Elite.Parts Manufacturers S STMICROELECTRONICS M68AF511AL70MC6T
About product Datasheet FAQ

STMICROELECTRONICS M68AF511AL70MC6T

Description

IC SRAM 4MBIT 3V ASYNC 32-SOIC

Part Number

M68AF511AL70MC6T

Price

Request Quote

Manufacturer

STMICROELECTRONICS

Lead Time

Request Quote

Category

PRODUCTS - M

Datasheet

pdf file

4263277_1.pdf

129 KiB

Extracted Text

M68AF511A 4 Mbit (512K x8), 5V Asynchronous SRAM FEATURES SUMMARY SUPPLY VOLTAGE: 4.5 to 5.5V Figure 1. Packages 512K x 8 bits SRAM with OUTPUT ENABLE EQUAL CYCLE and ACCESS TIMES: 55ns LOW STANDBY CURRENT 32 LOW V DATA RETENTION: 2V CC TRI-STATE COMMON I/O 1 LOW ACTIVE and STANDBY POWER TSOP32 Type II (NC) SO32 (MC) October 2002 1/18 M68AF511A TABLE OF CONTENTS SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table 1. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 3. TSOP and SO Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Figure 4. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table 2. Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table 3. Operating and AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 5. AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 6. AC Measurement Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Table 4. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 5. DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 6. Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 7. Address Controlled, Read Mode AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 8. Chip Enable or Output Enable Controlled, Read Mode AC Waveforms. . . . . . . . . . . . . . . 9 Table 7. Read and Standby Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Write Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 10. Write Enable Controlled, Write AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 11. Chip Enable Controlled, Write AC Waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 8. Write Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 9. Low V Data Retention Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 CC PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 TSOP 32 Type II - 32 lead Plastic Thin Small Outline Type II, Package Outline . . . . . . . . . . . . . . 14 TSOP 32 Type II - 32 lead Plastic Thin Small Outline Type II, Package Mechanical Data . . . . . . . 14 SO32 - 32 lead Plastic Small Outline, Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SO32 - 32 lead Plastic Small Outline, Package Mechanical Data. . . . . . . . . . . . . . . . . . . . . . . . . . 15 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 12. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 13. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 2/18 M68AF511A SUMMARY DESCRIPTION The M68AF511A is a 4 Mbit (4,194,304 bit) CMOS This device has an automatic power-down feature, SRAM, organized as 524,288 words by 8 bits. The reducing the power consumption by over 99% device features fully static operation requiring no when deselected. external clocks or timing strobes, with equal ad- The M68AF511A is available in a 32 lead TSOP dress access and cycle times. It requires a single Type II and 32 lead SO packages. 4.5 to 5.5V supply. Figure 2. Logic Diagram Table 1. Signal Names A0-A18 Address Inputs DQ0-DQ7 Data Input/Output V CC E Chip Enable G Output Enable 19 8 W Write Enable A0-A18 DQ0-DQ7 V Supply Voltage CC W V Ground SS M68AF511A E G V SS AI03948C 3/18 M68AF511A Figure 3. TSOP and SO Connections A17 1 32 V CC A16 A15 A14 A18 A12 W A7 A13 A6 A8 A5 A9 A4 8 25 A11 M68AF511A A3 9 24 G A2 A10 A1 E A0 DQ7 DQ0 DQ6 DQ1 DQ5 DQ2 DQ4 V 16 17 DQ3 SS AI03949C 4/18 M68AF511A Figure 4. Block Diagram A18 V CC V SS ROW MEMORY DECODER ARRAY A8 DQ7 I/O CIRCUITS COLUMN DECODER DQ0 A0 A7 E W G AI05916 MAXIMUM RATING Stressing the device above the rating listed in the plied. Exposure to Absolute Maximum Rating con- Absolute Maximum Ratings table may cause per- ditions for periods greater than 1 sec may affect manent damage to the device. These are stress device reliability. Refer also to the STMicroelec- ratings only and operation of the device at these or tronics SURE Program and other relevant quality any other conditions above those indicated in the documents. Operating sections of this specification is not im- Table 2. Absolute Maximum Ratings Symbol Parameter Value Unit (1) Output Current 20 mA I O T Ambient Operating Temperature –55 to 125 °C A T Storage Temperature –65 to 150 °C STG V Supply Voltage –0.5 to 6.5 V CC (2) –0.5 to V +0.5 V Input or Output Voltage V CC IO P Power Dissipation 1 W D Note: 1. One output at a time, not to exceed 1 second duration. 2. Up to a maximum operating V of 6.0V only. CC 5/18 M68AF511A DC AND AC PARAMETERS This section summarizes the operating and mea- ment Conditions listed in the relevant tables. De- surement conditions, as well as the DC and AC signers should check that the operating conditions characteristics of the device. The parameters in in their projects match the measurement condi- the following DC and AC Characteristic tables are tions when using the quoted parameters. derived from tests performed under the Measure- Table 3. Operating and AC Measurement Conditions Parameter M68AF511A V Supply Voltage 4.5 to 5.5V CC Range 1: Commercial 0 to 70°C Ambient Operating Temperature Range 6: Industrial –40 to 85°C Load Capacitance (C ) 100pF L Output Circuit Protection Resistance (R ) 3.0kΩ 1 Load Resistance (R ) 3.1kΩ 2 Input Rise and Fall Times 1ns/V Input Pulse Voltages 0 to V CC Input and Output Timing Ref. Voltages V /2 CC Output Transition Timing Ref. Voltages V = 0.3V ; V = 0.7V RL CC RH CC Figure 5. AC Measurement I/O Waveform Figure 6. AC Measurement Load Circuit V CC I/O Timing Reference Voltage R 1 V CC V /2 CC DEVICE UNDER OUT 0V TEST C L Output Transition Timing Reference Voltage R 2 V CC 0.7V CC 0.3V CC 0V AI05910 C includes probe and 1 TTLcapacitance L AI05832 6/18 M68AF511A Table 4. Capacitance Test (1,2) Symbol Min Max Unit Parameter Condition C Input Capacitance on all pins (except DQ) V = 0V 6pF IN IN Output Capacitance V = 0V 8pF C OUT OUT Note: 1. Sampled only, not 100% tested. 2. At T = 25°C, f = 1MHz, V = 5.0V. A CC Table 5. DC Characteristics Symbol Parameter Test Condition Min Typ Max Unit V = 5.5V , CC (1,2) Operating Supply Current 55 mA I CC1 f = 1/t , I = 0mA AVAV OUT V = 5.5V, CC (3) I Operating Supply Current 5mA CC2 f = 1MHz, I = 0mA OUT I 0V ≤ V ≤ V Input Leakage Current –1 1 μA LI IN CC (4) Output Leakage Current 0V ≤ V ≤ V –1 1 μA I OUT CC LO V = 5.5V, E ≥ V – 0.2V, CC CC Standby Supply Current CMOS 510 μA I SB f= 0 V V + 0.3 Input High Voltage 2.2 V IH CC V Input Low Voltage –0.3 0.8 V IL V I = –1.0mA Output High Voltage 2.4 V OH OH V Output Low Voltage I = 2.1mA 0.4 V OL OL Note: 1. Average AC current, cycling at t minimum. AVAV 2. E = V , V = V or V . IL IN IH IL 3. E ≤ 0.2V, V ≤ 0.2V or V ≥ V – 0.2V. IN IN CC 4. Output disable. 7/18 M68AF511A OPERATION The M68AF511A has a Chip Enable power down cles to be achieved with the common I/O data bus. feature which invokes an automatic standby mode Operational modes are determined by device con- whenever Chip Enable is de-asserted (E = High). trol inputs W and E as summarized in the Operat- An Output Enable (G) signal provides a high ing Modes table (Table 6). speed tri-state control, allowing fast read/write cy- Table 6. Operating Modes Operation E W G DQ0-DQ7 Power Output disabled V XV Hi-Z Active (I ) IL IH CC V V V Active (I ) Read IL IH IL Data Output CC Write V V X Data Input Active (I ) IL IL CC V Standby (I ) Deselect X X Hi-Z IH SB Note: X = V or V . IH IL Read Mode The M68AF511A is in the Read mode whenever stable address, providing G is Low and E is Low. Write Enable (W) is High with Output Enable (G) If Chip Enable or Output Enable access times are Low, and Chip Enable (E) is asserted. This pro- not met, data access will be measured from the vides access to data from eight of the 4,194,304 limiting parameter (t or t ) rather than the ELQV GLQV locations in the static memory array, specified by address. Data out may be indeterminate at t ELQX the 19 address inputs. Valid data will be available and t , but data lines will always be valid at GLQX at the eight output pins within t after the last t . AVQV AVQV Figure 7. Address Controlled, Read Mode AC Waveforms tAVAV A0-A18 VALID tAVQV tAXQX DQ0-DQ7 DATA VALID AI03034 Note: E = Low, G = Low, W = High. 8/18 M68AF511A Figure 8. Chip Enable or Output Enable Controlled, Read Mode AC Waveforms. tAVAV A0-A18 VALID tAVQV tAXQX tELQV tEHQZ E tELQX tGLQV tGHQZ G tGLQX DQ0-DQ7 VALID AI05912 Note: Write Enable (W) = High. Figure 9. Chip Enable Controlled, Standby Mode AC Waveforms E tPU tPD I CC 50% I SB AI03036 9/18 M68AF511A Table 7. Read and Standby Mode AC Characteristics M68AF511A Symbol Parameter Unit 55 70 t Read Cycle Time Min 55 70 ns AVAV t Address Valid to Output Valid Max 55 70 ns AVQV (1) t Data hold from Address change Min 5 5 ns AXQX (2,3) t Chip Enable High to Output Hi-Z Max 20 25 ns EHQZ t Chip Enable Low to Output Valid Max 55 70 ns ELQV (1) Chip Enable Low to Output Transition Min 5 5 ns t ELQX (2,3) Output Enable High to Output Hi-Z Max 20 25 ns t GHQZ t Output Enable Low to Output Valid Max 25 35 ns GLQV (1) t Output Enable Low to Output Transition Min 5 5 ns GLQX (4) t Chip Enable High to Power Down Max 0 0 ns PD (4) Chip Enable Low to Power Up Min 55 70 ns t PU Note: 1. Test conditions assume transition timig reference level = 0.3V or 0.7V . CC CC 2. At any given temperature and voltage condition, t is less than t and t is less than t for any given device. EHQZ ELQX GHQZ GLQX 3. These parameters are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 4. Tested initially and after any design or process changes that may affect these parameters 10/18 M68AF511A Write Mode The M68AF511A is in the Write mode whenever The Write cycle can be terminated by the earlier the W and E pins are Low. Either the Chip Enable rising edge of E, or W. input (E) or the Write Enable input (W) must be de- if the Output is enabled (E = Low and G = Low), asserted during Address transitions for subse- then W will return the outputs to high impedance quent write cycles. Write begins with the concur- within t of its falling edge. Care must be taken WLQZ rence of Chip Enable being active with W low. to avoid bus contention in this type of operation. Therefore, address setup time is referenced to Data input must be valid for t before the ris- DVWH Write Enable and Chip Enable as t and t AVWL AVEH ing edge of Write Enable, or for t before the DVEH respectively, and is determined by the latter occur- rising edge of E, whichever occurs first, and re- ring edge. main valid for t or t . WHDX EHDX Figure 10. Write Enable Controlled, Write AC Waveforms tAVAV A0-A18 VALID tAVWH tELWH tWHAX E tWLWH tAVWL W tWLQZ tWHQX tWHDX (1) (1) DQ0-DQ7 DATA DATA INPUT DATA tDVWH AI05913 Note: 1. During this period DQ0-DQ7 are in output state and input signal should not be applied. 11/18 M68AF511A Figure 11. Chip Enable Controlled, Write AC Waveforms tAVAV A0-A18 VALID tAVEH tAVEL tELEH tEHAX E tWLEH W tEHDX DQ0-DQ7 DATA INPUT tDVEH AI05914 Table 8. Write Mode AC Characteristics M68AF511A Symbol Parameter Unit 55 70 t Write Cycle Time Min 55 70 ns AVAV t Address Valid to Chip Enable High Min 45 60 ns AVEH t Address Valid to Chip Enable Low Min 0 0 ns AVEL t Address Valid to Write Enable High Min 45 60 ns AVWH t Address Valid to Write Enable Low Min 0 0 ns AVWL t Input Valid to Chip Enable High Min 25 30 ns DVEH t Input Valid to Write Enable High Min 25 30 ns DVWH t Chip Enable High to Address Transition Min 0 0 ns EHAX t Chip Enable High to Input Transition Min 0 0 ns EHDX t Chip Enable Low to Chip Enable High Min 45 60 ns ELEH t Chip Enable Low to Write Enable High Min 45 60 ns ELWH t Write Enable High to Address Transition Min 0 0 ns WHAX t Write Enable High to Input Transition Min 0 0 ns WHDX (1) t Write Enable High to Output Transition Min 5 5 ns WHQX t Write Enable Low to Chip Enable High Min 45 60 ns WLEH (1,2) Write Enable Low to Output Hi-Z Max 20 25 ns t WLQZ t Write Enable Low to Write Enable High Min 45 60 ns WLWH Note: 1. These parameters are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 2. At any given temperature and voltage condition, t is less than t for any given device. WLQZ WHQX 12/18 M68AF511A Figure 12. Low V Data Retention AC Waveforms. CC DATA RETENTION MODE 5.5V V 4.5V CC V > 2.0V DR tCDR tR E ≥ V – 0.2V DR E 2.2V AI05915 Table 9. Low V Data Retention Characteristics CC Symbol Parameter Test Condition Min Typ Max Unit (1) (3) Supply Current (Data Retention) 4.5 9 μA I V = 2V, E ≥ V – 0.2V, f = 0 CCDR CC CC Chip Deselected to Data (1,2) t 0ns CDR Retention Time (2) Operation Recovery Time t ns t AVAV R (2) Supply Voltage (Data Retention) E ≥ V – 0.2V, f = 0 2V V CC DR Note: 1. All other Inputs at V ≥ V –0.2V or V ≤ 0.2V. IH CC IL 2. Tested initially and after any design or process that may affect these parameteres. t is Read cycle time. AVAV 3. No input may exceed V +0.2V. CC 13/18 M68AF511A PACKAGE MECHANICAL Figure 13. TSOP 32 Type II - 32 lead Plastic Thin Small Outline Type II, Package Outline D N E1 E 1 N/2 b e A2 A C α A1 L CP TSOP-e Note: Drawing is not to scale. Table 10. TSOP 32 Type II - 32 lead Plastic Thin Small Outline Type II, Package Mechanical Data millimeters inches Symbol Typ Min Max Typ Min Max A 1.20 0.047 A1 0.05 0.15 0.002 0.006 A2 0.95 1.05 0.037 0.041 b 0.30 0.52 0.012 0.020 C 0.12 0.21 0.005 0.008 CP 0.10 0.004 D 20.82 21.08 0.820 0.830 e 1.27 – – 0.050 – – E 11.56 11.96 0.455 0.471 E1 10.03 10.29 0.395 0.405 L 0.40 0.60 0.016 0.024 α 0° 5° 0° 5° N32 32 14/18 M68AF511A Figure 14. SO32 - 32 lead Plastic Small Outline, Package Outline D 16 1 E E1 17 32 A2 A C CP A1 B e L1 L SO-C Note: Drawing is not to scale. Table 11. SO32 - 32 lead Plastic Small Outline, Package Mechanical Data millimeters inches Symbol Typ Min Max Typ Min Max A 3.00 0.118 A1 0.10 0.004 A2 2.57 2.82 0.101 0.111 B 0.36 0.51 0.014 0.020 C 0.15 0.30 0.006 0.012 D 20.14 20.75 0.793 0.817 E 11.18 11.43 0.440 0.450 E1 13.87 14.38 0.546 0.566 e 1.27 – – 0.050 – – L 0.58 0.99 0.023 0.039 L1 1.19 1.60 0.047 0.063 CP 0.10 0.004 15/18 M68AF511A PART NUMBERING Table 12. Ordering Information Scheme Example: M68AF511 A L 55 NC 1 T Device Type M68 Mode A = Asynchronous Operating Voltage F = 4.5V to 5.5V Array Organization 511 = 4 Mbit (512K x8) Option 1 A = 1 Chip Enable Option 2 L = L-Die M = M-Die Speed Class 55 = 55ns 70 = 70 ns Package NC = TSOP32 Type II MC = SO32 Operative Temperature 1 = 0 to 70 °C 6 = –40 to 85 °C Shipping T = Tape & Reel Packing For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the STMicroelectronics Sales Office nearest to you. 16/18 M68AF511A REVISION HISTORY Table 13. Document Revision History Date Version Revision Details July 2001 -01 First Issue SO32 Package added 08-Aug-2001 -02 55ns Speed class introduced Industrial Temperature Range added (Range 6) 27-Sep-2001 -03 Typing error, Table 4, Note 2 18-Oct-2001 -04 SO32 Package Mechanical and Data added 29-Nov-2001 -05 Note Removed from Ordering Information Scheme PDIP32 package added 08-Jan-2002 -06 Document fully revised t , t changed in Read and Standby Mode AC Characteristics Table (Table 7) ELQX AXQX 08-Feb-2002 -07 t , t , t changed in Write Mode AC Characteristics Table (Table 8) DVEH DVWH WLWH PDIP32 package removed Block Diagram clarified (Figure 4) Absolute Maximum Ratings table clarified (Table 2) 25-Feb-2002 -08 Operating and AC Measurement Conditions table and figure clarified (Table 3, Figure 6) DC Characteristics table clarified (Table 5) Read and Standby Mode AC Characteristics table clarified (Table 7) Write Mode AC Characteristics table clarified (Table 8) Operating and AC Measurement Conditions table clarified (Table 3) 03-Mar-2002 -09 I Test Condition clarified (Table 9) CCDR Read and Standby Mode AC Characteristics clarified (Table 7) 25-Mar-2002 -10 Low V Data Retention Characteristics clarified (Table 9) CC Read and Standby Mode AC Characteristics (Table 7): t and t clarified 18-Apr-2002 -11 PD PU DC Characteristics Table clarified (Table 5) 26-Apr-2002 -12 Write Mode AC Characteristics Table clarified (Table 8) 17-May-2002 -13 I and I values clarified SB CCDR Revision numbering modified: a minor revision will be indicated by incrementing the digit after the dot, and a major revision, by incrementing the digit before the dot (revision 02-Oct-2002 13.1 version 013 equals 13.0). New part number added. 09-Oct-2002 13.2 Datasheet number simplified. 17/18 M68AF511A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners. © 2002 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com 18/18

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the M68AF511AL70MC6T have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

IC SRL EEPROM 256KBIT 5.5V 8SOIC

Serial EEPROM IC

Parallel EEPROM IC

IC SRL EEPROM 2KBIT 5.5V 8-PDIP

product

STMICROELECTRONICS M4T28-BR12SH1 Battery - TimeKeeper SnapHat (Battery & Crystal)

product

IC GENERATOR 9BIT PARITY 14-SOIC