Universal Serial Bus (USB2.0) Compliance Test Package TDSUSB2 Features & Benefits Fully Compliant with USB-IF Tests for USB2.0 Compliance Testing Automated Eye Diagram Analysis Verifies Signal Quality Automated Oscilloscope Setups for Various Tests Eliminates Time Consuming Manual Setups Comprehensive Test Fixture Enables Quick Setup for a Wide Range of Tests High-speed Tests: Signal Quality, Receiver Sensitivity, Chirp, Reset, Resume, Suspend, Packet Parameter and Monotonicity Test Automatic Rise and Fall Time Measurements Simplify Tests Automatic Deskew for Accurate Measurements Online Help Fully Documents Test Procedures User-configurable Report Formats for Customization User-configurable Measurement Limits for Tolerance Testing USB2.0 Physical Layer Verification and Compliance Test Package Applications Engineers involved in design, character- Quick Pass/Fail tests substantiated with USB2.0 Physical Layer Verification ization and validation of USB2.0 devices results make the TDSUSB2 application and Compliance Testing face daily pressures to speed new products the preferred solution for USB2.0 physical Characterize the Quality of to the marketplace. USB2.0 designers layer validation. In-depth analysis is USB2.0 Designs need tools to properly characterize their possible with the statistical information designs and verify compliance to industry about the tests performed. The user- standards. Characterization of these defined measurement limits also help to electrical signals includes mask testing as perform tolerance testing on a design. well as parametric testing, up to 480 Mbps. TDSUSB2 comes on a CD and can TDSUSB2 eliminates the tedium of be easily installed by the user. After manually setting up the oscilloscope by installation, the application is accessible providing predefined oscilloscope setups from the menu bar of the Tektronix for various tests. Users can quickly Windows oscilloscopes. perform all USB-IF recommended tests, such as eye diagram and parametric testing for low-speed, full-speed and high-speed hosts, devices and hubs. The comprehensive test fixture supports a wide range of tests. Universal Serial Bus (USB2.0) Compliance Test Package TDSUSB2 USB2.0 Compliance Test Fixture (TDSUSBF). Measurement Select menu for the Signal Integrity test. Tektronix Digital Oscilloscopes Compliance Test Fixture Characteristics Required For High-speed – A comprehensive compliance test Specifications A Tektronix Windows real-time oscilloscope with TDSUSB2 Tests – Host, hubs and devices. fixture provides a probing solution for bandwidth greater than 2 GHz. Signal Quality Test – the Signal Quality test, Inrush Current For Low-speed and Full-speed – Eye diagram test, jitter (JK, KJ and consecutive), check, Drop and Droop test, Receiver A Tektronix Windows real-time oscilloscope with cross over voltage range, signal rate, end of packet bandwidth greater than 350 MHz. width, rise time, fall time. Sensitivity and Impedance Measurement Tektronix real-time oscilloscope series with these High-speed Tests – test. Connectors are available for the specifications are shown in the Ordering Information Receiver sensitivity, chirp, reset, resume, suspend, data generator and Tektronix DSA8200 section. packet parameter and monotonicity test. sampling oscilloscope with TDR module. Inrush Current Check – USB2.0 Complete Solution Coulombs and capacitance readout. The test fixture is an accessory of The following components make up the complete Droop Test – Volts readout. USB2.0 testing solution for the physical layer TDSUSB2 and is ordered separately. Speed Selection – measurements and compliance testing. Low-speed (LS), full-speed (FS) and high-speed (HS). Signal Direction – Upstream and downstream. Test Point Selection – Near end and far end. Report Generation Format – Plugfest, user specific and Tektronix format. Accessories • www.tektronix.com/accessories 2 Universal Serial Bus (USB2.0) Compliance Test Package TDSUSB2 Ordering Information TDSUSB2 *1 For new TDS5034B, DPO7000, DPO/DSA70000 As an upgrade to TDS5000B, TDS6000/B/C, Series Instrument Orders TDS/CSA7000B, DPO7000, DPO/DSA70000 Series Instruments For Test Fixture ONLY TDSUSBF TDSUSBF For Test Software ONLY Opt. USB TDS5B/6B/7BUP; CSA7BUP; DPO7UP; Opt. USB For Software AND Hardware Opts. USB and TDSUSBF Opts. USB and TDSUSBF Probes TDR Measurements (for Ordering Information Impedance Measurement Test) Voltage Probes System Requirements Tektronix DSA8200 Sampling Oscilloscope with *2 P6248 – High Bandwidth Differential Probe. TDR Sampling Module. For TDSUSB2 Software with a new Tektronix P6330 – High Bandwidth Differential Probe. Windows Oscilloscopes – TDS5034B, DPO7000, *1 TDS5000B Series – Opt. USB is not available for 2-channel DPO/DSA70000 Series oscilloscopes. Legacy P6245 – High Bandwidth Single-ended Active oscilloscope models. models of Tektronix Windows oscilloscopes with Probe. comparable or higher bandwidth specifications *2 The P6248 probe is approved for compliance testing, are also supported. For DPO7000 Series higher performance differential probes may be used for design applications. P6248 (requires TPA-BNC Adapter on DPO7000 TDSUSB2 Recommended Series models). Accessories P6330 (requires TPA-BNC Adapter on DPO7000 Signal Source (for Receiver Series models). Sensitivity Tests) TAP1500 or P6245 (requires TPA-BNC Adapter DTG5274 or DTG5078 and a DTGM 21 Output on DPO7000 Series models). module – Data Generator. Current Probes or AWG7000 Series – Arbitrary Waveform Generator. TCP202 TDSUSBF – USB2.0 test fixture. Ordered For DPO7000 Series separately from TDSUSB. TCP0030, or TCP202 (requires TPA-BNC Adapter on DPO7000 series models). Accessories • www.tektronix.com/accessories 3 Contact Tektronix: Universal Serial Bus (USB2.0) Compliance Test Package ASEAN / Australasia (65) 6356 3900 TDSUSB2 Austria +41 52 675 3777 Balkan, Israel, South Africa and other ISE Countries +41 52 675 3777 Belgium 07 81 60166 Brazil & South America (11) 40669400 Canada 1 (800) 661-5625 Central East Europe, Ukraine and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401 Finland +41 52 675 3777 France +33 (0) 1 69 86 81 81 Germany +49 (221) 94 77 400 Hong Kong (852) 2585-6688 India (91) 80-22275577 Italy +39 (02) 25086 1 Japan 81 (3) 6714-3010 Luxembourg +44 (0) 1344 392400 Mexico, Central America & Caribbean 52 (55) 5424700 Middle East, Asia and North Africa +41 52 675 3777 The Netherlands 090 02 021797 Norway 800 16098 People’s Republic of China 86 (10) 6235 1230 Poland +41 52 675 3777 Portugal 80 08 12370 Republic of Korea 82 (2) 528-5299 Russia & CIS +7 (495) 7484900 South Africa +27 11 254 8360 Spain (+34) 901 988 054 Sweden 020 08 80371 Switzerland +41 52 675 3777 Taiwan 886 (2) 2722-9622 United Kingdom & Eire +44 (0) 1344 392400 USA 1 (800) 426-2200 For other areas contact Tektronix, Inc. at: 1 (503) 627-7111 Updated 15 September 2006 Our most up-to-date product information is available at: www.tektronix.com Copyright © 2007, Tektronix. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks or registered trademarks of their respective companies. 3/07 HB/WOW 61W-14858-7