TIMING, TEST & MEASUREMENT TSC 3000 Series Hot-swap Chassis Symmetricom’s TSC 3000 series chassis information from each module and provides KEY BENEFITS • uses the Univeral Serial Bus (USB) to enable summary information for remote collection Hot Swapping of All Modules, Chassis the removal and insertion of modules without over an Ethernet connection. Hot-swapping CPU, and Power Supplies removing power or affecting other operating is extended to the power supplies (and • Auto-switching for 5/10 MHz, 1PPS modules. The TSC 3000 Series Hot-swap controlling computer) so that the chassis and IRIG-B (Modulated and DC) chassis provides the perfect vehicle for fault can be serviced without affecting users. • Low Noise Amplifiers for Signal switching and signal distribution to any Distribution number of users. Large systems can be The Hot-swap Chassis can be configured to constructed at once or can evolve with the custom requirements. • Status and Alarm Collection for All addition of distribution modules over time. Input and Output Signals A controlling computer packaged in the Please contact Symmetricom with any • Alarm Reporting over Ethernet 3000 chassis collects status and alarm specific requirements. Interface • Dual Redundant Fans and Power Supplies for High Reliability 3000 Series Hot-swap Chassis OUTPUT MODULES TSC 3000 Series Specifications The TSC 3000’s signal amplifiers provide high quality copies of an input signal for time, frequency and timecode signals. Each amplifier can be inserted into the SWITCHING MODULES chassis and put into service without affecting other modules in the chassis. The TSC 3000 Series hot-swap chassis offers a full set of plug-in modules for Similarly, modules can be removed from the chassis without affecting users switching between redundant inputs and for large-scale signal distribution. connected to other modules. Symmetricom TSC amplifiers are manufactured to Switches for 5 MHz, 10 MHz, 1PPS and IRIG-B switch between two inputs. The the highest specifications: low additive phase noise, high output isolation, low jitter switches can be operated manually or in auto-switch mode where the selection and fast rise time. of input is changed based on a loss-of-signal detection. TSC 3032D / 3032E PULSE DISTRIBUTION AMPLIFIERS COMMON CHARACTERISTICS • Width: 1 Slot • Width: 1 Slot • Connectors • Computer: Control via internal USB bus Input: 1 SMA female • Local control: Locking toggle Output: 8 SMA female • Input/output Impedance: 50Ω • Input level: TTL • Input repetition rate: 1PPS – 1 MPPS (3V) TSC 3091 RF FAULT SENSE SWITCH 1PPS – 1 kPPS (5V) • Connectors • Output level: 3 or 5 V ± .5 V Input: 2 SMA female • Duty cycle limit: 0 – 50% Output: 1 SMA female • Skew: <1 ns • Input level: RF: 1 V RMS nominal (13 dBm) • Jitter: <100 ps • Input frequency: 5 or 10 MHz • Input/output impedance: 50Ω • Output level: 1 V RMS nominal (13 dBm ±1dB) into 50Ω TSC 3036C RF DISTRIBUTION AMPLIFIER TSC 3092 IRIG FAULT SENSE SWITCH • Width: 1 Slot • Connectors • Connectors Input: 2 SMA female Input: 1 SMA female Output: 4 SMA female Output: 6 SMA female • Input level: <6 V P-P • Outputs: 1 – 20 MHz • Output level: Unity gain • Inputs: 1 – 20 MHz • Input level: 0 – 1 V RMS (13 dBm) TSC 3093 TLL FAULT SENSE SWITCH • Gain: 1.0 ± 10% • Connectors • SSB Additive phase noise Input: 2 SMA female Output: 4 SMA female 1Hz -135 dBc 10Hz -145 dBc • Input level 100Hz -155 dBc 1PPS: 2.4-5 V Peak 1kHz -163 dBc DC IRIG: 2.4-5 V Peak 10kHz+ -163 dBc • Output level: TTL: 3 V Peak into 50Ω • Output isolation: >100 dB • Harmonic distortion: <-40 dBc TSC 3094 TLL PPS to ECL PPS SWITCH • Input/output impedance: 50Ω • Connectors Input: 2 SMA female TSC 3059B LOW FREQUENCY DISTRIBUTION AMPLIFIER Output: 4 Differential LEMO (NIMCAMAC) • Width: 1 Slot • Input level: 1PPS: 2.4-5 V Peak • Connectors • Output level: 4 each Differential IOOK ECL Outputs Input: 1 SMA female • Common mode voltage: -1.3 ± .2 V Output: 8 SMA female • Differential voltage: 1.5 Vpp min. 28 Vpp max. • Input/output level: <6 V P-P • Skew: <200 ps • Code format: Any modulated • Jitter: <100 ps • Modulation frequency: 1 – 100 kHz • Modulation ratio: Any • Gain: 1.0 • Input/output impedance: 50Ω SYMMETRICOM, INC. 2300 Orchard Parkway San Jose, California 95131-1017 tel: 408.433.0910 fax: 408.428.7896 info@symmetricom.com ©2006 Symmetricom. Symmetricom and the Symmetricom logo are registered trademarks of Symmetricom, Inc. All specifications subject to www.symmetricom.com change without notice. DS/3000/D/1206/PDF