7 0.25 –0.15 8.0 (0.315) +0 (0.01) 0.264 () –0.256 0.25 ± 0.05 (0.01±0.002) Output Power [%] DC/DC Converter TSM Series 1 Watt Outline Dimensions mm (inches) TSM Dual Output Models 6.5 (0.256) S Seating Plane 8 Pins 0.2 M S 8 Pins ± 4˚ P 0.1 S 10.16 (0.4) 7.0 (0.276) 9.2 (0.362) 11.1 (0.437) 0.6 ±0.025 2.54 (0.1) (0.024 ±0.001) NA NA NA +Vo NA 18 10 18 10 1 9 1 9 –Vin +Vin NA Com –Vo 2.5 (0.1) 15.24 (0.6) NA = not available for electrical connection Tolerances: ± 0.25 mm (± 0.01) Specifications can be changed without notice All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. www.tracopower.com Page 4 4.7 2.0 (0.079) (0.185) +0 6.7 8.0 (0.315) 0.25 –0.15 +0 (0.01) 0.264 () –0.256 0.25 ± 0.05 (0.01±0.002) DC/DC Converter TSM Series 1 Watt Solder Pad Dimensions mm (inches) 7.62 (0.3) TSM Single Output Models 2.54 2.54 2.54 (0.1) (0.1) (0.1) 1.0 Min. (0.039 Min.) 10.16 (0.4) TSM Dual Output Models 2.54 2.54 2.54 2.54 (0.1) (0.1) (0.1) (0.1) 1.0 Min. (0.039 Min.) Specifications can be changed without notice Rev. 01/04 Jenatschstrasse 1  CH-8002 Zurich  Switzerland Tel. +41-1284 2911  Fax +41-1201 1168  e-mail: sales traco.ch  internet: http://www.tracopower.com Page 5 @ 10.8 (0.425) 10.8 (0.425) 1.7 1.7 (0.067) (0.067)