TCM1000, Power Factor Corrected Single Output, Hot Swap FEATURES: Diode isolated output for hot swap “Zero wire” slope program current sharing High power density 6.5 Watt/cu. in. Industry standard DIN connector 0.99 typical power factor Dc power good and ac power fail signals True remote inhibit Monotonic turn-on and turn-off Extended temperature operation High efficiency 87% typical (48 V units) Operating temperature range -20°C to +60°C SPECIFICATIONS: INPUT Ac Input: 180-264 Vac, 47-63 Hz internally fused 10 A. output voltage rating. (internal OR-ing diode.) Power Factor: 0.99 typical at full load. Meets EN61000-3.2 Class A. ENVIRONMENTAL Inrush: Limited by thermistor, 40 A maximum (8ms), cold start. Thermal Protection: Shuts down power supply if overheated. Hold Up Time: 20 ms minimum after removal of ac power at Automatic recovery. full load. Temperature Range: -20° to +50° C, full power, de-rate to 66% Efficiency: 87% typical @ full load. maximum power @ 71° C. Ac Power Fail: Provides TTL “0” 5 ms before output voltage Safety Agencies: Approved to UL1950; CSA 22.2 #950; IEC 950 goes out of regulation band upon loss of ac power. and TUV EN60950, Class 1 SELV, CE 73/23/EEC//93/68/EEC OUTPUT (low voltage directive). Adjustability: User adjustable ±5% minimum. Conducted RFI: Meets FCC Part 15, Class A; EN55022 Class B. Output Isolation: Isolated from ground 100 Vdc. Line Regulation: ±0.2% Load Regulation: ±2% (Slope Program) from 0 to 100% load Cooling: Self-cooled by internal ball-bearing fan. changes. Turn On Delay: 1 second typical. OPTIONS Ripple & Noise: 0.5% p-p, measured at 20 MHz bandwidth. Option “R” - Rack Mount Panel: special panel that is required Temperature Coefficient: 0.02% per degree C. for rack mounting. Stability: 0.1% over 8 hours, under constant line, load and ambient. AC INPUT(180-264 VAC Continuous Range) Transient Response: Output voltage returns to within 1% in less LOCATION 230 VAC CONNECTOR than 500 µs for a 50% load change. Peak transient does not exceed 3%. Z1 32 Lr ine Eurocard connecto Overload Protection: Electronic current limit, 120% maximum. D2 30 L2 ine male DIN 41 61 Overvoltage Protection: Protects load against power supply Zd 28 SH afety Groun level 1 - type induced overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. Requires ac input to be DC OUTPUT cycled to reset. FUNCTION LOCATION NOTES CONNECTOR Remote Inhibit: Contact closure or TTL “0” turns off output. Dc Power Good: Provides a TTL “0” open collector when output O8 utput VoltageZy 12 D14 Z16 D1(e +) to Polarit Eurocard connector-mal is above 90% of nominal. Maximum pull-up voltage 30 Vdc; Zy 4 D6 Z8 D10(H -) to Polarit DIN 41 612 Level 1-type maximum sink current, 10 mA. Redundancy: Built-in OR-ing diode, slope program current STATUS AND CONTROL sharing, and DIN blade connector provide “hot swap” and “N+1” FUNCTION LOCATION NOTES CONNECTOR capabilities. Current sharing remains within 10% of the unit’s full D0 c Power GoodZo 2Rr eference t Eurocard connecto output rating given 0.2% initial accuracy in the output voltage setting. A2 c Power FailDn 2 c2 ommo male DIN 41 61 Current Sharing: As calibrated at factory, modules will share I4 nhibitZH 2 level 1-type current within 10% of full rated load. Reverse Voltage: Protected against reverse voltage up to twice Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 94 TCM1000, Power Factor Corrected Single Output, Hot Swap Commercial Model Power Out Output No. Output Current Total Regulation T0 CM-1000-24 11 00 2A 4V 4% 1.6 ±2 T0 CM-1000-28 11 00 2A 8V 3% 5.7 ±2 T0 CM-1000-48 11 00 4A 8V 2% 0.8 ±2 TCM1000 MECHANICAL SPECIFICATIONS: Dimensions: Inches Millimeters Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 95