RSC350 Commercial/RSM350 Medical 350 Watt Multiple Output FEATURES:  Automatic line range selection  Fully regulated and floating outputs  Modular output configurations  FCC/CISPR 11, 22  Commercial Approved to UL1950, CSA 22.2 No. 234L6, IEC2950, EN60950  Medical Approved to UL2601-1, IEC601 and CSA 601.1  “Smart Load” feature eliminates minimum load requirements  2-year warranty  marked to LVD SPECIFICATIONS: Ac Input Voltage Adjustment 90-132 and 180-264 Vac. 50/60 Hz single phase Built-in potentiometers adjust outputs minmum of ±5%. Input Current Reverse Voltage Protection 9/4.5 A All outputs protected against inadvertent application of reverse voltage up to 1 times rated current of the reversed output. Hold-Up Time EMI/EMC Compliance 20 ms minimum from loss of ac input at full load, nominal line (115 Vac). Output Power All models include built-in EMI filtering to meet the following emissions requirements: 350 W with cover fan option (390 W) peak). EMI SPECIFICATION COMPLIANCE LEVEL Overload Protection Conducted Emissions EN55022 Class B; FCC Class B Standard on all outputs, recovery automatic. Static Discharge EN61000-4.2, 6 kV contact 8 kV air Overvoltage Protection RF Field Susceptibility EN61000-4.3, 3 V/meter Standard on all outputs within ranges below: OUTPUT OVP SETTING V ADJ. RANGE Fast Transients/Bursts EN610004-4, 2 kV. 5 kHz 5 V 5.6-6.8 V 4.6-5.5 V Surge Susceptibility EN61000-4-5, 1kV diff., 2 kV com 12 V & 15 V 18-22 V 11.5-15.3 V Commercial Leakage Current 24 V & 28 V 29-35 V 22.0-30.0 V 100 µA Efficiency Commercial Safety 74% minimum at full load; nominal input voltage. Approval to UL1950 (no D3 deviations). CSA 22.2 No. 234L6. Turn-on Time IEC950 and EN60950. Less than 2 seconds. Medical Leakage Current Input Protection 80 µA Internal ac fuse provided. Designed to blow only if a catastrophic Medical Safety failure occurs in the unit-fuse does not blow on overload or short Approved to UL2601-1, IEC601, CSA601.1 for patient vicinity circuit. (non-invasive applications. Consult factory for approval status. Inrush Current Outputs are intended for Protectively Earthed Signal Output and 60 A minimum Intermediate Circuits only. Temperture Coefficient Outputs are not acceptable for patient connection without additional isolation. The creepage distance between primary 0.03%/°C typical on all units and ground is 4 mm minimum, 8 mm between primary and Environmental secondary circuits. Designed for 0 to 50°C operation at full rated output power; Vibration derate output current and total output power by 2.5% per °C above 50°C. See Environmental and Packaging Specifications Designed to meet requirements of MIL-STD 810E. Method 514.4 Category 1. This test consists of random vibration at 0.015g/Hz on next page for additonal informaton. from 5 to 50 Hz declining linearly to 0.15 g2/Hz in each axis for Power Fail one hour. Shock Designed to meet MIL-STD 810E. Method A TTL signal goes low upon failure. 6mS min. before output drops 5%. 516.4. Unpackaged units shall meet the bench handling require- Output Noise ments of procedures V1 for four drops per face. 0.5% rms. 1% pk-pk measured directly across output terminals. Transient Response Main output- 500 µsec typical response time for return to within 0.5% of final value for a 50% boad step change. Di/Dt<0.2/µsec. Maximum voltage deivation is 3.5% Remote Sense Standard on main output; will compensate for 0.5 V of cabling losses. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 78 RSC350 Commercial/RSM350 Medical 350 Watt Multiple Output Commercial Medical Main Aux 1 Aux 2 Aux 3 Model Model RSC350BBB RSM350BBB5A V @ 40 A1A 2 V @ 121A 2 V @ 4 12 V @ 4 RSC350DBB RSM350DBB5A V @ 40 A2A 4 V @ 61A 2 V @ 4 12 V @ 4 RSC350DAC RSM350DAC5A V @ 40 A2A 4 V @ 65A V @ 4 15 V @ 4 RSC350BAD RSM350BAD5A V @ 40 A1A 2 V @ 125A V @ 4 24 V @ 2.5 RSC350BAB RSM350BAB5A V @ 40 A1A 2 V @ 125A V @ 4 12 V @ 4 RSC352BAB RSM352BAB2A 4 V @ 8 A1A 2 V @ 125A V @ 4 12 V @ 4 RSC352BAD RSM352BAD2A 4 V @ 8 A1A 2 V @ 125A V @ 4 24 V @ 2.5 RSC352BBB RSM352BBB2A 4 V @ 8 A1A 2 V @ 121A 2 V @ 4 12 V @ 4 RSC352DAC RSM352DAC2A 4 V @ 8 A2A 4 V @ 65A V @ 4 15 V @ 4 RSC352DBB RSM352DBB2A 4 V @ 8 A2A 4 V @ 61A 2 V @ 4 12 V @ 4 Output configurations: "A" auxiliary output adjusts from 4.7 to 5.3Vdc. Available on AUX 2 only "B" auxiliary output adjusts from 11.5 to 15.5Vdc. "C" same as "B" but factory set at 15Vdc. "D" auxiliary output adjusts from 23 to 29Vdc. Available on AUX 1 and 3 RSC35x/RSM35x MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification TC emperature (A)0C to 50º -40 to +85º HH umidity (A)0H to 95% R 0 to 95% R A. Units should be allowed to warm up/operate under non-condensing conditions before Sg hock (B) 20 40 g pk pk application of power. Derated output current and toal output power by 2.5% per ºC above 50ºC. B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 orthogonal axes. At ltitude-t 500 to 10,000 f -500 to 40,000 f Tested for 10 min./axis operating and 1 hr./axis non-operating. 2 2 C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, total 6 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz rms rms shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 79