Manufacturers
SL POWER / CONDOR POWER FLU3-40-3AD
Description
SL Power/Condor Power FLU3-40-3AD Power Supply - Power Supply; 40 W; 85 to 265 VAC; UL Listed, CSA Certified, CE Marked; 5 V
Part Number
FLU3-40-3AD
Price
Request Quote
Manufacturer
SL POWER / CONDOR POWER
Lead Time
Request Quote
Category
PRODUCTS - F
Datasheet
Extracted Text
40W OPEN-FRAME SWITCHING POWER SUPPLIES ✔ Single, Dual and Triple Output Models ✔ Universal AC-Input and DC-Input Models ✔ CE Mark: UL/CSA/EN60950 Approvals ✔ BABT Approvals ✔ Austel CCL Certification ✔ EN55022/FCC Class B Input Line Filter ✔ 0% Minimum Load Requirement ✔ Over-Current/Short-Circuit Protection ✔ 2-Year Warranty ✔ Minimum 200,000-Hour MTBF Output Current Output CHARACTERISTICS Output Voltage Min. Nom. Max. Voltage Line Load Cross- Model Output (V) (A) (A) (A) Tol. Reg. Reg. Reg. Input Voltage.............................FLU models, universal input range 85-265 VAC single phase or 100-370 AC-DC Singles 85-265 VAC Input VDC. DC input models, 36-75 VDC FLU1-40-1AD V1 5 0.0 8.00 8.00 1.0% 0.1% 0.2% — (48V, nominal). FLU1-40-2AD V1 9 0.0 4.40 4.40 1.0% 0.1% 0.2% — Input Line Frequency ................FLU models, 47-440 Hz (50-60 Hz, FLU1-40-3AD V1 12 0.0 3.30 3.30 1.0% 0.1% 0.2% — nominal). FLU1-40-4AD V1 15 0.0 2.70 2.70 1.0% 0.1% 0.2% — Input Line Protection.................MOV transient protected (FLU series). Input line fuse provided on- FLU1-40-5AD V1 24 0.0 1.70 1.70 1.0% 0.1% 0.2% — board. (See Note 1.) FLU1-40-6AD V1 28 0.0 1.40 1.40 1.0% 0.1% 0.2% — EMI Filter...................................Standard. Performance surpasses AC-DC Duals 85-265 VAC Input conducted EMI requirements of FLU2-40-1AD V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — EN55022/FCC Class B by 10 dB, typ. V2 +12 0.0 2.00 3.00 5.0% 0.5% 3.0% 4.0% DC Output.................................See table. (Note 2.) FLU2-40-3AD V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Continuous Output Power.........40W, maximum. V2 +24 0.0 1.00 1.50 5.0% 0.5% 3.0% 4.0% Output Voltage Adjust ...............Primary output adjustable ±5%. FLU2-40-4AD V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Auxiliary outputs fixed. V2 +28 0.0 1.00 1.00 5.0% 0.5% 3.0% 4.0% Efficiency...................................62-75%, typical (nominal input line FLU2-40-7AD V1 15(ISO) 0.0 1.50 2.50 1.0% 0.2% 1.0% — voltage, nominal load conditions). V2 15(ISO) 0.0 1.20 2.00 3.0% 0.5% 1.0% 1.0% Hold-Up Time............................FLU models: 16 ms (115 VAC input), 32 ms (230 VAC input), minimum, at DC-DC Dual 36-75 VDC Input full load DC2-40-1AC V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Overload Protection ..................Power-limit circuit. V2 +12 0.0 2.00 3.00 5.0% 0.5% 3.0% 4.0% Short-Circuit Protection.............Continuous. AC-DC Triples 85-265 VAC Input Over-Voltage Protection............Primary output only. V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Soft Start...................................Standard on all models. 3 FLU3-40-1AD V2 +12 0.0 1.50 3.00 5.0% 1.0% 3.0% 4.0% Design Topology .......................Flyback converter with current-mode V3 -12 0.0 0.50 0.70 5.0% 0.2% 1.0% 1.0% control. V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Frequency of Operation ............40 kHz (fixed). 3 FLU3-40-2AD V2 +12 0.0 1.50 3.00 5.0% 1.0% 3.0% 4.0% Electrical Strength/Isolation......5300 VDC, input-to-output for one V3 -5 0.0 1.00 1.00 3.0% 0.2% 1.0% 1.0% minute. (Note 6.) V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — 4 Noise, Ripple and Spike ...........1% peak-to-peak, maximum. (See FLU3-40-3AD V2 +15 0.0 1.20 2.00 5.0% 1.0% 3.0% 4.0% Note 8.) V3 -15 0.0 0.50 0.60 5.0% 0.2% 1.0% 1.0% V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — Temperature Range ..................-20°C to +70°C. 5 FLU3-40-4AD V2 +24 0.0 0.75 1.50 5.0% 1.0% 3.0% 4.0% Output Power De-Rating...........De-rate output power and current V3 -12 0.0 0.50 0.70 5.0% 0.2% 1.0% 1.0% linearly 2%/°C from +50°C to +70°C. V1 5(ISO) 0.0 5.00 6.00 1.0% 0.2% 0.5% — Temperature Coefficient............±0.05%/°C over the entire operating FLU3-40-5AD V2 12(ISO) 0.0 0.30 0.50 4.0% 0.5% 1.0% 1.0% temperature range. V3 12(ISO) 0.0 0.30 0.50 4.0% 0.5% 1.0% 1.0% Relative Humidity......................0 to 95%, non-condensing. V1 5(ISO) 0.0 5.00 6.00 1.0% 0.2% 0.5% — Altitude ......................................0 to 10,000 feet. FLU3-40-6AD V2 15(ISO) 0.0 0.30 0.50 4.0% 0.5% 1.0% 1.0% Cooling......................................Convection cooling is adequate. V3 15(ISO) 0.0 0.30 0.50 4.0% 0.5% 1.0% 1.0% Moving air is recommended for oper- ation in a confined area. DC-DC Triple 36-75 VDC Input Storage Temperature ................-40°C to +85°C. V1 +5 0.0 3.00 5.00 1.0% 0.2% 1.0% — 3 DC3-40-1AC V2 +12 0.0 1.50 3.00 5.0% 1.0% 3.0% 4.0% Storage Humidity ......................0 to 95%, non-condensing. V3 -12 0.0 0.50 0.70 5.0% 0.2% 1.0% 1.0% Mean Time Between Failures ...>200,000 hours. (Note 9.) POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidec.com · http://www.nidec.com GENERAL Rev. PG/ABBB 24 40W OPEN-FRAME SWITCHING POWER SUPPLIES FLU AND DC 40W SERIES A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. P1 input connectors are Molex 26-62-4030. The mating con- nector combines Molex housing 43061-0003 and crimp ter- minal 08-70-1030. D. P2 output connectors for the 40W series, except for models 5 and 6 of the FLU3-40 series, are Molex 26-60-4060. The mating connector combines Molex housing 43061-0006 and crimp terminal 08-70-1030. Models 5 and 6 of the FLU3-40 series use Molex 26-60-4080 for the P2 connector. The mat- ing connector uses Molex housing 43061-0008 and crimp terminals 08-70-1030. Pin-Out FLU2-40 FLU2-40 FLU3-40 FLU3-40 Pin FLU1-40 Models 1, 3 Models 4, 7 DC2-40 Models 1-4 Models 5-6 DC3-40 1 V1 V2 +V1 V2 V2 +V2 V2 (ISO) (ISO) 2 V1 V1 +V1 V1 V1 - V2 V1 (ISO) (ISO) 3V1 V1 - V1 V1 V1 +V1 V1 (ISO) (ISO) 4 Return Common - V1 Common Common +V1 Common (ISO) (ISO) 5 Return Common - V2 Common Common - V1 Common (ISO) (ISO) 6 Return N/C +V2 N/C V3 - V1 V3 (ISO) (ISO) 7 N/A N/A N/A N/A N/A +V3 N/A (ISO) 8 N/A N/A N/A N/A N/A - V3 N/A (ISO) Notes 10. Output voltage tolerance is measured under nominal load current condi- 1. Replace the input line fuse with the same type and rating. tions. Recommended: 2A/250V slow-blow fuse. 11. Line regulation is measured under nominal load conditions as the input 2. The sum of primary and auxiliary output currents from triple output mod- voltage is varied from 85 to 265 VAC (ac-input models) or from 36 to 75 els -1AD through -4AD must not exceed 5.0A. VDC (dc-input models). 3. Peak output current rating = 5.0A (<60 seconds, duty cycle <10%). 12. Load regulation is measured at 115 VAC or 230 VAC. For single output 4. Peak output current rating = 3.0A (<60 seconds, duty cycle <10%). models, load regulation is measured while output current is varied from 0% to 100% of full load. With multiple output models, the output under 5. Peak output current rating = 2.0A (<60 seconds, duty cycle <10%). test is brought to 60%of nominal load; load current is then varied +40%/- 6. Electrical strength/isolation is 2200 VDC from the input of the power sup- 30% of nominal while other outputs are held at nominal load conditions. ply to ground for 60 seconds. 13. Cross-regulation is tested by changing the load on the primary output 7. All measurements are made directly at the terminals of the power supply. from 50% to 100% of nominal load while measuring the voltage change 8. Peak-to-peak and RMS metering equipment must have a 20 MHz fre- on the auxiliary output under test. quency response with probes and cables that maintain a frequency 14. The FLU1-40, FLU2-40 and FLU3-40 series are approved to UL1950 response of 20 Hz to 20 MHz. Output ripple and spikes are measured (File E140439), CSA22.2 No. 234 (File LR52335), EN60950/IEC950/DIN directly at the output terminals of the power supply with a 0.1 µF ceramic VDE 0805 (TÜV Licenses R9679206, R9779161, R9779037), and Austel capacitor. The probe ground band must make direct contact with the out- CCL (Certificate A92/PS/004). put return or common terminal to prevent erroneous noise measure- 15. The FLU3-40 series has BABT/EN41003 approval /4199/123/R/604674). ments. 16. The DC2-40 and DC3-40 series are approved to UL1950 (File E140439), 9. MTBF is calculated using the parts stress method in MIL-HDBK 217F CSA22.2 No. 234 (File LR52335), and EN60950/IEC950/DIN VDE 0805 (ground benign, TA = +25°C). (TÜV License R9071501). POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidec.com · http://www.nidec.com GENERAL Rev. PG/ABBB 25
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the FLU3-40-3AD have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods