SPH-1200, Power Factor Corrected Single Output, Hot Swap FEATURES: Diode isolated output for hot swap “Zero wire” slope program current sharing for redundancy High power density: 5 W/cu. in. Industry standard DIN connector Universal ac input 0.99 typical power factor Dc power good and ac power fail signals True remote inhibit Monotonic turn-on and turn-off The SPH-1200 series provides low cost, highly reliable, N+1 redundant hot swap power for critical applications. SPECIFICATIONS: INPUT Ac Input: 105-264 Vac continuous range, 47 to 63 Hz. Internally Status Indicators: Green LED on the front panel indicates fused for 20 A. normal operation (ACPF high and DCPG low) Power Factor: 0.99 typical at full load. Meets EN61000-3-2 Class A. ENVIRONMENTAL Inrush: Cold start ac current is less than 75 A at 115 Vac and Thermal Protection: Shuts down power supply if overheated. 150 A at 230 Vac for 8 ms typical. Limited by thermistor. Automatic recovery. Holdup Time: 16 ms minimum after removal of power at full Temperature Range: 0° to 50°C at full ratings. load. Safety Agencies: Approved to UL1950; CSA 22.2 #950; IEC 950 Efficiency: 80% minimum and TÜV EN60950, Class 1 SELV, CE 73/23/EEC//93/68/EEC Ac Power Fail: Provides TTL “0” 5 ms before output voltage (low voltage directive). goes out of regulation band upon loss of ac power. Conducted RFI: Meets FCC Part 15, Class A; EN55022 Class B. Brownout Protection: Holds regulation to 85 Vac for 30 Cooling: Self-cooled by internal ball-bearing fan. seconds maximum. OUTPUT OPTIONS Adjustability: User adjustable ±5% minimum. Option “R”, Rack Mount Panel: Special panel is required for Line Regulation: ±0.2% rack mounting. Load Regulation: ±2% (Slope Program) from 0 to 100% load change. Turn On Delay: 1 second typical AC INPUT (105-264 VAC Continuous Range) Output Rise Time: (from 10% to 90%) 20 ms typical. LOCATION 115 VAC 230 VAC CONNECTOR Ripple & Noise: Less than 1% p-p, measured at 20 MHz Ze 32 L1 in Lw ine See Belo bandwidth. Temperature Coefficient: 0.02% per degree C. Dl 30 N2 eutra Line Stability: 0.1% over 8 hours after 30 minutes warm-up. Zd 28 Sd afety Groun Safety Groun Transient Response: Output voltage returns to within 1% in less than 500 µs for a 50% load change. Peak transient does not exceed 3%. DC OUTPUT Overload Protection: Electronic current limit, 120% maximum. FUNCTION LOCATION NOTES CONNECTOR Overvoltage Protection: Protects load against power supply induced overvoltage. Trip point is factory set so that output O8 utput VoltageZy 12 D14 Z16 D1(e +) to Polarit Eurocard connector-mal voltage cannot exceed 136% of nominal. Requires ac input to be Zy 4 D6 Z8 D10(H -) to Polarit DIN 41 612 Level 1-type cycled to reset. Remote Inhibit: Contact closure or a TTL level “0” turns off dc output. STATUS AND CONTROL Dc Power Good: Provides a TTL “0” open collector when output FUNCTION LOCATION NOTES CONNECTOR is above 90% of nominal. Maximum pull-up voltage 30 Vdc; D0 c Power GoodZo 2 Re eference t See Abov maximum sink current, 10 mA. Redundancy: Built-in OR-ing diode, slope program current A2 c Power FailDn 2 commo sharing, and DIN blade connector provide “hot swap” and “N+1” I4 nhibit Z2 capabilities. Current sharing remains within 10% of the unit’s full output rating given 0.2% initial accuracy in the output voltage setting. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 96 SPH-1200, Power Factor Corrected Single Output, Hot Swap Commercial Model Power Out Output No. Output Current Total Regulation S0 PH-1200-24 11 20 2A 4V 5% 0 ±2 S0 PH-1200-28 11 20 2A 8V 4% 2 ±2 S0 PH-1200-48 11 20 4A 8V 2% 5 ±2 SPH-1200 MECHANICAL SPECIFICATIONS: Dimensions: Inches Millimeters Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 97