Multiport Balanced SIDACtor Device Multiport Balanced SIDACtor Device This multiport balanced protector is a surface mount alternative to the modified TO-220 1 6 package. It is based on a six-pin surface mount SOIC package and uses Littelfuse’s 2 5 patented “Y” (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A. 3 4 SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters — Symmetrical V V V V C DRM S DRM S O Volts Volts Volt Volts pF Part V I I I I T DRM S T H Number * Pins 1-2, 2-3, 1-3 Pins 4-5, 5-6, 4-6 Volts µAmps mAmps Amps mAmps Pins 3-2, 6-5, 1-2, 4-5 P1556U_ 130 180 130 180 8 5 800 2.2 150 40 P1806U_ 150 210 150 210 8 5 800 2.2 150 40 P2106U_ 170 250 170 250 8 5 800 2.2 150 40 P2356U_ 200 270 200 270 8 5 800 2.2 150 40 P2706U_ 230 300 230 300 8 5 800 2.2 150 30 P3206U_ 270 350 270 350 8 5 800 2.2 150 30 P3406U_ 300 400 300 400 8 5 800 2.2 150 30 P5106U_ 420 600 420 600 8 5 800 2.2 150 30 Electrical Parameters — Asymmetrical V V V V DRM S DRM S Volts Volts Volt Volts Part Pins 1-2, 2-3, 4-5, V I I I I C T DRM S T H O Number * 5-6 Pins 4-6, 1-3 Volts µAmps mAmps Amps mAmps pF A2106U_6 170 250 50 80 3.5 5 800 2.2 120 40 A5030U_6 400 550 270 340 3.5 5 800 2.2 150 30 * For individual “UA”, “UB”, and “UC” surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. I applies to -40 °C through +85 °C temperature range. PP • I is a repetitive surge rating and is guaranteed for the life of the product. PP • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • V is measured at I DRM DRM. • V is measured at 100 V/µs. S • Special voltage (V and V ) and holding current (I ) requirements are available upon request. S DRM H • Off-state capacitance (C ) is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for “UA” product. O “UB” and “UC” capacitance is approximately 10 pF higher. • Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings I I I I I I PP PP PP PP PP TSM 2x10 µs 8x20 µs 10x160 µs 10x560 µs 10x1000 µs 60 Hz di/dt Series Amps Amps Amps Amps Amps Amps Amps/µs A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.littelfuse.com 2 - 26 © 2004 Littelfuse, Inc. ® +1 972-580-7777 SIDACtor Data Book and Design Guide Multiport Balanced SIDACtor Device Thermal Considerations Package Symbol Parameter Value Unit Modified MS-013 T Operating Junction Temperature Range -40 to +125 °C J T Storage Temperature Range -65 to +150 °C S 6 5 R Thermal Resistance: Junction to Ambient 60 °C/W θJA 4 1 2 3 +I +I t = rise time to peak value r I IT T t = decay time to half value d Peak 100 Value I IS S I IH H Waveform = t x t r d II DRM DRM -V 50 -V +V +V Half Value V V VT VDRM DRM T V S V S 0 t t r d 0 t – Time (µs) -I -I V-I Characteristics t x t Pulse Wave-form r d 14 2.0 12 1.8 10 1.6 8 1.4 6 25 ˚C 25 ˚C 1.2 4 1.0 2 0.8 0 0.6 -4 0.4 -6 -40 -20 0 20 40 60 80 100 120 140 160 -8 Case Temperature (T ) – ˚C -40 -20 0 20 40 60 80 100 120 140 160 C Junction Temperature (T ) – ˚C J Normalized V Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature S © 2004 Littelfuse, Inc. 2 - 27 http://www.littelfuse.com ® SIDACtor Data Book and Design Guide +1 972-580-7777 Percent of V Change – % S I – Peak Pulse Current – %I PP PP I H Ratio of I (T = 25 ˚C) H C Data Sheets