DC/DC Converters TES 2N Series, 2 Watt Features UL 60950-1 ◆ Low profile SMD-package ◆ Wide 2:1 input voltage range ◆ I/O isolation 1500 VDC ◆ Input filter meets EN55022, class A ◆ Operating temperature range –40°C to +85°C ◆ Short-circuit protection The TES-2N series is a family of high performance 2W DC/DC converter modules ◆ Qualified for leadfree reflow solder featuring wide 2:1 input voltage ranges. The 28 models come in a low profile SMD process according IPC J-STD-020C 2 package which requires just 3 cm space on the PCB. A high efficiency allows an ◆ Available in tape and reel package operating temperature range of –40°C to 85°C. A built-in EMI input filter complies ◆ 3-year product warranty with EN 55022, class A. Typical applications for these converters are battery ope- rated equipment, instrumentation, communication and industrial electronics, every- where where isolated, tightly regulated voltages are required. Models Ordercode Input voltage range Output voltage Output current max. Efficiency typ. TES 2N-0510 3.3 VDC 500 mA 70 % TES 2N-0511 5 VDC 400 mA 73 % TES 2N-0512 12VDC 165 mA 75 % 4.5 – 9.0 VDC TES 2N-0513 15 VDC 135 mA 73 % (nominal 5 VDC) TES 2N-0521 ± 5 VDC ±200 mA 64 % TES 2N-0522 ±12 VDC ±85 mA 69 % TES 2N-0523 ±15 VDC ±65 mA 71 % TES 2N-1210 3.3 VDC 500 mA 73 % TES 2N-1211 5 VDC 400 mA 77 % TES 2N-1212 12 VDC 165 mA 80 % 9 – 18 VDC TES 2N-1213 15 VDC 135 mA 80 % (nominal 12 VDC) TES 2N-1221 ±5 VDC ±200 mA 73 % ±12 VDC ±85 mA 78 % TES 2N-1222 TES 2N-1223 ±15 VDC ±65 mA 78 % TES 2N-2410 3.3 VDC 500 mA 72 % TES 2N-2411 5 VDC 400 mA 77 % TES 2N-2412 12 VDC 165 mA 80 % 18 – 36 VDC TES 2N-2413 15 VDC 135 mA 81 % (nominal 24 VDC) TES 2N-2421 ±5 VDC ±200 mA 74 % TES 2N-2422 ±12 VDC ±85 mA 78 % TES 2N-2423 ±5 VDC ±65 mA 80 % TES 2N-4810 3.3 VDC 500 mA 71 % TES 2N-4811 5 VDC 400 mA 73 % TES 2N-4812 12 VDC 165 mA 79 % 36 – 75 VDC TES 2N-4813 15 VDC 135 mA 79 % (nominal 48 VDC) TES 2N-4821 ± 5 VDC ±200 mA 71 % TES 2N-4822 ±12 VDC ±85 mA 77 % TES 2N-4823 ±15 VDC ±65 mA 77 % http://www.tracopower.com Page 1 of 3 DC/DC Converters TES 2N Series 2 Watt Input Specifications Input current at full load (nominal input) 5 Vin models: 600 mA typ. 12 Vin models: 220 mA typ. 24 Vin models: 110 mA typ. 48 Vin models: 55 mA typ. Surge voltage (100 msec. max.) 5 Vin models: 11 V max. 12 Vin models: 25 V max. 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise (input) EN 55022 level A, FCC part 15, level A Output Specifications Voltage set accuracy ±2 % Regulation – Input variation Vin min. to Vin max. 0.5 % max. – Load variation 25 – 100 % 0.75 % max. dual output models: 2.0 % (balanced load) Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max Temperature coefficient ±0.02 %/K Short circuit protection indefinite, automatic recovery Minimum load 25 % of rated max current (operation at lower load condition is safe but a higher output ripple will be experienced) Capacitive load 3.3 VDC output models: 2’200 µF max. 5 VDC output models: 1’000 µF max. 12 VDC output models: 170 µF max. 15 VDC output models: 110 µF max. ±5 VDC output models: 470 µF max. ±12 VDC output models: 100 µF max. ±15 VDC output models: 47 µF max. General Specifications Temperature ranges – Operating –40°C to +85°C – Storage –55°C to +125°C Derating 3.5 %/K above +71°C Humidity (non condensing) 95 % rel. H max. Reliability, calculated MTTF (MIL-HDBK-217F, @ +25°C, ground benign) >1.0 Mio h Isolation voltage (60sec) – Input/Output 1’500 VDC Isolation capacity – Input/Output 250 pF Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm Switching frequency 300 kHz (PFM) Safety standards UL 60950-1, IEC/EN 60950-1 Safety approvals CSA File No. 226037 http://directories.csa-international.org All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TES 2N Series 2 Watt Physical Specifications Casing material DAP (UL94V-0 rated) Weight 3.8 g (0.13oz) Lead-free reflow solder process as per J-STD-020D.01 (to find at: www.jedec.org - free registration required) Moisture sensivity level (MSL) level 2 as per J-STD-033B.01 (to find at: www.jedec.org - free registration required) Washing process www.tracopower.com/products/smd- wash.pdf Packaging www.tracopower.com/products/tes2n-pack.pdf Outline Dimensions 24.0 (0.94) 0 - 4° 0.15 1.0 (0.04) 16 10 9 Pin-Out top view Pin Single Dual 1 –Vin (GND) –Vin (GND) 1 7 8 7 No con. No con. 8 No con. Common 9 +Vout +Vout 3.11 (0.12) 15.24 (0.60) 2.54 (0.10) 10 –Vout –Vout +Vin +Vin 16 1.4 (0.055) min. Solder Pad Dimension Dimensions in [mm], () = Inch Tolerances ±0.25 (±0.01) 3.11 (0.12) 15.24 (0.60) 2.54 (0.10) Pin pitch tolerances ±0.05 (±0.002) Specifications can be changed any time without notice Rev. 02/10 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com Page 3 of 3 13.7 (0.54) 0.25 (0.01) 18.1 (0.71) 8.0 (0.31) 2.8 13.7 (0.54) 2.8 (0.11) (0.11)