FTR-K1 SERIES POWER RELAY 1 POLE - 5A Slim Type NY Series n FEATURES l Slim type with 5 mm thickness - Suited for high density mounting l Low power consumption and high sensitivity - Nominal coil power: 120 mW - Operating power: 54 mW l UL, CSA, VDE recognized l Conforms to IEC61010, 61131 l High insulation - Surge voltage: 5,080V - Dielectric strength: 3,000VAC (coil and contacts) l SIL pitch terminals l Plastic sealed type, RTIII l Compatible with solid state I/O module type SN in size and pin (terminal) arrangement l Environmentally friendly cadmium free contact type l RoHS compliant. Please see page 6 for more information n PARTNUMBER INFORMATION NY P - 12 W - K - IE [Example] (a) (b) (*) (c) (d) (e) (*) (f ) (a) Relay type NY : NY-Series (b) Mounting type Nil : PCB board mounting type P : Socket mounting type (c) Coil rated voltage 12 : 4.5.....24 VDC Coil rating table at page 3 (d) Contact design W : Bifurcated contact (e) Enclosure K : Plastic sealed type, RTIII (f) Insulation IE : Complies with IEC standard, IEC61010, 61131 Note: Actual marking omits the hyphen (-) and IE of (*) 1 FTR-K1 SERIES NY SERIES n SPECIFICATION Item NY Contact Data Configuration 1 form A (SPST-NO) Construction Bifurcated Material Gold overlay silver alloy (AgNi + Au) Resistance (initial) Max. 30 mΩ at 6 VDC, 1 A Contact rating 5A, 250VAC / 30VDC Max. carrying current 5A Max. switching voltage 270VAC / 150 VDC Max. switching power 750VA / 90W Max. switching current 5A Min. switching load * 1 mA, 5 VDC 6 Life Mechanical Min. 20 x 10 operations 3 Min. 100 x 10 operations (at 3A, 250VAC, 30VDC resistive) Electrical 3 Min. 50 x 10 operations (at 5A, 250VAC, 30VDC resistive) Coil Data Rated power (at 20 °C) 120 mW Operate power (at 20 °C) 54 mW Operating temperature range -40 °C to +90 °C (no frost) Timing Data Operate (at nominal voltage) Max. 10 ms (without bounce) Release (at nominal voltage) Max. 5 ms (no diode) Insulation Resistance (initial) Min. 1,000MΩ at 500VDC Dielectric strength Open contacts 750VAC, 1min Contacts to coil 3,000VAC, 1min Surge strength Coil to contacts 5,080V / 1.2 x 50µs standard wave Other Misoperation 10 to 55Hz double amplitude 1.5 mm Vibration resistance Endurance 10 to 55Hz double amplitude 5 mm Misoperation Min. 100m/s² (11 ± 1ms) Shock Endurance Min. 1,000m/s² (6 ± 1ms) Weight Approximately 3.5 g Sealing Plastic sealed, RTIII * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES NY SERIES n COIL RATING Rated Coil Must Operate Must Release- Coil Coil Resistance Rated Power Voltage Voltage Voltage Code +/- 10% (Ohm) (mW) (VDC) (VDC) * (VDC) * 4.5 4.5 169 3 0.45 5 5 208 3.35 0.5 6 6 300 4 0.6 120 9 9 675 6 0.9 12 12 1,200 8 1.2 18 18 2,700 12.1 1.8 24 24 4,800 16.1 2.4 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508, UL 1604 Flammability: UL 94-V0 (plastics) 3A (General use) E56140, E199193 5A, 250VAC/30 VDC (resistive) CSA C22.2 No. 14 1/8 HP, 250VAC /125VAC LR 35579 Pilot duty: C300 VDE 0435 part 201 5A, 250VAC, cos φ1, 30K (-40 / 80 °C) 40016933 5A, 30VDC, 0msec, 100K (-40 / 80 °C) Also complies with VDE, IEC 61010, 61131 3 FTR-K1 SERIES NY SERIES n CHARACTERISTIC DATA 4 FTR-K1 SERIES NY SERIES n DIMENSIONS NY type l Schematics l PC board mounting l Dimensions hole layout (BOTTOM VIEW) NYP type l Schematics l PC board mounting l Dimensions hole layout (BOTTOM VIEW) Socket type JL-5N l Dimensions l PC board mounting hole layout (BOTTOM VIEW) 5 FTR-K1 SERIES NY SERIES RoHS Compliance and Lead Free Information 1. General Information l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: maximum 120˚C Soldering: dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1 SERIES NY SERIES Fujitsu Components International Headquarter Offices Japan Europe Fujitsu Component Limited Fujitsu Components Europe B.V. Gotanda-Chuo Building Diamantlaan 25 3-5, Higashigotanda 2-chome, Shinagawa-ku 2132 WV Hoofddorp Tokyo 141, Japan Netherlands Tel: (81-3) 5449-7010 Tel: (31-23) 5560910 Fax: (81-3) 5449-2626 Fax: (31-23) 5560950 Email: promothq@ft.ed.fujitsu.com Email: info@fceu.fujitsu.com Web: www.fcl.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Asia Pacific Fujitsu Components America, Inc. Fujitsu Components Asia Ltd. 250 E. Caribbean Drive 102E Pasir Panjang Road Sunnyvale, CA 94089 U.S.A. #01-01 Citilink Warehouse Complex Tel: (1-408) 745-4900 Singapore 118529 Fax: (1-408) 745-4970 Tel: (65) 6375-8560 Email: components@us.fujitsu.com Fax: (65) 6273-3021 Web: http://us.fujitsu.com/components Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. December 21, 2011 7