100W Single Output Switching Power Supply S-100F series Features : AC input range selectable by switch Protections: Short circuit / Overload / Over voltage Cooling by free air convection 100% full load burn-in test Fixed switching frequency at 83KHz (for 24V only) SPECIFICATION MODEL S-100F-5 S-100F-7.5 S-100F-12 S-100F-15 S-100F-24 S-100F-48 DC VOLTAGE 5V 7.5V 12V 15V 24V 48V RATED CURRENT 20A 13.5A 8.5A 6.7A 4.5A 2.2A CURRENT RANGE 0 ~ 20A 0 ~ 13.5A 0 ~ 8.5A 0 ~ 6.7A 0 ~ 4.5A 0 ~ 2.2A RATED POWER 100W 101W 102W 100.5W 108W 105.6W RIPPLE & NOISE (max.) Note.2 100mVp-p 125mVp-p 125mVp-p 125mVp-p 150mVp-p 150mVp-p OUTPUT VOLTAGE ADJ. RANGE 4.5 ~ 5.5V 6.75 ~ 8.25V 10.8 ~ 13.2V 13.5 ~ 16.5V 21.6 ~ 26.4V 43.2 ~ 52.8V VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 1000ms, 30ms at full load HOLD UP TIME (Typ.) 20ms at full load VOLTAGE RANGE 88 ~ 132VAC/176 ~ 264VAC selected by jumper or switch 248 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 76% 78% 80% 81% 83% 84% INPUT 3.15A/115VAC 1.5A/230VAC AC CURRENT (Typ.) INRUSH CURRENT (Typ.) COLD START 20A/115VAC 40A/230VAC LEAKAGE CURRENT <1mA / 240VAC 105 ~ 150% rated output power OVERLOAD Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION 5.75 ~ 6.75V 8.63 ~ 10.13V 13.8 ~ 16.2V 17.25 ~ 20.25V 27.6 ~ 32.4V 55.2 ~ 64.8V OVER VOLTAGE Protection type : Hiccup mode, recovers automatically after fault condition is removed -10 ~ +60 (Refer to output load derating curve) WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50 VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS CSA60950-1 (for 24V only), UL1012, UL60950-1, TUV EN60950-1, CCC GB4943 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC Compliance to EN55022 (CISPR22) Class B EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A MTBF 314.9K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 199*98*38mm (L*W*H) 0.65Kg; 20pcs/14.2Kg/0.8CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) File Name:S-100F-SPEC 2010-10-18 3.5 3.5 3-M3 100W Single Output Switching Power Supply S-10 0F series Mechanical Specification Case No. 902 Unit:mm 197 1 2 3 4 5 6 7 57.5 120 4.5 199 6.5 190 Terminal Pin No. Assignment Pin No. Assignment Pin No. Assignment 1 AC/L 4,5 DC OUTPUT -V 2 AC/N 6,7 DC OUTPUT +V 3 FG 22 157 Block Diagram fosc : 83KHz 230 115 RECTIFIERS RECTIFIERS EMI +V POWER I/P & & FILTER SWITCHING -V FILTER FILTER DETECTION FG CIRCUIT PWM O.L.P. CONTROL O.V.P. Derating Curve Static Characteristics (24V) Ta=25 32 350 S-100F-12,24 100 28 300 80 24 250 S-100F-5,7.5 20 60 200 16 150 40 12 100 20 8 50 -10 0 10 20 30 40 50 60 (VERTICAL) 80 85 90 95 100 105 110 115 120 125 130 -10 0 45 55 (HORIZONTAL) 160 170 180 190 200 210 220 230 240 250 260 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:S-100F-SPEC 2010-10-18 4-M3 9 8.2 9.5 12 LOAD (%) 18 9 80 OUTPUT VOLTAGE (V) 18 9.5 3.5 3.5 28.5 85.5 7 38 98 OUTPUT RIPPLE (mVp-p)