AC Fail (optional)

Designated as ACF on the CN3 to monitor the input voltage, when input goes under 80 +'- 5VAC the signal will go low (OV) and then go high (+5V) once reappears over 86VAC.

Adjustability

Output user adjustable +?-5°o minimum.

Burn In

45 +'- 5 degree C for I hour @23OVac with full load.

Cooling

U-Chassis ©40OW max. with 23CFM airflow or 25OW max. under convection cooling.

Current Monitor

Designated as CMN on the CN3 for current sense for a 0 5V to 3VDC to represent 0% to 100% output current.

Current sharing

Designated as CSH on the CN3, optional single wired for forced current sharing function and parallel up to 4 units

Efficiency

70% for 3.3V. 75% for 5V, 80% for 12V and 83% minimum for others output @ 230V and full load.

Emissions

FCC Part 15, CISPR 22 class B, Conducted.

Enclosure

8 (L) x 5(W) x 1.6(H) inches.

Fan Drive

12VDC'400mA is available to drive an external fan.

HI-POT Test:

1 500 Vac between input line and chassis (2mA DC cut off current): 4000Vac between primary and secondary windings, Primary to core 1500VAC. All for 3 sec.

Input Circuit Protection (primary)

Two T8A/250V fuses inserted.

Input Current

6.35A at 90VAC full load.

Input Voltage

90-264Vac full range, 47-63Hz.

Input Voltage Protection

Power shut down under 80 +/-5Vac, and recovered over 86Vac.

Inrush Current

35A Max @ 230VAC with full load and cold start.

Leakage Current

Medical degree 300uA

LED display

Bi-color green LED in front panel (RL0402E only), Any protection occurred or RSW applied low signal will emit orange.

Margin

Designated as MAG on the CN3 providing 50°/o of output voltage remote adjustment by applying 0 4 - 5V signal on MAG.

MTBF

100000 Hrs (according to MIL-HBK-217F) at 30 C .

Operating Humidity

5% to 90% RH, Non-condensing.

Over Temperature Protection

Protected in the event of excessive operating ambient 85 degree, and automatic recovery.

Over-Power Protection

C.C. node 110-140% and auto-recovery

Over-voltage Protection

Latching down will occur when output voltage exceed 130% and recycle AC input to reset.

PFC

Active power factor correction meet EN6 1000-3-2 class D.

Power Good

Designated as PG on the CN3 will go high 100-500mS after regulation and goes low 1 mS before loss of regulation.

Power Supply On

Green LED designated as LED 1 on the PCB.

Remote On-Off

Designated as RSW on the CN3, requires a low signal to inhibit output.

Remote sense

Designated RS+ and RS- on the CN3.

Safety Regulation

Approved to UL 60601-1. CSA 601.1-M90, TUV 60601-1. CE Mark (LVD) EN61204-3/ 60601-1-2/ 61000-3-2.3 & I EC61000-4 Series Regulations and CB.

Short circuit protection

Trip without damage and auto-recovery.

Storage Humidity

5% to 95% RH, Non-condensing.

Storage Temperature

-20 to 85 degrees C.

Transient response

Returns to within 1% in less than 2.5mS for a 50% load change and the peak transient does not excess 5%.

TURN ON DELAY

1 second maximum at 120 VAC. Hold Up Time: 20mS min_ at 80% of full load.

Vibration

Frequency 5 to 50 Hz, acceleration +;-7.35 M/(SxS) on X.Y and Z Axis.

Warranty

2 years.

Weight

1.3KG