RMX-350, Multiple Output Power Factor Correction, Hot Swap FEATURES: • Diode isolated outputs for hot swap “Zero wire” slope program current sharing for redundancy Self-aligning connector with solid metal machined contacts Universal ac input 0.99 typical power factor Dual converter design eliminates interaction between logic and auxiliary outputs Low ripple and noise on all outputs Dc power good and ac power fail signals True remote inhibit Monotonic turn-on and turn-off SPECIFICATIONS: INPUT Ac Input: 90-264 Vac continuous range, 47 to 63 Hz. Internally Reverse Voltage: Protected against reverse voltage up to fused for 7A. supply current rating. Power Factor: 0.99 typical at full load. Meets EN61000-3-2 Class A. ENVIRONMENTAL Inrush: Cold start ac current is less than 30 A at 115 Vac and Thermal Protection: Shuts down power supply if overheated. 60 A at 230 Vac. Limited by thermistor. Automatic recovery. Brownout Protection: Holds regulation to 85 Vac. Temperature Range: 0° to 50°C at full ratings. Holdup Time: 20 ms minimum after removal of power at full load. Safety Agencies: Most models are approved to UL1950; CSA Efficiency: 70% typical. 22.2 #234; IEC 950 and TÜV EN60950, Class 1 SELV., CE 72/23/ Ac Power Fail: Provides TTL “0” 5 ms before output voltage EEC/93/68EEC (low voltage directive). goes out of regulation band upon loss of ac power. Conducted RFI: Meets FCC Part 15, Class A; EN55022 Class B. OUTPUT Output Isolation: Isolated from ground 50 Vdc. Adjustability: Outputs #1 and 2, and 4 factory adjusted to Cooling: Self-cooled by internal ball-bearing fan. nominal ±0.2%. Output #3 tracks #2; initial accuracy ±3%. OPTIONS: Consult factory for available options. Line & Load Reg: Outputs #1, 2, and 4 hold ±2% over ac input range and 0 to 100% load change (preprogrammed slope). AC INPUT (90-264 VAC Continuous Range) Output #3 requires 20% minimum load on outputs #2 and 3 to FUNCTION 115 VAC 230 VAC CONNECTOR hold ±5%. Ripple & Noise: 1% p-p or 100 mV, whichever is greater. Je 1-21L1 in Lw ine See belo Remote Sense (Output #1): Compensates for 250 mV total line Jl 1-23N2 eutra Line drop. Preprogrammed slope remains under ±3 worst case. Open Jd 1-25Sd afety Groun Safety Groun sense lead protection. Temperature Coefficient (Outputs #1, 2, and 4): 0.03% per degree C. DC OUTPUT Stability: 0.1% over 8 hours after 30 minutes warm-up. FUNCTION LOCATION NOTES CONNECTOR Transient Response (Outputs #1, 2, and 4): Output voltage returns to within 1% in less than 500 µs for a 50% load change O0 utput #1Jt 1-10,20,3M# ain Outpu Positronics (measured with rise time and fall time of 200µs). Peak transient J) 1-9,19,29R3 tn (common PLC30M400A1-168- does not exceed 5%. O2 utput #2Jl 1- Mates with pane Overload Protection: All outputs are protected against over J) 1-3 Rd tn (common mounte load and short circuit. Automatic recovery upon removal of fault. O4 utput #3J0 1- PLC30F100 Overvoltage Protection (Outputs #1 and 2): Protects load J) 1-3Rg tn (common connector usin against power supply induced over voltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. O5 utput #4Jt 1-(s +) Floating Outpu crimp contact Peak Output Current: Dual current ratings define continuous Jt 1-6() -) Floating Outpu FC114N2 (14 to 16 AWG and peak currents. The peak current shown can be delivered for a maximum period of 30 seconds. STATUS AND CONTROL Remote Enable: Contact closure to common turns on DC FUNCTION LOCATION NOTES CONNECTOR outputs (recessed pin for “make last, break first” connection). R8 emote SenseJe 1-1Oe utput #1 Sens See abov Remote Inhibit: Contact closure to the negative sense line or a Jn 1-8 Output #1 Sense Rt TTL level “0” turns off dc outputs. D7 c Power GoodJn 1- Reference to commo DC Power Good: Provides a TTL “1” open collector when when #1 Sense Rtn is output #1 is above 4.6 V nominal. terminated Redundancy: Built-in OR-ing diodes, slope program current E6 nableJn 1-1 Reference to commo sharing on all outputs, and self aligning connector provide “hot I7 nhibit J1-2 swap” and “N+1” capabilities. Current sharing remains within 10% A7 c Power Fail J1-1 of the unit’s full output rating while units are in thermal equilibrium. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 76 RMX-350, Multiple Output CommercialModel Power Out OutputNo. Output Current TotalRegulation Notes R0 MX354-1205 31 5 +A 5 V 52 0 ± 2V +k 12 82 /12 Ap ± 3V -A 12 45 ±A 4V 5A .2 52 ± R0 MX354-1212 31 5 +A 5V 52 0 ± 2V +k 12 82 /12 Ap ± 3V -A 12 45 ±A 4V 1A 2 52 ± R0 MX354-1224 31 5 +A 5 V 52 0 ± 2V +k 12 82 /12 Ap ± 3V -A 12 45 ±A 4V 2A 4 32 ± Maximum power form outputs #2, #3 and #4 to be less than 170W A. Output #3 requires 20% minimum load on outputs #2 and 3 to hold ±5%. RMX-350 MECHANICAL SPECIFICATIONS: Dimensions: Inches Millimeters Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 77