P a n e l M ISE, Inc. http://iseinc.com 655 Series The ATC Model 655 timer is an electronic control that will retrofit most round case electromechanical timers. the control performs the same timing modes (ON-Delay or Reverse Start Delay) as electromechanical units, and it is capable of timing ranges from 1 millisecond to 199 hours, 59 min- utes. On the bottom inside of the control are DIP switches which can be set, in seconds, to establish the timing mode and time range. Our unit will plug into competitive mounted cases without wiring changes in most instances. Remove the electromechanical timer, set ours, plug it into the electromechanical timer case and you’re ready to run. DIP switch setting instructions for electromechanical timers are supplied with 655 installation instructions. DIMENSIONS (INCHES/MILLIMETERS) \\\ o • Direct Replacement For Electromechanical Timers • Two Timing Modes • Data Retention with EEPROM Memory or Battery • Five Time Ranges • Simple Keypad Time Setting • Sealed Faceplate model 600-3-3950 surface mounting bracket • Keypad Lockout of Time Setting • Easy Programming • Instantaneous Contacts Directly Track the Control Input ORDERING INFORMATION \\\ MODEL NUMBER DESCRIPTION 655-8-1000 Timer 120VAC W/EEPROM Memory 655-8-1001 Timer 240VAC W/EEPROM Memory WIRING \\\ 655-8-3000 Timer 120 VAC W/Battery Memory internal schematic 655-8-3001 Timer 240 VAC W/Battery Memory 655-8-3000 Timer 120 VAC W/Battery Memory 655-8-3001 Timer 240 VAC W/Battery Memory 652-3-0130 Replacement Lithium Battery 600-3-3950 Base Mounting Bracket Mounting Gasket, 1/8" Thick 651-3-0128 (Included with Timer) Mounting Gasket, 1/4" Thick 651-3-0129 (Included with Timer) 116 u n t e d D i g i t a l T i m e r Panel Mounted Digital Timers // 655 Series ISE, Inc., 10100 Royalton Rd., Cleveland, OH USA Tel: (440) 237-3200 Fax: (440) 237-1744 655 Series DIP SWITCH SETTING GUIDE SPECIFICATIONS–ALL MODELS \\\ \\\ A655 Switch Settings 0.001 SEC to 19.999 SEC Eagle Part Number 12 3456 7 0.01 SEC to 199.99 SEC HP50A6 OO X OOO O TIMING 0.1 SEC to 1999.9 SEC HP50A601 O OXO OX O RANGES 1 SEC to 199 MIN 59 SEC HP51A6 OO X OOO O HP51A601 O OXO OXO 1 MIN to 199 Hr. 59 MIN HP52A6 O X OOOO O TIMING MODES ON-Delay or Reverse Start Delay HP52A601 OXO O OXO RESET TIME 25 mSEC HP53A6 OX XO O O O CONTROL VOLTAGE HP53A601 OX XO OXO 25 mSEC INITIATE TIME HP54A6 OX XO O O O HP54A601 OX XO OXO MEMORY Lithium Battery - Replaceable HP55A6 OX XO O O O POWER 5.2VA HP55A601 O X XO OXO CONSUMPTION HP56A6 OX XO O O O TIME Front Panel Keypad SETTING HP56A601 OX XO OXO TIME REPEAT HP57A6 OX XO O O O ± .005 SEC ACCURACY HP57A601 OX XO OXO DISPLAY LCD: 4-1/2 Digit, 7/16" High HP58A6 X OOOO OO RELAY HP58A601 XO O O OXO 50,000,000 Operations MECHANICAL LIFE HP59A6 X O O OO OO INSTANTANEOUS 7 Amps Resistive, 240 VAC HP59A601 XO O O OXO RELAY 2 N.O., 2 N.C. Contacts HP510A6 X OOOO OO OUTPUT HP510A601 X O O O O XO SHORT CIRCUIT 1/4 Amp Fuse HP511A6 X OOOO OO PROTECTION HP511A601 X O O O OXO TEMPERATURE 32° to 140°F (0° to 60°C) HP514A6 OO X OOO O RATING 120 or 240 VAC, +10%, -20%, HP514A601 O OXO OXO OPERATING POWER 50/60 Hz. HP515A6 OO X OOO O TRANSIENT HP515A601 O OXO OXO VOLTAGE Metal Oxide Varistor HP517A6 O O X O O O O PROTECTION HP517A601 O OXO OXO NEMA HP518A6 OX XO O O O NEMA 12 RATING HP518A601 OX XO OXO TERMINALS Screw Terminals DIP SWITCH DEFINITIONS MOUNTING Plug In Case WEIGHT Net: 25 oz. Shipping: 30 oz. 0=OFF X=ON 1. Determine Eagle Model Number: To 5. Set Timing Mode: To select the timing mode required, set determine the Model Number of the switches 5, 6, and 7 on the switch assembly as recommended Eagle HP5; remove timer from case by the DIP Switch Setting Guide. by loosening the screw at the lower 6. Set Preset Time: Position the 655 control so that you are looking at front of the timer face and lift the the keypad on the front of the unit. Push the SET button and four mounting handle and pull the timer dashes will appear. Depress the SET button a second time and from the case. The model number word SET and four zeros will appear. To enter the preset time will be on the left side of the timer. Some models will have a desired, press the ENT button and preset number will flash seven metal plate with the part number, others have a label with the and go blank. The Model 655 timer in now ready to operate and number in that same area. can be returned to its case or directly into the case of the HP5 2. Remove Control: Remove the 655 control from its case by loos- that it is replacing. To check or change the preset time; push the ening the screw at the bottom of the chrome handle, lifting the SET button and time setting will be displayed. To change the pre- handle up and pulling the control forward. set time follow the same procedure as indicated previously in this paragraph. When you have completed setting a new preset time, 3. Determine Switch Settings: Determine how the 655 DIP switches push the ENT button. The preset time can be changed when the should be set to retrofit that particular HP5 model using the 655 is running a cycle or "on the fly". That run cycle will be com- DIP Switch Setting Guide. pleted based on the preset at the beginning of the cycle. The new preset will control the next cycle. 4. Set Time Base: Hold the control to expose the DIP switch assem- bly on the bottom of unit and set the time base you require on NOTE: If the "SET" button is pushed to review or change the preset time, the ENT button switches 1, 2, and 3. must be pushed to return the control to the operating mode. 117 655 Series Panel Mounted Digital Timer //