GNX-800 LOW PROFILE -800 WATTS ONE TO FOUR OUTPUTS - POWER FACTOR CORRECTED 90-264 VAC 40 AMP CAPABILITY ON V2 - 120 AMPS ON V1 FEATURES: Low Profile 2.5" x 5" x 12.92" in Size One to Four outputs Utilizes High Efficiency PWM Topology Meets EN55022 Level A / FCC Class A No Additional Cooling Required up to 50 °C Power Factor Corrected Input (90-264VAC) Remote Sense On V1, V2 Outputs Greater than 150,000 Hrs MTBF Zero Wire Current Share on V1 & V2 Outputs OUTPUT OUTPUT OUTPUT VOLTAGE (VDC) AMPERS (MAX) POWER (WATTS) V1 1.8 to 48 120 800 V2 1.8 to 24 40 200 V3 5 to 24 12/20pk 150 V4 3.3 to 24 10 120 3601 VETERANS HIGHWAY VISIT US ON THE WEB: RONKONKOMA, NEW YORK 11779 http://www.switchpwr.com TEL (631) 981-7231 FAX (631) 981-7266 GNX-800 SERIES 800 WATT COMPACT SIZE * IN PDF FORMAT,PRINT OR ZOOM TO SEE DRAWING Nominal Input Voltage 115-240 VAC, 12A max. Overtemperature Unit shuts down if overheated. Recycle AC to reset. Frequency 47-63 Hz , 400Hz. available. Protection Operational Input 90-264 VAC Leakage Current 1.5mA max at 240Vac. Voltage Range Power Factor 0.99 Typical at Full Load. Meets EN 61000-3-2. Current Limiting All outputs short circuit protected with Shutdown Inrush Current Less than 4 msec. 30 amperes @ 115 VAC protection. Recycle AC to reset. or 60 amperes @ 264 VAC. Peak Output Current Peak current can be delivered for a maximum Brownout Protection: Holds Regulation to 85 Vac. period of 30 seconds. Fusing 15 Ampere, 250 VAC, Internal ceramic body fuse. Paralleling Two or more supplies can be operated in parallel and will share V1/V2 current to within 10% of each Hold up time 20msec minimum after loss of AC Input at full load other. and any input Remote Sense Compensates for up to 0.5V total distribution voltage Efficiency 75% typical drop on the V1 & V2 outputs. Turn on time 1 sec max. from power up. All output voltages come up within 10msec of each other. INH Open to Run, Contact closure to return , turns off all outputs. Line and Load ±2% over AC input range and Regulation 0 to 100% load change. FAIL Signal Normal logic '1' TTL signal which goes low whenever the V1 , V2 outputs fail, an overtemperature condition, Minimum Load 5% minimum load required on V1 for V2 to regulate to full load. an over voltage shut down, or an AC input failure No minimum load required on V2-V4. (5msec warning before outputs go out of regulation). Ripple & Noise Through 20MHz 1% max. or 100mv whichever is greater for all outputs, peak to peak, with coaxial probe Cooling Integral fans provide 50cfm of air flow. and 0.1uF/10uF capacitors at the connector. Operating Temperature -40°C to 50°C operating temperature with full load. Transient Response Output maximum excursion of ± 5% for 50% load step. Recovery less than 500 μsec. Stability All outputs 0.1% for 8 hrs. after 30 minute warm-up. Overshoot/Undershoot No turn-on or turn-off overshoot. Humidity Up to 95% non-condensing. Output Isolation Isolated from chassis ground, 50Vdc. Storage Temperature -40°C to 85°C. Input/Output Isolation 2200 VDC from input to both chassis/outputs. Size 5" x 2.5" x 12.96" Weight: 8 lbs. SELV construction. EMC Meets EN55022 Level A / FCC Class A conducted. Reverse Voltage Protected against reverse voltage to supply current rating. Safety UL 1950, CSA C22.2 No. 950, EN60950. Overvoltage Shutdown at 130% of nominal Vout V1, V2, V3. Protection V4 failsafe design. Recycle input power to reset. SERIES BREAKDOWN: GNX-800X1-P REV: E where X1= S for Single output, D for Dual output, T for Triple output or Q for Quad output