SEAGATE ST340014A

Computer Motherboard  Master with non-ATA compatible slave: Use this setting if the slave drive is not recognized. Configure the master drive with a jumper set on pins 5 and 6 and pins 7 and 8 to enable this option.  Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the inter- Barracuda 7200.7 Installation Guide face bus. To enable cable select, set a jumper on pins 5 and 6. ST3200822A, ST3200021A, ST3160021A, ST3160023A, ST3120022A,  Alternate capacity jumper: Drives ST3120026A, ST380011A, ST380013A, and ST340014A with a 40-Gbyte capacity or greater Options jumper block ATA Interface Disc Drives are limited to 32 Gbytes. Use this *Master or single drive jumper only if you have a legacy sys- Publication Number: 100217284, Rev. B, September 2003 Drive is slave tem with a BIOS that does not support Master with non ATA- large capacity disc drives. When compatible slave The easiest way to install your drive using the alternate capacity jumper, *Cable select TM DiscWizard , available exclusively from Seagate®, provides you with cus-  Manager software is required to Alternate capacity. tomized installation instructions for your hard drive. You can get this free Limits drive capacity achieve the drive’s full capacity. to 32 Gbytes disc drive installation software from our web site at www.seagate.com/sup- 753 1 port or run the program directly from your web browser. In either case, you Attaching cables and mounting should run DiscWizard before you install your drive. the drive 84 6 2 To run DiscWizard: 1. Attach one end of the drive interface Follow the instructions on the download page at www.seagate.com to cre- cable to the interface connector on your computer’s motherboard (see ate a diskette and complete the installation. your computer manual for connector locations). If you cannot run DiscWizard, follow the instructions on this installation Note. When configuring two ATA devices on sheet to install and configure your drive. the same cable, both must use Cable Select or both must use Master/Slave Master What you need Pin 1 jumper settings. If using a standard 40-pin cable, the master and slave  A Phillips screwdriver and four 6-32 UNC drive mounting screws drives can be placed in any position. If Slave  An ATA interface cable. For optimum drive performance and data integ- using a 40-pin 80-conductor cable, attach rity, use an 80-conductor Ultra ATA/100 cable (which can be identified by the blue connector to the motherboard, its blue, gray, and black connectors). the black connector to the master drive and the grey connector to the slave. Ultra ATA/100 requirements Caution. Align pin 1 on the motherboard connector with pin 1 on your The drive can be configured to support a default maximum transfer rate. drive connector. Pin 1 is marked by a stripe on one side of the This drive can support transfer rates up to 100 Mbytes per second (UDMA cable. 5) in Ultra ATA/100 mode. Using a software utility, you can set the default 2. Secure the drive using four 6-32 UNC mounting screws in either the transfer rate to the best capability of your system. For your drive to run in side-mounting or bottom-mounting holes. Insert the screws no more this mode, you need the following: than 0.20 inches (5.08 mm) into the bottom-mounting holes and no  A computer that supports UDMA mode 5 more than 0.14 inches (3.55 mm) into the side-mounting holes.  A 40-pin, 80-conductor cable (available from your computer dealer) Note. Do not overtighten the screws or use metric screws. This may dam-  A software utility to confirm and activate Ultra ATA/100. Seagate pro- age the drive. vides a utility called UATA100.exe. You can download the latest version 3. Attach the interface connector and the power connector to the drive. from our web site at www.seagate.com. Key on cable connector  Windows XP, Windows Me, or Windows 98 operating system which sup- fits into slot on drive connector ports Ultra ATA 100. Large disc requirements (for capacities over 137 Bytes) To realize the full capacity of drives over 137 Gbytes:  Use an operating system that supports 48-bit addressing: - Microsoft Windows XP Home with Service Pack 1 Pin 1 Power connetor - Microsoft Windows XP Professional with Service Pack 1 Stripe on cable - Windows 2000 Professional with Service Pack 3 - Windows 2000 Server with Service Pack 3  Use a 48-bit compatible Ultra ATA/133 PCI host adapter card or connec- tor on your motherboard. Configuring the BIOS See the http://support.seagate.com for additional information. Close your computer case and restart your computer. your computer may automatically detect your new drive. If your computer does not automati- Handling precautions/electrostatic discharge protection cally detect your new drive, follow the steps below.  Disc drives are fragile. Do not drop or jar the drive. Handle the drive only a. Restart your computer. While the computer restarts, run the System by the edges or frame. Setup program (sometimes called BIOS or CMOS setup). This is usu-  Drive electronics are extremely sensitive to static electricity. While ally done by pressing a special key, such as DELETE, ESC, or F1 dur- installing the drive, wear a wrist strap and cable connected to ground. ing the startup process.  Turn off the power to the host system during installation. b. Within the System Setup program, instruct the system to auto detect  Do not disassemble the drive; doing so voids the warranty. Return the your new drive. entire drive for depot service if any part is defective. c. Enable LBA and UDMA modes, if available and then save the settings  Do not apply pressure or attach labels to the drive. and exit the Setup program. Setting the jumpers When your computer restarts, it should recognize your new drive. If your system still doesn’t recognize your new drive, see the troubleshooting sec- Refer to the jumper settings illustration below or on your drive label to con- tion on the back of this sheet. figure the drive for your system. Jumper settings can also be accessed online from our web site at www.seagate.com.  Master or single drive: The drive is shipped configured for a master or a single drive with a jumper set on pins 7 and 8.  Drive is slave: To configure the drive as a slave or second drive on the cable, remove all the jumpers. BIOS Settings defects. If defects are detected, this may be an indication of a problem. Drive Model Formatted Gbytes Total Sectors* 5. Why won’t the drive format to full capacity? Verify that your BIOS ST3200822A 200.0 490,721,968 has autodetect and LBA mode enabled. Otherwise, you may need to ST3200021A 200.0 490,721,968 use Disk Manager to achieve the full capacity of your drive. Download the latest version from www.seagate.com or find it on your CD. ST3160021A 160.0 312,581,808 ST3160023A 160.0 312,581,808 6. Why does my computer hang on startup? Verify that your system is ST3120022A 120.0 234,441,648 ATA/100 compatible with the UDMA mode setting. Some legacy BIOS ST3120026A 120.0 234,441,648 cause hangs on startup or other problems if it is not ATA/100 compati- ble. For more information, see the earlier section on the Ultra ATA/100 ST380011A 80.0 156,301,488 requirements. In addition, some legacy BIOS may cause a hang due to ST380013A 80.0 156,301,488 the large drive capacity. Consider using the alternate capacity jumper if ST340014A 40.0 78,165,360 it is available on your drive model. *One sector equals 512 bytes. Use the alternate capacity jumper if your computer does not support Preparing the drive using DiscWizard higher capacity drives. The jumper will limit large capacity drives to 32 Gbytes. Installing a single drive Note. If these tips do not answer your question or solve the problem, con- If you are installing a single drive, we recommend using DiscWizard to tact your dealer or visit http://seatools.seagate.com to download automatically partition and format your drive. DiscWizard software is avail- SeaTools disc diagnostics software and more troubleshooting able at www.seagate.com and is free. During the download, the Diskette advice. Creator creates a portable bootable diskette. To run DiscWizard: 1. Insert your bootable DiscWizard diskette and follow the instructions. Seagate support services DiscWizard will guide you through the installation process. For online information about Seagate products, visit www.seagate.com or 2. Boot your computer from the Windows operating system CD-ROM or e-mail your disc questions to DiscSupport@Seagate.com. from your system startup diskette with the Windows CD loaded. At the If you need help installing your drive, consult your dealer first. If you need prompt, type setup. Follow the instructions provided on your screen. additional help, call a Seagate technical support specialist. Before calling, Installing a slave drive note your system configuration and drive model number. If you are installing a second drive, or slave, to your system, use the Dis- Africa +31-20-316-7222 Netherlands 0 800-732-4283 cWizard software available at www.seagate.com. Australia 1800-14-7201 New Zealand 0800-443988 Austria 0 800-20 12 90 Norway 800-113 91 If you do not want to install your drive using either DiscWizard or Disk Man- Belgium 0 800-74 876 Poland 00 800-311 12 38 ager, see “Standard Microsoft Installation” below to partition and format China* 800-810-9668 Spain 900-98 31 24 your drive. Denmark 80 88 12 66 Sweden 0 207 90 073 France 0 800-90 90 52 Switzerland 0 800-83 84 11 Standard Microsoft installation Germany 0 800-182 6831 Singapore 800-1101-150 Hong Kong 800-90-0474 Taiwan* 00-800-0830-1730 Caution. Partitioning or formatting a drive erases all data on the drive. Hong Kong* 001-800-0830-1730 Thailand 001-800-11-0032165 Seagate assumes no liability if you erase your data. India 1-600-33-1104 Turkey 00 800-31 92 91 40 1. Insert a bootable Windows startup diskette and restart your computer. Indonesia 001-803-1-003-2165 United Kingdom 0 800-783 5177 Ireland 1 800-55 21 22 USA/Canada/ 1-800 SEAGATE or This is provided with your Microsoft Windows operating system soft- Italy 800-790695 Latin America +1-405-324-4770 ware. Malaysia 1-800-80-2335 Other European 2. Run fdisk and create a primary DOS partition. Middle East +31-20-316-7222 countries +31-20-316-7222 *Chinese 3. Mark the partition as active to make the partition bootable. Warranty. To determine the warranty status of your Seagate disc drive, contact your Drive formatting place of purchase or visit our web site at www.seagate.com for more information. Caution. Use the correct drive letters to prevent formatting a drive that Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is already contains data. defective by following the troubleshooting checklist in this guide. Seagate offers com- 1. At the A: prompt, type format x: (where x is the letter of your first new prehensive customer support for all Seagate drives worldwide. Seagate customer partition) and then press the Enter key. Repeat the format process for service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current all new partitions. international trade regulations. 2. Proceed to “Loading the operating system” below. Shipping the drive Loading the operating system Caution. Back up the data before shipping. Seagate assumes no responsibility for data lost during shipping or service. Note. The operating system needs to be installed on the master drive Shipping drive in an unapproved container voids the warranty. Pack the drive with only. It is not required when adding a second drive. original box and packing materials. Use no other materials. This prevents electrical 1. Boot your computer from your Windows operating system CD-ROM or and physical damage in transit. from your system startup diskette with the Windows CD loaded in the Electromagnetic compliance for the European Union. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ CD drive. 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and 2. At the prompt, type setup and continue with the Windows setup as Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system compo- instructed on your screen. nent, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, Troubleshooting shielded I/O cable, etc.). If your drive is not working properly, these troubleshooting tips may help Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks solve the problem. werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maxi- 1. Does the drive spin up? A spinning drive produces a faint whine and male Länge der Schrauben im Chassis nicht merh als 3,3 mm und bei Befestigung an clicking noise that begins when power is applied. If your drive does not der Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen wer- den benötigt: +5V +/- 5% 1,2A; +12V +/- 5% 2,0A 4. Die Versorgungsspannung muss spin, check that the power connector and interface cable are securely SELV entsprechen. 5. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem attached and the jumpers are installed correctly. Serciepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftens- 2. Does the computer recognize the drive? Verify that the drive is childer des Laufwerkes. 6. Der Einbau des Laufwerkes muss den Anforderungen enabled in the system CMOS or setup program. If not, select the auto- gemäss DIN IEC 950 VDE 0805/05.90 entspreche. detect option and enable it. If your drive has a problem, it may not be © 2003 Seagate Technology LLC. All rights reserved recognized by the system. Publication number: 100217284, Rev. B, September 2003, Printed in U.S.A. 3. Does FDISK detect the drive? Run the FDISK program located on Seagate, Seagate Technology, and the Seagate logo are either registered trademarks your Windows startup diskette. Type fdisk/status to verify that your or trademarks of Seagate Technology LLC. Barracuda is a registered trademark of hard drive is present and recognized by the system. Seagate Technology LLC. Other product names are registered trademarks or trade- 4. Does Scandisk find the drive defect-free? Scandisk is a utility marks of their owners. Seagate reserves the right to change, without notice, product located on your Windows startup diskette that scans the drive for offerings or specifications.