TECCOR P3203ZC

Four-port Balanced Three-chip Protector Four-port Balanced Three-chip Protector This hybrid Single In-line Package (SIP) protects four twisted pairs from overcurrent and overvoltage conditions. Comprised of twelve discrete DO-214AA SIDACtor devices and eight TeleLink surface mount fuses, it is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. Surge current ratings up to 500 A are available. F2 F4 F6 F8 Tip 2 5 Tip 7 10 Tip 12 15 Tip 17 20 Z12 Z3 Z6 Z9 Z2 Z5 Z8 Z11 Gnd 3 Gnd 8 Gnd 13 Gnd 18 Z10 Z1 Z7 Z4 Ring 4 1 Ring 9 6 Ring 14 11 Ring 19 16 F1 F3 F5 F7 Electrical Parameters V V V V C DRM S DRM S O Volts Volts Volts Volts pF Pins 2-3, 4-3, 7-8, 9-8, Part 12-13, 14-13, 17-18, Pins 2-4, 7-9, V I I I I T DRM S T H Number * 19-18 12-14, 17-19 Volts µAmps mAmps Amps mAmps Pins 1-3 P1553Z_ 130 180 130 180 8 5 800 2.2 150 40 P1803Z_ 150 210 150 210 8 5 800 2.2 150 40 P2103Z_ 170 250 170 250 8 5 800 2.2 150 40 P2353Z_ 200 270 200 270 8 5 800 2.2 150 40 P2703Z_ 230 300 230 300 8 5 800 2.2 150 30 P3203Z_ 270 350 270 350 8 5 800 2.2 150 30 P3403Z_ 300 400 300 400 8 5 800 2.2 150 30 A2106Z_3 ** 170 250 50 80 8 5 800 2.2 120 40 A5030Z_ 3 ** 400 550 270 340 8 5 800 2.2 150 30 * For individual “ZA,” “ZB,” and “ZC” surge ratings, see table below. ** Asymmetrical General Notes: • All measurements are made at an ambient temperature of 25 °C. I applies to -40 °C through +85 °C temperature range. PP • I is a repetitive surge rating and is guaranteed for the life of the product. PP • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • V is measured at I DRM DRM. • V is measured at 100 V/µs. S • Special voltage (V and V ) and holding current (I ) requirements are available upon request. S DRM H • Off-state capacitance is measured between Pins 4-3 and Pins 2-3 at 1 MHz with a 2 V bias and is a typical value for “ZA” product. “ZB” and “ZC” capacitance is approximately 10 pF higher. • Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings I I I I I I PP PP PP PP PP TSM 2x10 µs 8x20 µs 10x160 µs 10x560 µs 10x1000 µs 60 Hz di/dt Series Amps Amps Amps Amps Amps Amps Amps/µs A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com 2 - 42 © 2004 Littelfuse LP ® +1 972-580-7777 SIDACtor Data Book and Design Guide Four-port Balanced Three-chip Protector Thermal Considerations Package Symbol Parameter Value Unit SIP T Operating Junction Temperature Range -40 to +150 °C J T Storage Temperature Range -65 to +150 °C S R Thermal Resistance: Junction to Ambient 90 °C/W θJA +I +I t = rise time to peak value r I t = decay time to half value T d I T Peak 100 Value I IS S I IH Waveform = t x t H r d II DRM DRM -V 50 -V +V +V Half Value V V DRM VT V DRM T V S V S 0 t t r d 0 t – Time (µs) -I -I V-I Characteristics t x t Pulse Waveform r d 14 12 2.0 10 1.8 1.6 8 1.4 6 25 ˚C 25 ˚C 1.2 4 1.0 2 0.8 0 0.6 -4 0.4 -6 -40 -20 0 20 40 60 80 100 120 140 160 -8 Case Temperature (T ) – ˚C C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (T ) – ˚C J Normalized V Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature S © 2004 Littelfuse LP 2 - 43 http://www.teccor.com ® SIDACtor Data Book and Design Guide +1 972-580-7777 Percent of V Change – % S I I – Peak Pulse Current – %I PP PP H Ratio of I (T = 25 ˚C) H C Data Sheets