RV16 - TOCOS - Elite.Parts

Description

TOCOS RV16 16mm Diameter, Single-Turn, Carbon Industrial Panel Controls

Part Number

RV16

Price

Request Quote

Manufacturer

TOCOS

Lead Time

Request Quote

Category

PRODUCTS - R

Datasheet

TOCO-RV16-Series-Industrial-Panel-Controls-datasheet1-1269451750.pdf

645 KiB

Download

Extracted Text

® TOCOS RV16 Series PANEL CONTROLS 16mm Diameter, Single-Turn, Carbon Industrial Panel Controls RV16YPL RV16YN RV16YNME Features 16mm diameter, single-turn industrial panel controls Carbon film element Linear or audio tapers � � � Single and tandem units, single shaft; dual unit, dual shaft Optional switch, center detent, and shaft lock available � � 3.2mm diameter metal shafts in slot, flat or round end styles Standard 10mm or 15mm shaft length � � Panel or PC board mounting styles Lug or pin terminals Right angle mount pin configurations � � � Specifications Electrical Environmental Standard Resistance Range . . . . . . . . . . B = 100Ω to 2MΩ Temperature Range . . . . . . . . . . . . . . . . . . �10�Cto�85�C A,C = 2kΩ to 2MΩ Low Temperature Exposure . . .�10�C, 1 hour without load ) � � Resistance Tolerance . . . . . . . . . . . . . . . . . 10% standard ∆T/R 2.5% � End Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Ω max. Load Life . . . . . . . . . . 40�C, 90 minutes on, 30 minutes off, 1,000 hours with rated load Resistance Taper . . . . B = linear; A = CW audio (logarithm); ) � ∆T/R 15% C = CCW audio (logarithm) � Moisture Resistance . . . . . . . . . . . . . . . 40�C, 90-95%RH, Peak Noise (C.R.V.) . . . . . . . 3% or 3Ω, whichever is greater 96 hours without load Power Rating . . . . . . . . . . . . . B = 0.1 watt; A,C = 0.05 watt ) � ∆T/R 10% � � at 40�C, 0 watt at 85�C � Thermal Shock . . . . . . . . . . . . . . . . . . . . . . .�10�C~ 85�C, Maximum Input Voltage . . . . . . . . 200VDC or power rating, 5 cycles without load whichever is smaller ) � ∆T/R 10% Insulation Resistance . . . . . . .100MΩ minimum at 500VDC Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50G, 11 m/s ) � ∆T/R 2.5% Dielectric Strength . . . . . . . . . . . . . . . . . . 500VAC, 1 minute Vibration . . . . . . . . . . . . . . . . . . .10-55Hz, 1.5mm amplitude, � Adjustment Travel . . . . . . . . . . . . . . . . . . . . . . . . . 240� 10� 3 directions, 2 hours each ) � ∆T/R 2.5% Mechanical Soldering Heat Resistance . . . . . . . . . . . 350�C, 3 seconds; Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . 260��10� 260�C, 5 seconds (PCB units) Shaft Torque ) � ∆T/R 2% •cm (0.283 to 2.828 oz •in) Single Unit . . . . . 20.4 to 204 gf Rotational Life . . . . 15,000 cycles (500 cycles for shaft lock Other Units . . . . 20.4 to 357 gf •cm (0.283 to 4.949 oz •in) models only) without load •cm (42.42 oz •in) max. Stop Strength . . . . . . . . . . . 3.06 kgf ) � ∆T/R 10% •cm (141.4 oz •in) max. Mounting Nut Torque . . . . . 10.2 kgf Standard Rotary Switches Solderability . . . . . . . . . . . . . . . . . . . . . . . 235�C, 5 seconds Switch Rating . . . . . . . . . . . . . 110VAC, 0.5A, SPDT or SPST Marking . . . . . . . . . . . . . Model type, taper, resistance code, Contact Resistance . . . . . . . . . . . . . . . . . . . . . . 0.05Ω max. terminal identification, date code •cm (21.21 oz •in) max. Operating Torque . . . . . . . . 1,530 gf Operating Life . . . . . . . . . . . . . . . 10,000 cycles without load ∆T/R = Total Resistance Change TOCOSAMERICA,INC. 19 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com RV16 Series Dimensions Unit: mm RV16YN & RV16YN-4C (with Center Detent) Panel Mount, Single Unit, Single Shaft Right Angle Ear-Lug Terminals Recommended Panel Mounting Hole RV16YL Panel Mount, Single Unit, Single Shaft with Shaft Lock Right Angle Ear-Lug Terminals Recommended Panel Mounting Hole RV16YNMH & RV16YNSH Panel Mount, Single Unit with Switch, Single Shaft Right Angle Ear-Lug Terminals, Rear Exit Lug Terminals for 0.5A SPDT or SPST Switch Recommended Panel Mounting Hole The SPST switch (SH code designation) does not have a B terminal. * 20 TOCOSAMERICA,INC. 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com RV16 Series Dimensions Unit: mm RV16YP PCB Mount, Single Unit, Single Shaft Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Standoff Rear Support Bracket Recommended PCB Mounting Holes RV16YPL PCB Mount, Single Unit, Single Shaft with Shaft Lock Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Standoff Rear Support Bracket Recommended PCB Mounting Holes RV16YG Panel Mount, Ganged Tandem Unit, Single Shaft Right Angle Ear-Lug Terminals on Each Unit Recommended Panel Mounting Hole TOCOSAMERICA,INC. 21 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com RV16 Series Dimensions Unit: mm RV16YGP PCB Mount, Ganged Tandem Unit, Single Shaft Right Angle Mount Pin Terminals on Each Unit, 3-Pin Inline Pattern, 2-Pin Standoff Rear Support Bracket Recommended PCB Mounting Holes RV16YGMH Panel Mount, Ganged Tandem Unit with Rear Unit Switch, Single Shaft Right Angle Ear-Lug Terminals on Each Unit, Rear Exit Lug Terminals for 0.5A SPDT Switch Recommended Panel Mounting Hole Connect the A and C terminals only for a SPST switch. Do not use the B terminal. * RV16YD Panel Mount, Dual Unit, Dual Concentric Shaft Right Angle Ear-Lug Terminals on Each Unit Recommended Panel Mounting Hole 22 TOCOSAMERICA,INC. 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com RV16 Series Dimensions Unit: mm RV16YDMH & RV16YDSH Panel Mount, Dual Unit with Rear Unit Switch, Dual Concentric Shaft Right Angle Ear-Lug Terminals on Each Unit, Rear Exit Lug Terminals for 0.5A SPDT or SPST Switch Recommended Panel Mounting Hole The SPST switch (SH code designation) does not have a B terminal. * TOCOSAMERICA,INC. 23 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com RV16 Series Part Numbering System RV 16 Y N -4C MH 20 S B 103 K NOTE: FMS = From Mounting Surface � Resistance Tolerance: K = 10% (standard). Resistance Code: Expressed in ohms. A three digit code where the first two digits are significant figures, and the third digit indicates the number of zeros that follow these figures (i.e.,100 = 10Ω;101 =100Ω;102 = 1,000Ω; 103 = 10,000Ω;105 = 1,000,000Ω). See table for standard resistance values. For Single Unit: Specify taper and resistance code as shown. For Ganged Tandem Unit or Dual Unit: Specify a taper code and resistance code for each unit starting with the front unit followed by the rear unit. If both units have the same taper and resistance codes, add “X2” suffix per example below. Examples: B103A503 or if both units are the same: B103X2 Resistance Taper: B = Linear. A = CW Audio (logarithm). C = CCW Audio (logarithm). Shaft End Style: S = Slotted; F = Flatted; R = Round. For Single Shaft: Specify the shaft length (FMS) and shaft end style as shown. For Dual Concentric Shafts: Specify the shaft length (FMS) and shaft end style for the inner shaft followed by the shaft length (FMS) and shaft end style for the outer shaft. Use a dash (-) to separate the code groups for the inner and outer shaft specifications. Example: 30R-20R Standard Shaft Length: 10 = 10mm FMS. 15 = 15mm FMS. Up to 30mm shaft length available (special order). Switch Type: MH = SPDT,110VAC, 0.5A, Rear Exit Lug Terminals. SH = SPST, 110VAC, 0.5A, Rear Exit Lug Terminals. Blank = No Switch. Detent: -4C = Center Detent. Blank = No Detent. Style: N = Panel Mount, Single Unit, Single Shaft, Right Angle Ear-Lug Terminals. L = Panel Mount, Single Unit, Single Shaft with Shaft Lock, Right Angle Ear-Lug Terminals. P = PCB Mount, Single Unit, Single Shaft, Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Standoff Rear Support Bracket. PL = PCB Mount, Single Unit, Single Shaft with Shaft Lock, Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Standoff Rear Support Bracket. G = Panel Mount, Ganged Tandem Unit, Single Shaft, Right Angle Ear-Lug Terminals on Each Unit. GP = PCB Mount, Ganged Tandem Unit, Single Shaft, Right Angle Mount Pin Terminals on Each Unit, 3-Pin Inline Pattern, 2-Pin Rear Standoff Support Bracket. D = Panel Mount, Dual Unit, Dual Concentric Shaft, Right Angle Ear-Lug Terminals on Each Unit. � Operating Temperature Range: Y = �10�C to 85�C. Size: 16 = 16mm Diameter. TOCOS Series Name: RV = Carbon Film Element. Standard Resistance Values and Part Numbering Codes Standard Nominal Total Resistance Values and Part Numbering Codes Resistance (Ω) Code Resistance (Ω) Code Resistance (Ω) Code Resistance (Ω) Code Resistance (Ω) Code 100 101 1,000 102 10,000 103 100,000 104 1,000,000 105 200 201 2,000 202 20,000 203 200,000 204 2,000,000 205 500 501 5,000 502 50,000 503 500,000 504 Refer to Shaft End Styles Specifications and Hardware Specifications for details and availability. For additional information, refer to Guidelines and Precautions for Using Panel Controls. 24 TOCOSAMERICA,INC. 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products