17cm COLOR TFT-LCD MODULE Toshiba Matsushita Display Technology Co., Ltd (6.5 TYPE) LTA065A043F PRODUCT INFORMATION (a-Si TFT) All information is subject to change without notice. Please read bottom notes. FEATURES TENTATIVE (1) “Transmitting type”, High brightness, High contrast, Wide view angle (2) Digital 6 bit RGB input interface (3) LCD drive circuit is built in, but inverter for backlight is not built in (4) Mounting compatible with LTA065A041F RoHS compatible (5) RoHS compliant MECHANICAL SPECIFICATIONS Item Specification *1 Dimensional Outline (Typ.) 151.0 (W) x 115.5 (H) x 10.0 (D) mm Number of Pixels 640 (W) x 480 (H) pixels Active Area 131.52 (W) x 98.64 (H) mm Pixel Pitch 0.2055 (W) x 0.2055 (H) Weight (approximately) 205 g Backlight Sidelight (L-type) *1: The lug (FPC, lump harness and connector) is not included. ABSOLUTE MAXIMUM RATINGS Item Min. Max. Unit (V) -0.3 4.5 V DD Supply voltage (V) --- 3.0 kV(rms) FL FL Driving Frequency (f) --- 100 kHz FL Input Signal Voltage (V) -0.3 V+0.3 V IN DD *2 Operating Temperature -20 65 °C Storage Temperature -30 80 °C Storage humidity --- 95 %(RH) (Max. wet bulb temperature = 39°C) *2:Wet bulb temperature should be 39°C Max.,and no condensation of water. ELECTRICAL SPECIFICATION (Ta=25°C) (RECOMMENDED OPERATION CONDITION) Item Min. Typ. Max. Unit Remarks (V) 3.15 3.30 3.45 V DD Supply Voltage (V) --- 480 --- V(rms) I =7.0mA(rms) FL FL FL Start Voltage (V ) --- SFL 1700 --- V(rms) Ta=-10°C High Level Input voltage (V) 0.7V --- V V IH DD DD Low Level Input voltage (V) 0.0 --- 0.3V V IL DD *4 (I ) --- 240 --- mA(rms) DD Current Consumption *5 (I ) 4.0 7.0 7.5 mA(rms) FL *2*3 Power Consumption --- 4.2 --- W I =7.0mA(rms) FL *3: The surface temperature caused by self heat radiation of cell itself is specified on this item *4: 8 color bars pattern *5: Except the efficiency of FL inverter OPTICAL SPECIFICATION (Ta=25°C) Item Min. Typ. Max. Unit Remarks Contrast Ratio (CR) 100 250 --- --- Viewing Angle (Upper+Lower) --- 90 --- ° (CR≥10) (Left+Right) --- 120 --- ° (T) --- 10 --- ms ON Response Time (T) --- 15 --- ms OFF 300 400 --- cd/㎡ I =7.0mA(rms) FL Luminance (L) 240 340 --- cd/㎡ I =6.0mA(rms) FL 30,000 40,000 --- h I =7.0mA(rms) *6*7 FL Lamp Life Time (MTBF) 50,000 --- --- h I =6.0mA(rms) FL *6: Conditions ;Ta=25°C, I =6.0 or 7.0mA(rms),contimuous lighting FL *7: Definitions of failure; 1)Lcd luminance becomes half of the minimum value. 2)Lamp doesn’t light normally. *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba Matsushita Display Technology Co., Ltd. or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology Co. Ltd. or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display Technology Co., Ltd. before proceeding with the design of equipment incorporating this product. (1/10) 2006-09-26 (Ver.0.5R) Depth of hole MIN. 0.3 (3.5) 12.8 +/-0.2 3.6 +/-0.2 121.8 +/-0.2 131.52 (Active area) 10.64 +/-0.5 10.0 +/-0.3 Main viewing aqngle direction 1.0 +/-0.2 3.0 +/-0.2 3.0 +/-0.2 1.0 +/-0.2 Depthof Depth of hole hole MIN. 0.6 MIN.1.9 Active area center CN2 BHR-03VS-1(JST) No.3 Pin Low (Black) → No.1 Pin→ High(Red) 30 +/-5 Front side 138.7 (Bezel opening) 6.9 151.0 +/-0.3 Depth of hole MIN. 1.4 142.0 +/-0.2 3.6 +/-0.2 1.3 +/-0.2 4 . -R0 5 4-R 0.3 LTA065A043F DIMENSIONAL OUTLINE (Front figure) Unit : mm Standard tolerance : ±0.5 (30) 1 2 3 26 +/-1 32 +/-1 12.2 +/-0.2 3.6 +/-0.2 88.0 +/-0.2 98.64(Active area) 9.48 +/-0.5 2.6 +/-0.2 1.0 +/-0.2 103.7(Bezel opening) 6.5 115.5 +/-0.3 1.0 +/-0.2 3.5 +/-0.2 88.0 +/-0.2 12.2 +/-0.2 3.6 +/-0.2 (2/10) 2006-09-26 (Ver.0.5R) 4-φ1 .6 +/-0 .05 Depth 3 .0 +/-0 .3 (2-φ4 Ho les for in ject ing res in) φ5 +/-0 .3 Ho le ( Bor ing to re frect ive sheet ) 38.0 +/-0.5 Area of depth is 10.0 +/-0.3 (112.7) (4-R1) (19.3) (0.8) (126) (12.5) 145.4 2.8 (R1) (0.8) (4.7) (0.8) (R1) (5.1) (R1) (R1) (0.4) Gate FCP Sirial label 1pin Label DC-DC 16pin >PC< (R1) (R1) 1pin Main CN1 高圧 注意 Connector board HIGH VOLTAGE IL-FHR-BF40S-HF inserting (JAE) direction (R1) (R1) 40pin (R1) (R1) (R2) (R2) Source FPC 9+/-1 Area of the insulated sheet LTA065A043F (Back figure) Unit : mm Standard tolerance : ±0.5 98.4 14.3 (66.4) (11.9) (9.5) (13.7) 17 +/-0.5 40 +/-1 (1.8) (2.7) (2.7) 1pin 58pin (11.9) (11.6) (38.5) (51.1) (5.7) (0.3) (3/10) 2006-09-26 (Ver.0.5R) LTA065A043F BLOCK DIAGRAM 640pixels 1,1 X,1 640,1 1,2 X,2 640,2 1,Y X,Y 640,Y 1,480 640,480 X,480 SEQUENCE OF POWER SUPPLIES AND SIGNALS 200ms(min.) 100ms(min.) 90% 90% 30ms(max.) V DD 30ms(max.) 10% 0ms(min.) 10% 0ms(min.) 30ms(max.) CLK 10% 10% DE DATA 2 sec (Min.) Hs,Vs V SFL V FL FL Input Voltage V 10% SFL 10% VFL *1: In case handling Make sure to turn off the power when you plug the cable to the input connector and pull the cable out from the connector. (4/10) 2006-09-26 (Ver.05R) 480pixels LTA065A043F TIMING CHART *1: DE Signal is defined as above timing concerning to the sync. signal of Vs and Hs. This LCD module is designed to be synchronized only by DE signal even when Vs and Hs are inputted. Therefore, make DE signal be low level by all means for the blanking period that effective data aren't inputted. (5/10) 2006-09-26 (Ver.05R) Tv Vs Tvf Tvp Tvf Tvb Hs X,479 DATA invalid X,1 X,2 X,Y invalid X,480 DE Th Hs Thf Thp Thb Thf CLK 639,Y DATA invalid 1,Y 2,Y invalid 640,Y DE DATA VIH DE VIL Hs IH V CLK VIL Tch Tcl Tdh Tds Tes Teh Ths Thh LTA065A043F TIMING CHART (PAL Drive) *1: DE Signal is defined as above timing concerning to the sync. signal of Vs and Hs. This LCD module is designed to be synchronized only by DE signal even when Vs and Hs are inputted. Therefore, make DE signal be low level by all means for the blanking period that effective data aren't inputted. (6/10) 2006-09-26 (Ver.05R) Tv Vs Tvf Tvp Tvf Tvb Hs X,559 invalid X,1 X,2 X,Y-1 X,Y X,Y+1 invalid DATA X,560 DE Th Hs Thp Thf Thb Thf CLK 1,Y-1 639,Y-1 1,Y 639,Y 1,Y+1 639,Y+1 DATA invalid invalid invalid invalid 2,Y-1 640,Y-1 2,Y 640,Y+1 640,Y 2,Y+1 DE Thgs Thgsw GSX1 Thdo Thdow DOFF1 DATA IH V DE VIL Hs IH V CLK VIL Tds Tdh Tch Tcl Teh Tes Thh Ths LTA065A043F TIMING SPECIFICATION *1 Item Symbol Min. Typ. Max. PAL Drive Unit CLK frequency Fck --- 25.175 --- 25.175 MHz (Clock) Period Clk --- 39.72 --- 39.72 us MIN : 12 High Time Tch 12 --- --- ns MIN : 12 Low Time Tcl 12 --- --- ns MIN : 5 DATA Setup Time Tds 5 --- --- ns MIN : 10 (Data) Hold Time Tdh 10 --- --- ns MIN : 5 DE Setup Time Tes 5 --- --- ns MIN : 10 (DataEnable) Hold Time Teh 10 --- --- ns MIN : 5 Hs Setup Time Ths 5 --- --- ns MIN : 10 (Horizontal Sync.) Hold Time Thh 10 --- --- ns 790 800 832 800 Period Th clk 4 96 --- 96 Pulse Width Thp clk --- 13 --- 13 Front Porch Thf clk 7 51 --- 51 Back Porch Thb clk 516 525 534 625 Vs th Period Tv 16.2 16.7 17.6 19.875 (Vertical Sync.) ms 1 2 --- 2 Pulse Width Tvp th --- 11 --- 25 Front Porch Tvf th 4 32 --- 38 Back Porch Thb th *2 GSX1 Start Position Thgs --- --- --- 738 clk (Display period correction signal) Pulse Width Thgsw --- --- --- 990 clk *2 DOFF1 Start Position Thdo --- --- --- 800 clk (Non-display period correction signal) Pulse Width Thdow --- --- --- 800 clk The timing of a clock signal is defined by the connector input terminal part. *1: PAL drive does not guarantee about the timing which does not follow above. A flicker and quality of image may deteriorate a little by PAL drive. Please include in your set and check enough. *2: The start position of each correction signal is defined as the regulation from falling of DE signal before 1Hs of DE signal removed. (7/10) 2006-09-26 (Ver.05R) LTA065A043F CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector：FA5B040HP1 (40 pin-0.5 ㎜ pitch/Gilded type) /Japan Aviation Industry, Limited Terminal № Symbol Function 1 VDD Power Supply : +3.3V 2 VDD Power Supply : +3.3V 3 VDD Power Supply : +3.3V 4 VDD Power Supply : +3.3V 5 VSS GND 1 6 GSX1 Display period compensation signal. * 7 VSS GND 1 8 DOFF1 Non-display period compensation signal. * 9 VSS GND 10 DE Data Enable Signal 11 VSS GND 12 VS Vertical Sync. 13 VSS GND 14 HS Horizontal Sync. 15 VSS GND 16 B5 Blue display data (MSB) 17 B4 Blue display data 18 B3 Blue display data 19 B2 Blue display data 20 B1 Blue display data 21 B0 Blue display data (LSB) 22 VSS GND 23 G5 Green display data (MSB) 24 G4 Green display data 25 G3 Green display data 26 G2 Green display data 27 G1 Green display data 28 G0 Green display data (LSB) 29 VSS GND 30 R5 Red display data (MSB) 31 R4 Red display data 32 R3 Red display data 33 R2 Red display data 34 R1 Red display data 35 R0 Red display data (LSB) 36 VSS GND 37 VSS GND 38 CLK Dot Clock 39 VSS GND 40 VSS GND *1 : It opens, when performing the usual operation. CN2 CCFL POWER SOURCE Connector : BHR-03VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Mating Connector : SM02(8.0)B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function 1 V CCFL Power Supply ( high voltage) FLH 2 2 NC * Non Connection (open) 3 V CCFL Power Supply (low voltage) FLL *2 : NC terminal should be open. (8/10) 2006-09-26 (Ver.05R) LTA065A043F 256k (k=1024) COLOR COMBINATION TABLE Gray Scale Display Level R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Black L L L L L L L L L L L L L L L L L L --- Blue L L L L L L L L L L L L H H H H H H --- Green L L L L L L H H H H H H L L L L L L --- Light Blue Basic L L L L L L H H H H H H H H H H H H --- Color Red H H H H H H L L L L L L L L L L L L --- Purple H H H H H H L L L L L L H H H H H H --- Yellow H H H H H H H H H H H H L L L L L L --- White H H H H H H H H H H H H H H H H H H --- Black L L L L L L L L L L L L L L L L L L L 0 L L L L L H L L L L L L L L L L L L L 1 L L L L H L L L L L L L L L L L L L L 2 Dark Gray ↑ : : : L3… Scale of ↓ : : : L60 Red Light H H H H L H L L L L L L L L L L L L L61 H H H H H L L L L L L L L L L L L L L62 Red H H H H H H L L L L L L L L L L L L Red L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L L L L L L L H L L L L L L L 1 L L L L L L L L L L H L L L L L L L L 2 Dark Gray ↑ : : : L3… Scale of ↓ : : : L60 Green Light L L L L L L H H H H L H L L L L L L L61 L L L L L L H H H H H L L L L L L L L62 Green L L L L L L H H H H H H L L L L L L Green L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L L L L L L L L L L L L L H L 1 L L L L L L L L L L L L L L L L H L L 2 Dark Gray ↑ : : : L3… Scale of ↓ : : : L60 Blue Light L L L L L L L L L L L L H H H H L H L61 L L L L L L L L L L L L H H H H H L L62 Blue L L L L L L L L L L L L H H H H H H Blue L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L H L L L L L H L L L L L H L 1 L L L L H L L L L L H L L L L L H L L 2 Dark Gray Scale of ↑ : : : L3… White & ↓ : : : L60 Black Light H H H H L H H H H H L H H H H H L H L61 H H H H H L H H H H H L H H H H H L L62 White H H H H H H H H H H H H H H H H H H White L63 (9/10) 2006-09-26 (Ver.05R) LTA065A043F ! FOR SAFETY LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information. 1) SPECIAL PURPOSES A) Toshiba Matsushita Display Technology's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life threatening or otherwise catastrophic. B) Since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock that exceed Toshiba's published specification limits. C) In addition, since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba Matsushita Display Technology does not warrant the module, if customer disassembled or modified it. 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) GLASS OF LCD PANEL BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. 5) ELECTRIC SHOCK DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module in order to prevent electric shock, because high voltage is supplied to these parts while power supply is turned on. 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design. 7) RECOMMENDED OPERATION CONDITIONS The performance and quality of the LCD panel are warranted only when the LCD panel is used within “the recommended operation conditions”. Toshiba Matsushita Display Technology Co., Ltd. never warrants the performance and quality of the LCD panel when you use the LCD panel over “the recommended operation conditions”, although within “the absolute maximum rating”. To use the LCD panel over “the recommended operation conditions” may have bad influence on the characteristics and reliability of the LCD panel and may shorten the life of the LCD panel. Therefore, when designing the whole set, not to be over “the recommended operation conditions”, you should fully take care of supply voltage change, characteristic of connection parts, serge of input-and-output line, and surrounding temperature. 8) DISPOSAL When dispose LCD module, obey to the applicable environmental regulations. (10/10) 2006-09-26 (Ver.05R)