350 WATTS POWER FACTOR CORRECTED MULTIPLE OUTPUT, HOT SWAP RMX-350 STANDARD RMX SERIES Featuring: • Diode isolated outputs for hot swap MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 • ÒZero wireÓ slope program current RMX-353-0512 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A sharing for redundancy RMX-354-1205 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 5.2V @ 5A RMX-354-1212 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 12V @ 5A • Self-aligning connector with solid RMX-354-1224 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 24V @ 3A metal machined contacts RMX-354-1512 350 +5V @ 50A +15V @ 4A -15V @ 4A 12V @ 5A • Universal AC input RMX-354-1524 350 +5V @ 50A +15V @ 4A -15V @ 4A 24V @ 3A • 0.99 typical power factor Maximum power from outputs #2, #3 and #4 to be less than 170W • Dual converter design eliminates interaction between logic and RMX Series 350-watt power supplies auxiliary outputs provide new and increased flexibility for • Low ripple and noise on all outputs configuring redundant Òhot swappableÓ • DC power good and AC power fail power systems using a standard signals product. The RMX-350 Series eliminates • True remote inhibit the need for external sheet metal sleds, • Monotonic turn-on and turn-off OR-ing diodes, and a high current inter- face. These switching power supplies are power factor corrected, multiple-output units which contain built-in Schottky OR- ing diodes and a high current connector interface. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 ¥ (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com SEE RMX 350 FORDCINPUT EQUIVALENT 350 WATTS 10.75”x 4.8”x 2.5” RMX-350 RMX-350 3.5 lbs - 1.6 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS INPUT Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; CISPR 22 Class B. AC Input: 90-264 Vac continuous range, 47 to 63 Hz. Internally fused for 7A. Output Isolation: Isolated from ground 50 Vdc. Power Factor: 0.99 typical at full load. Meets EN61000-3-2. Cooling: Self-cooled by internal ball-bearing fan. Inrush: Cold star AC t current is less than 30 A at 115 Vac and 60 A at 230 Vac. Limited by thermistor. Brownout Protection: Holds regulation to 85 Vac. OPTIONS Holdup Time: 20 ms minimum after removal of power at full load. Consult factory for available options. E fficiency: 70% typical. AC Power Fail: Provides TTL “0” 5 ms before output voltage goes out of regulation band AC INPUT (90-264 VAC Continuous Range) upon loss of AC power. FUNCTION 115 VAC 230 VAC CONNECTOR OUTPUT Adjustability: Outputs #1 and 2, and 4 factory adjusted to nominal ±0.2%. Output #3 tracks J1-21 Line Line 1 #2; initial accuracy ±3%. See below J1-23 Neutral Line 2 Line & Load Reg: Outputs #1, 2, and 4 hold ±2% over AC input range and 0 to 100% load J1-25 Safety Ground Safety Ground change (preprogrammed slope). Output #3 requires 20% minimum load on outputs #2 and 3 to hold ±5%. DC OUTPUT Ripple & Noise: 1% p-p or 100 mV, whichever is greater. FUNCTION LOCATION NOTES CONNECTOR Remote Sense (Output #1): Compensates for 250 mV total line drop. Preprogrammed slope remains under ±3 worst case. Open sense lead protection. Output #1 J1- 10, 20, 30 Main Output Temperature Coefficient (Outputs #1, 2, and 4) :0.03% per degree C. Positronics # J1 - 9, 19, 29 Rtn (Common) Stability: 0.1% over 8 hours after 30 minutes warm-up. PLC30M400A1-168.3 Output #2 J1-2 Transient Response (Outputs #1, 2, and 4): Output voltage returns to within 1% in less than Mates with panel J1-3 Rtn (Common) 500 μs for a 50% load change (measured with rise time and fall time of 200μs). Peak mounted transient does not exceed 5%. PLC30F1000 Output #3 J1-4 Overload Protection: All outputs are protected against overload and short circuit. Automatic connector using J1-3 Rtn (Common) recovery upon removal of fault. crimp contacts Output #4 J1-5 (+) Floating Overvoltage Protection (Outputs #1 and 2): Protects load against power supply induced over- FC114N2 Output voltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. (14 to 16 AWG) J1-6 (–) Floating Peak Output Current: Dual current ratings define continuous and peak currents. The peak Output current shown can be delivered for a maximum period of 30 seconds. Remote Enable: Contact closure to common turns on DC outputs (recessed pin for “make last, break first” connection). STATUS AND CONTROL Remote Inhibit: Contact closure to the negative sense line or a TTL level “0” turns off DC FUNCTION LOCATION NOTES CONNECTOR outputs. Remote Sense J1-18 Output #1 Sense DC Power Good: Provides a TTL “1” open collector when output #1 is above 4.6 V nominal. Redundancy: Built-in OR-ing diodes, slope program current sharing on all outputs, and self J1-8 Output #1 Sense Rtn aligning connector provide “hot swap” and “N+1” capabilities. Current sharing remains DC Power Good J1-7 Reference to Common within 10% of the unit’s full output rating while units are in thermal equilibrium. when #1 Sense Rtn See above Reverse Voltage: Protected against reverse voltage up to supply current rating. is terminated ENVIRONMENTAL Enable J1-16 Reference Thermal Protection: Shuts down power supply if overheated. Automatic recovery. to Common Inhibit J1-27 Temperature Range: 0°to 50°C at full ratings. Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV AC Power Fail J1-17 EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive). Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 ¥ (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com