TECCOR Q8004V4
Description
TRIAC 800V 4A TO-251
Part Number
Q8004V4
Price
Request Quote
Manufacturer
TECCOR
Lead Time
Request Quote
Category
PRODUCTS - Q
Datasheet
Extracted Text
E2 TO TO- -9 92 2 *TO-220 TO-202 3-lead Compak TO-263 2 D Pak TO-252 D-Pak *TO-3 TO-251 MT2 MT1 Fastpak V-Pak G Triacs RoHS (0.8 A to 35 A) E2 General Description These gated triacs from Teccor Electronics are part of a broad line of bidirectional semiconductors. The devices range in current ratings from 0.8 A to 35 A and in voltages from 200 V to 1000 V. The triac may be gate triggered from a blocking to conduction Features state for either polarity of applied voltage and is designed for AC switching and phase control applications such as speed and tem- •RoHS Compliant perature modulation controls, lighting controls, and static switch- • Electrically-isolated packages ing relays. The triggering signal is normally applied between the • Glass-passivated junctions gate and MT1. • Voltage capability — up to 1000 V Isolated packages are offered with internal construction, having • Surge capability — up to 200 A the case or mounting tab electrically isolated from the semicon- ductor chip. This feature facilitates the use of low-cost assembly and convenient packaging techniques. Tape-and-reel capability Compak Package is available. See “Packing Options” section of this catalog. • Surface mount package — 0.8 A and 1 A series All Teccor triacs have glass-passivated junctions to ensure long- • New small profile three-leaded Compak package term device reliability and parameter stability. Teccor's glass- passivated junctions offer a rugged, reliable barrier against junc- • Packaged in embossed carrier tape with 2,500 tion contamination. devices per reel • Can replace SOT-223 Variations of devices covered in this data sheet are available for custom design applications. Consult factory for more information. ©2004 Littelfuse, Inc. E2 - 1 http://www.littelfuse.com Thyristor Product Catalog +1 972-580-7777 * Selected Packages U.L. RECOGNIZED File #E71639 Triacs Data Sheets Part Number I V I T(RMS) Isolated Non-isolated DRM GT (4) (1) (3) (7) (15) MT2 MT2 MT2 G MT2 MT2 G G MT2 MT2 MT1 MT1 MT1 MT2 G MT2 G MT1 MT1 MT1 G MT1 G MT1 G MT2 MT2 MT2 MT2 Volts mAmps TO-252 TO-251 TO-263 2 TO-92 TO-220 Compak TO-202 TO-220 D-Pak V-Pak D Pak QI QII QIII QIV QIV MAX See “Package Dimensions” section for variations. (11) MIN MAX TYP Q2X8E3 Q2X3 200 10 10 10 25 0.8 A Q4X8E3 Q4X3 400 10 10 10 25 Q6X8E3 Q6X3 600 10 10 10 25 Q2X8E4 Q2X4 200 25 25 25 50 Q4X8E4 Q4X4 400 25 25 25 50 Q6X8E4 Q6X4 600 25 25 25 50 Q201E3 Q2N3 200 10 10 10 25 1A Q401E3 Q4N3 400 10 10 10 25 Q601E3 Q6N3 600 10 10 10 25 Q201E4 Q2N4 200 25 25 25 50 Q401E4 Q4N4 400 25 25 25 50 Q601E4 Q6N4 600 25 25 25 50 Q2004L3 Q2004F31 Q2004D3 Q2004V3 200 10 10 10 25 4A Q4004L3 Q4004F31 Q4004D3 Q4004V3 400 10 10 10 25 Q6004L3 Q6004F31 Q6004D3 Q6004V3 600 10 10 10 25 Q2004L4 Q2004F41 Q2004D4 Q2004V4 200 25 25 25 50 Q4004L4 Q4004F41 Q4004D4 Q4004V4 400 25 25 25 50 Q6004L4 Q6004F41 Q6004D4 Q6004V4 600 25 25 25 50 Q8004L4 Q8004D4 Q8004V4 800 25 25 25 50 QK004L4 QK004D4 QK004V4 1000 25 25 25 50 Q2006L4 Q2006F41 Q2006R4 Q2006N4 200 25 25 25 50 6A Q4006L4 Q4006F41 Q4006R4 Q4006N4 400 25 25 25 50 Q6006L5 Q6006F51 Q6006R5 Q6006N5 600 50 50 50 75 Q8006L5 Q8006R5 Q8006N5 800 50 50 50 75 QK006L5 QK006R5 QK006N5 1000 50 50 50 75 8A Q2008L4 Q2008F41 Q2008R4 Q2008N4 200 25 25 25 50 Q4008L4 Q4008F41 Q4008R4 Q4008N4 400 25 25 25 50 Q6008L5 Q6008F51 Q6008R5 Q6008N5 600 50 50 50 75 Q8008L5 Q8008R5 Q8008N5 800 50 50 50 75 QK008L5 QK008R5 QK008N5 1000 50 50 50 75 See “General Notes” on page E2 - 4 and “Electrical Specification Notes” on page E2 - 5. http://www.littelfuse.com E2 - 2 ©2004 Littelfuse, Inc. +1 972-580-7777 Thyristor Product Catalog Data Sheets Triacs 2 I V V I I P P I t DRM TM GT H GTM GM G(AV) TSM dv/dt(c) dv/dt gt I t di/dt (1) (16) (1) (5) (2) (6) (1) (8) (14) (14) (9) (13) (1) (4) (13) (1) (10) (15) (18) (12) (19) mAmps Volts Volts Amps Volts/µSec T = T = T = T = T = T = T = C C C C C C C 2 mAmps Amps Watts Watts Volts/µSec µSec Amp Sec Amps/µSec 25 °C 100 °C 125 °C 25 °C 25 °C 60/50 Hz 100 °C 125 °C MAX MAX MAX MAX TYP MIN TYP 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 40 30 2.5 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 35 25 2.5 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 25 15 2.5 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 50 40 3 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 45 35 3 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 35 25 3 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 40 30 2.5 1.6 30 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 40 30 2.5 1.6 30 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 30 20 2.5 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 50 40 3 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 50 40 3 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 40 30 3 1.6 30 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 50 40 2.5 12.5 50 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 50 40 2.5 12.5 50 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 40 30 2.5 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 100 75 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 100 75 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 75 50 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 60 40 3 12.5 50 0.05 3 1.6 2.5 30 1.2 15 0.3 55/46 2 50 3 12.5 50 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 200 120 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 200 120 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 150 100 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 125 85 3 26.5 70 0.05 3 1.6 2.5 50 1.6 18 0.5 80/65 4 100 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 250 150 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 250 150 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 220 125 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 150 100 3 41 70 0.05 3 1.6 2.5 50 1.8 20 0.5 100/83 4 100 3 41 70 See “General Notes” on page E2 - 4 and “Electrical Specification Notes” on page E2 - 5. ©2004 Littelfuse, Inc. E2 - 3 http://www.littelfuse.com Thyristor Product Catalog +1 972-580-7777 Triacs Data Sheets Part Number I V I I T(RMS) Isolated Non-isolated DRM GT DRM (4) (16) (1) (3) (7) (15) (1) (16) MT2 MT2 MT1 MT2 MT2 G MT2 MT1 G G MT1 MT1 G Gate MT2 MT1 MT2 MT2 mAmps mAmps TO-3 TO-263 T = T = T = C C C 2 Fastpak TO-220 TO-202 TO-220 D Pak Volts QI QII QIII QIV QIV 25 °C 100 °C 125 °C MAX See “Package Dimensions” section for variations. (11) MIN MAX TYP MAX Q2010L4 Q2010R4 Q2010N4 200 25 25 25 50 0.05 1 Q4010L4 Q4010R4 Q4010N4 400 25 25 25 50 0.05 1 Q6010L4 Q6010R4 Q6010N4 600 25 25 25 50 0.05 1 Q8010L4 Q8010R4 Q8010N4 800 25 25 25 50 0.1 1 10 A QK010L4 QK010R4 QK010N4 1000 25 25 25 50 0.1 3 Q2010L5 Q2010F51 Q2010R5 Q2010N5 200 50 50 50 75 0.05 0.5 2 Q4010L5 Q4010F51 Q4010R5 Q4010N5 400 50 50 50 75 0.05 0.5 2 Q6010L5 Q6010F51 Q6010R5 Q6010N5 600 50 50 50 75 0.05 0.5 2 Q8010L5 Q8010R5 Q8010N5 800 50 50 50 75 0.1 0.5 2 QK010L5 QK010R5 QK010N5 1000 50 50 50 75 0.1 3 Q2015L5 Q2015R5 Q2015N5 200 50 50 50 0.05 0.5 2 Q4015L5 Q4015R5 Q4015N5 400 50 50 50 0.05 0.5 2 15 A Q6015L5 Q6015R5 Q6015N5 600 50 50 50 0.05 0.5 2 Q8015L5 Q8015R5 Q8015N5 800 50 50 50 0.1 1 3 QK015L5 QK015R5 QK015N5 1000 50 50 50 0.1 3 Q2025R5 Q2025N5 200 50 50 50 0.1 1 3 Q4025R5 Q4025N5 400 50 50 50 0.1 1 3 Q6025R5 Q6025N5 600 50 50 50 0.1 1 3 Q8025R5 Q8025N5 800 50 50 50 0.1 1 3 25 A QK025R5 QK025N5 1000 50 50 50 0.1 3 Q6025P5 600 50 50 50 120 0.1 5 Q8025P5 800 50 50 50 120 0.1 5 35 A Q6035P5 600 50 50 50 120 0.1 5 Q8035P5 800 50 50 50 120 0.1 5 V — Repetitive peak blocking voltage Specific Test Conditions DRM V — DC gate trigger voltage; V = 12 V dc; R = 60 Ω GT D L di/dt — Maximum rate-of-change of on-state current; I = 200 mA with GT V — Peak on-state voltage at maximum rated RMS current TM ≤0.1 µs rise time dv/dt — Critical rate-of-rise of off-state voltage at rated V gate open DRM General Notes dv/dt(c) — Critical rate-of-rise of commutation voltage at rated V DRM and I commutating di/dt = 0.54 rated I /ms; gate T(RMS) T(RMS) • All measurements are made at 60 Hz with a resistive load at an unenergized ambient temperature of +25 °C unless specified otherwise. 2 I t — RMS surge (non-repetitive) on-state current for period of 8.3 ms • Operating temperature range (T ) is -65 °C to +125 °C for TO-92, J for fusing -25 °C to +125 °C for Fastpak, and -40 °C to +125 °C for all other I — Peak off-state current, gate open; V = maximum rated value devices. DRM DRM I — DC gate trigger current in specific operating quadrants; • Storage temperature range (T ) is -65 °C to +150 °C for TO-92, GT S V = 12 V dc -40 °C to +150 °C for TO-202, and -40 °C to +125 °C for all other D devices. I — Peak gate trigger current GTM • Lead solder temperature is a maximum of 230 °C for 10 seconds, I — Holding current (DC); gate open H maximum; ≥1/16" (1.59 mm) from case. I — RMS on-state current conduction angle of 360° T(RMS) • The case temperature (T ) is measured as shown on the dimen- C I — Peak one-cycle surge TSM sional outline drawings. See “Package Dimensions” section of this P — Average gate power dissipation G(AV) catalog. P — Peak gate power dissipation; I ≤ I GM GT GTM t — Gate controlled turn-on time; I = 200 mA with 0.1 µs rise time gt GT http://www.littelfuse.com E2 - 4 ©2004 Littelfuse, Inc. +1 972-580-7777 Thyristor Product Catalog Data Sheets Triacs 2 V V I I P P I t dv/dt(c) dv/dt I t di/dt TM GT H GTM GM G(AV) TSM gt (1) (5) (2) (6) (15) (1) (8) (12) (14) (14) (9) (13) (1) (4) (13) (1) (10) (17) (18) (19) Volts Volts Amps Volts/µSec T = T = C C 2 mAmps Amps Watts Watts Volts/µSec µSec Amps Sec Amps/µSec T = 25 °C T = 25 °C 60/50 Hz 100 °C 125 °C C C MAX MAX MAX TYP MIN TYP 1.6 2.5 35 1.8 20 0.5 120/100 2 150 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 150 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 100 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 75 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 50 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 350 225 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 350 225 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 300 200 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 250 175 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 150 3 60 70 1.6 2.5 70 2 20 0.5 200/167 4 400 275 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 400 275 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 350 225 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 300 200 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 200 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 400 275 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 400 275 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 350 225 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 300 200 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 200 4 166 100 1.4 2.75 50 2 20 0.5 250/220 5 550 475 3 260 100 1.4 2.75 50 2 20 0.5 250/220 5 450 400 3 260 100 1.5 2.75 50 2 20 0.5 350/300 5 550 475 3 508 100 1.5 2.75 50 2 20 0.5 350/300 5 450 400 3 508 100 (15) R = 60 Ω for 0.8 A to10 A triacs; R = 30 Ω for 15 A to 35 A triacs Electrical Specification Notes L L (16) T = T for test conditions in off state C J (1) For either polarity of MT2 with reference to MT1 terminal (17) I = 300 mA for 25 A and 35 A devices GT (2) For either polarity of gate voltage (V ) with reference to MT1 GT (18) Quadrants I, II, III only terminal (19) Minimum non-trigger V at 125 °C is 0.2 V for all except 50 mA (3) See Gate Characteristics and Definition of Quadrants. GT MAX QIV devices which are 0.2 V at 110 °C. (4) See Figure E2.1 through Figure E2.7 for current rating at specific operating temperature. Gate Characteristics (5) See Figure E2.8 through Figure E2.10 for i versus v T T. (6) See Figure E2.12 for V versus T . GT C Teccor triacs may be turned on between gate and MT1 terminals in the following ways: (7) See Figure E2.11 for I versus T . GT C • In-phase signals (with standard AC line) using Quadrants I (8) See Figure E2.14 for I versus T . H C and III (9) See Figure E2.13 for surge rating with specific durations. • Application of unipolar pulses (gate always positive or nega- (10) See Figure E2.15 for t versus I . gt GT tive), using Quadrants II and III with negative gate pulses and (11) See package outlines for lead form configurations. When ordering Quadrants I and IV with positive gate pulses special lead forming, add type number as suffix to part number. However, due to higher gate requirements for Quadrant IV, it (12) Initial on-state current = 200 mA dc for 0.8 A to10 A devices, 400 mA dc for 15 A to 35 A devices is recommended that only negative pulses be applied. If pos- itive pulses are required, see “Sensitive Triacs” section of (13) See Figure E2.1 through Figure E2.6 for maximum allowable case this catalog or contact the factory. Also, see temperature at maximum rated current. Figure AN1002.8, “Amplified Gate” Thyristor Circuit. (14) Pulse width ≤10 µs; I ≤ I GT GTM ©2004 Littelfuse, Inc. E2 - 5 http://www.littelfuse.com Thyristor Product Catalog +1 972-580-7777 Triacs Data Sheets In all cases, if maximum surge capability is required, pulses Electrical Isolation should be a minimum of one magnitude above I rating with a GT Teccor’s isolated triac packages will withstand a minimum high steep rising waveform (≤1 µs rise time). potential test of 2500 V ac rms from leads to mounting tab or base, over the operating temperature range of the device. The ALL POLARITIES ARE REFERENCED TO MT1 following isolation table shows standard and optional isolation MT2 POSITIVE ratings. (Positive Half Cycle) MT2 MT2 + (-) I (+) I GT Electrical Isolation GT GATE GATE from Leads to Mounting Tab * TO-220 Fastpak MT1 MT1 VAC RMS Isolated Isolated REF 2500 Standard Standard REF QII QI I - + I 4000 Optional ** N/A GT GT QIII QIV MT2 MT2 * UL Recognized File E71639 ** For 4000 V isolation, use V suffix in part number. (-) I (+) I GT GT GATE GATE MT1 MT1 - REF MT2 NEGATIVE REF (Negative Half Cycle) Definition of Quadrants Thermal Resistance (Steady State) R [R ] (TYP.) °C/W θ JC θ JA Package Code PE C F F2 L R D V N Type TO-3 TO-202 TO-202 TO-220 TO-220 TO-252 TO-251 TO-263 2 D-Pak V-Pak Fastpak TO-92 Compak Type 1 Type 2 Isolated Non-isolated D Pak 0.8 A 60 [135] 60 * 1 A 50 [95] 40 * 4A 3.5 [45] 6 [70] 3.6 [50] 3.5 6.0 [70] 6 A 3.8 3.3 1.8 [45] 1.8 8A 3.3 2.8 1.5 1.5 10 A 3.5 2.6 1.3 1.3 15 A 2.1 1.1 1.1 25 A 1.6 0.89 0.89 35 A 1.5 2 * Mounted on 1 cm copper foil surface; two-ounce copper foil http://www.littelfuse.com E2 - 6 ©2004 Littelfuse, Inc. +1 972-580-7777 Thyristor Product Catalog 15 A TO-220 (Non-isolated) 2 15 A D Pak 15 A TO-220 (Isolated) Data Sheets Triacs 130 130 CURRENT WAVEFORM: Sinusoidal 120 120 LOAD: Resistive or Inductive 10 A TO-220 (Non-isolated) CONDUCTION ANGLE: 360 2 ˚ 10 A D Pak 110 CASE TEMPERATURE: Measured 110 as shown on Dimensional Drawing 100 100 10 A TO-202 90 1 A 90 80 80 0.8 A CURRENT WAVEFORM: Sinusoidal 70 70 LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 ˚ CASE TEMPERATURE: Measured as 60 60 shown on Dimensional Drawing 0 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 02468 10 12 14 RMS On-state Current [l ] – AMPS RMS On-state Current [l ] – Amps T(RMS) T(RMS) Figure E2.1 Maximum Allowable Case Temperature versus On-state Figure E2.4 Maximum Allowable Case Temperature versus Current (0.8 A and 1 A) On-state Current (10 A) 130 130 6 A TO-220 (Non-isolated) 2 6 A D Pak 120 120 6 A TO-220 (Isolated) 110 110 6 A TO-202 100 100 90 4 A TO-202 (TYPE 2 and 4) 90 4 A TO-251 80 80 4 A TO-220 (Isolated) 4 A TO-202 (Type 1 and 3) CURRENT WAVEFORM: Sinusoidal 4 A TO-252 70 70 LOAD: Resistive or Inductive CURRENT WAVEFORM: Sinusoidal CONDUCTION ANGLE: 360 LOAD: Resistive or Inductive ˚ 60 CASE TEMPERATURE: Measured as 60 CONDUCTION ANGLE: 360 ˚ shown on Dimensional Drawing CASE TEMPERATURE: Measured as shown on Dimensional Drawing 0 0 01234567 0 5 10 15 RMS On-state Current [l ] – Amps RMS On-state Current [l ] – AMPS T(RMS) T(RMS) Figure E2.2 Maximum Allowable Case Temperature versus On-state Figure E2.5 Maximum Allowable Case Temperature versus Current (4 A and 6 A) On-state Current (15 A) 130 CURRENT WAVEFORM: Sinusoidal 130 LOAD: Resistive or Inductive 120 CONDUCTION ANGLE: 360˚ 10 A TO-220 (Isolated) CASE TEMPERATURE: Measured as 120 shown on Dimensional Drawing 8 A TO-220 (Non-isolated) 2 110 8 A D Pak 110 25 A TO-220 (Non-isolated) 100 2 100 25 A D Pak 8 A TO-202 8 A TO-220 (Isolated) 90 90 25 A TO-3 Fastpak 80 80 35 A TO-3 Fastpak CURRENT WAVEFORM: Sinusoidal 70 LOAD: Resistive or Inductive 70 CONDUCTION ANGLE: 360 ˚ 60 CASE TEMPERATURE: Measured as shown on Dimensional Drawing 60 0 0246810 12 14 50 0 1020304050 RMS On-state Current [l ] – AMPS T(RMS) RMS On-state Current [l ] – Amps T(RMS) Figure E2.3 Maximum Allowable Case Temperature versus Figure E2.6 Maximum Allowable Case Temperature versus On-state Current (8 A and 10 A) On-state Current (25 A and 35 A) ©2004 Littelfuse, Inc. E2 - 7 http://www.littelfuse.com Thyristor Product Catalog +1 972-580-7777 Maximum Allowable Case Temperature (T ) – ˚C C Maximum Allowable Case Temperature (T ) – C Maximum Allowable Case Temperature (T ) – C C ˚ C ˚ Maximum Allowable Case Temperature (T ) – ˚C C Maximum Allowable Case Temperature (T ) – ˚C Maximum Allowable Case Temperature (T ) – ˚C C C Triacs Data Sheets 90 120 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive T = 25 ˚C C 70 CONDUCTION ANGLE: 360 ˚ 100 FREE AIR RATING – NO HEATSINK 60 80 TO-202 (TYPE 2 and 4) 50 TO-251 40 TO-220 Devices and 25 A and 35 A Fastpak TO-202 (Type 1 and 3) 60 30 1 A TO-92 20 40 15 A and 25 A 10 0.8 A TO-92 25 20 0 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 RMS On-state Current [I ] — Amps Positive or Negative Instantaneous On-state Voltage (v ) – Volts T (RMS) T Figure E2.7 Maximum Allowable Ambient Temperature versus Figure E2.10 On-state Current versus On-state Voltage (Typical) On-state Current (15 A and 25 A) 4.0 10 9 T = 25 ˚C C 8 3.0 7 6 5 2.0 1 A 4 3 1.0 2 0.8 A 1 0 -65 -40 -15 +25 +65 +125 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Positive or Negative Instantaneous On-state Voltage (v ) – Volts Case Temperature (T ) – ˚C T C Figure E2.8 On-state Current versus On-state Voltage (Typical) Figure E2.11 Normalized DC Gate Trigger Current for All Quadrants (0.8 A and 1 A) versus Case Temperature 20 2.0 T = 25 ˚C C 18 16 1.5 6-10 A 14 12 4A 10 1.0 8 6 .5 4 2 0 0 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -65 -40 -15 +25 +65 +125 Positive or Negative Instantaneous On-state Voltage (v ) – Volts Case Temperature (T ) – ˚C T C Figure E2.9 On-state Current versus On-state Voltage (Typical) Figure E2.12 Normalized DC Gate Trigger Voltage for All Quadrants (4 A, 6 A, 8 A, and 10 A) versus Case Temperature http://www.littelfuse.com E2 - 8 ©2004 Littelfuse, Inc. +1 972-580-7777 Thyristor Product Catalog Positive or Negative Instantaneous On-state Current (i ) – Amps T Maximum Allowable Ambient Temperature (T ) — ˚C A Positive or Negative Instantaneous On-state Current (i ) – Amps T Positive or Negative Instantaneous V GT On-state Current (i ) – Amps T Ratio of I GT V (T = 25 ˚C) GT C Ratio of I (T = 25 ˚C) GT C 1 A 4 A 0.8 A 8 A 6 A 35 A Fastpak 25 A Fastpak 25 A TO-220 15 A 10 A Data Sheets Triacs 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT [l ]: Maximum T(RMS) Rated Value at Specified Case Temperature 400 NOTES: 1) Gate control may be lost during and immediately following surge current interval. 300 2) Overload may not be repeated until junction temperature has returned to steady-state rated value. 200 120 100 80 60 50 40 30 20 10 1 1 10 100 1000 Surge Current Duration – Full Cycles Figure E2.13 Peak Surge Current versus Surge Current Duration 4.0 8 Devices with l = 10 mA GT INITIAL ON-STATE CURRENT 7 = 200 mA DC 0.8 A - 10 A Devices Devices with l = 25 mA GT = 400 mA DC 15 A - 25 A Devices T = 25 ˚C C 3.0 6 Devices with l = 50 mA GT 5 4 2.0 3 2 1.0 1 0 0 25 50 75 100 125 150 175 200 225 250 275 300 -65 -40 -15 +25 +65 +125 DC Gate Trigger Current (l ) – mA Case Temperature (T ) – ˚C GT C Figure E2.14 Normalized DC Holding Current versus Case Temperature Figure E2.15 Turn-on Time versus Gate Trigger Current (Typical) ©2004 Littelfuse, Inc. E2 - 9 http://www.littelfuse.com Thyristor Product Catalog +1 972-580-7777 I H Ratio of I (T = 25 ˚C) H C Peak Surge (Non-repetitive) On-state Current (l ) – Amps TSM Typical Turn-on Time (t ) – µSec gt Triacs Data Sheets 4.0 CURRENT WAVEFORM: Sinusoidal CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive LOAD: Resistive or Inductive 1.5 CONDUCTION ANGLE: 360˚ CONDUCTION ANGLE: 360˚ 3.0 1.0 0.8 A 2.0 1 A 0.5 4 A 1.0 0 0 0 0.25 0.50 0.75 1.0 1.25 0 1.0 2.0 3.0 4.0 RMS On-state Current [I ] – Amps T(RMS) RMS On-state Current [I ] – Amps T(RMS) Figure E2.16 Power Dissipation (Typical) versus On-state Current Figure E2.19 Power Dissipation (Typical) versus RMS On-state Current (0.8 A and 1 A) (4 A) 18 16 15 A 14 12 6-10 A 10 8 6 4 CURRENT WAVEFORM: Sinusoidal 2 LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ 0 0123456789 10 11 12 13 14 15 16 RMS On-state Current [l ] – Amps T(RMS) Figure E2.17 Power Dissipation (Typical) versus On-state Current (6 A to 10 A and 15 A) 45 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive 40 CONDUCTION ANGLE: 360˚ 35 30 25 A 25 20 25 A - 35 A Fastpaks 15 10 5 0 0 8 16 24 32 40 RMS On-state Current [l ] – Amps T(RMS) Figure E2.18 Power Dissipation (Typical) versus On-state Current (25 A to 35 A) http://www.littelfuse.com E2 - 10 ©2004 Littelfuse, Inc. +1 972-580-7777 Thyristor Product Catalog Average On-state Power Dissipation Average On-state Power Dissipation [P ] – Watts [P ] – Watts D(AV) Average On-state Power Dissipation [P ] – Watts D(AV) D(AV) Average On-state Power Dissipation [P ] – Watts D(AV)
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the Q8004V4 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers

What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods