CL9 ® High Performance – 3U CompactPCI Intel® Pentium® M Processor Board Features ® ® • Intel Pentium M processor, ® 1.4 GHz to 1.8 GHz and Intel ® Celeron M processor 1.0 GHz and 1.3 GHz • Up to 2MB L2 cache • Ultra compact all-in-one PC • System slot for 32-bit CompactPCI backplane • Up to 1GB DDR SDRAM • Flash drive up to 4 GB or local 2.5” hard disk • VGA/DVO interface Single slot version not shown • Dual Gigabit Ethernet ® • Enhanced IDE UDMA-100 CL9 is a high-performance 3U CompactPCI CPU board using the low power â â Intel Pentium M Processor incorporating sophisticated power management • Dual Serial ATA technology, eliminating the need for an onboard fan. The CL9 is available in two different front options (1 or 2 slot width), enabling the user to select the feature set • 2x serial I/O with FIFOs required for the target application. The CL9 runs in the system slot of the RS-232 interface CompactPCI backplane. • 4x USB 2.0 The single slot version contains a CompactFlash as an option. The 8HP version optionally contains an integrated hard disk or CompactFlash. The • Optional audio interface 8HP versions offer the user the choice between a DVI interface or a COM2 port on • Watchdog, temperature the front. In place of the COM1an audio interface AC’97 can be integrated if the operating temperature is not below 0 °C. sensor The CL9 supports two Gigabit Ethernets, up to 1 Gbyte of DDR SDRAM and • 5V / 3.3V supply supports VGA/DVO. At the core of the CL9 design is a high-bandwidth bus between the processor and the chipset running at 400MHz bus. The chipset-to-memory bus • Optional -40°C to +75°C supports 333 MHz (PC2700) DDR SDRAMs. In addition there are four USB 2.0 ports, two serial channels, and two serial ATA channels. Interfaces are available as front- and/or rear-I/O. The CL9 is available in standard temperature range 0° to +70°C, and • Custom specific versions optional in extended from -40°C to +75°C. Custom specific versions are available on request. The CL9 is a powerful processor platform for a wide range of applications and markets such as multimedia, automation, transportation, as well as imaging, medical, robotics, and many others. The CL9 is very suited to low-power embedded computer applications in a small form factor where optimal performance and functionality is required. Single Board Computers Specifications Serial I/O - RS232 · Integrated in chipset · Two async. 16550 compatible full duplex serial channels Processor - µFCBGA, Low Power design · High-speed transfer up to 115.2 kbaud with 16 byte FIFOs · Scaleable processing power with flexible processor design · COM1 and COM2 optional available at front (8HP) or rear I/O · Intel Pentium M processor: 1.4 GHz to 1.8 GHz · With 8HP extension card other interface types are supported · Intel Celeron M processor: 1.0 GHZ and 1.3 GHz (e.g. RS485) · High efficiency on-board switching regulator (DC/DC) · Fanless cooling with heat sink Audio AC’97 Interface - optional · See price list for latest CPU versions · S/PDIF digital output (optical) · Line in Cache level 1 level 2 · Headphone out Pentium M (90nm) 32 KB 2MByte, full speed · Note: The audio interface does not operate below 0 °C Pentium M (130nm) 32 KB 1MByte, full speed Celeron M (130nm) 32 KB 1MByte, full speed General Purpose Input/Outputs Celeron M (90nm) 32 KB 512KByte, full speed · 8 bits programmable general purpose inputs/outputs Chipset – Intel 855GME with 6300ESB USB 2.0 · 400 MHz system bus to processor · Four USB 2.0 connectors, one or two (8HP) on front and two · PCI burst mode transfers up to 512 MB/s (64-bit/66 MHz) on rear I/O · One 64-bit wide PCI-Xbus with 66 MHz · One 32-bit wide PCIbus with 33 MHz Keyboard · Data throughput between 855GME and 6300ESB is 256 MB/s · Via USB (supports legacy keyboard/mouse SW) (theoretical) Mouse Memory – DDR 333 · Via USB (supports legacy keyboard/mouse SW) · High-speed 333MHz (PC2700) DDR SDRAM · 64-bits wide Real-time clock · 512 Mbytes to 1 Gbyte with soldered chips · Integrated in chipset · RTC 146818 compatible, on-board Li-battery CompactPCI · PICMG 2.0 R3.0 compliant CPCI 32bit/33MHz local bus CMOS RAM standard · 114 bytes non-volatile CMOS RAM for BIOS data · Backplane with rear I/O · System only PCI Bridge TI PCI2050B for up to 7 slots EEPROM · J1+2, 2 mm pin and socket connectors (IEC-1076-4-101) · 1Mbit (128kByte) serial EEPROM for non-volatile user data Gigabit – Intel 82546GB Floppy · Highly integrated Dual Ethernet Controller with 64-bit/66 MHz · Via USB port PCI-X local bus DMA · 64 Kbyte Transmit and Receive FIFO Watchdog · 10/100/1000BaseT auto-negotiation · Integrated in chipset · Both channels at front I/O with RJ45 connectors and status · Two stage watchdog with independent count values LEDs · First stage drives NMI or SMI, second stage drives reset · Configurable granularity from 1ms to 10min Hard Disk or Flash Drive · EIDE interface on header connector for two devices Timer · Extension board with one Compact Flash connector (4HP) · Integrated in chipset based on 82C59 · On extension card (8HP) for one 2.5” IDE hard disk or one · Includes three timer comparators Compact Flash connectors (for extended temperature range · One-shot and periodic interrupts supported and higher shock/vibration immunity) Temp. Sensor VGA and LCD - Chipset Integrated · CPU die and heat sink temperature software readable from · 2D & 3D graphics engine –65°C to +127°C · Up to 64MB of dynamic video memory allocation · Integrated 350MHz 24-bit RAMDAC for analog VGA monitors LED up to 1600 x 1024, 75Hz · Two LEDs at front panel · Integrated Digital Video Output (DVO) Port interface · Dual independent pipe support BIOS Features · Display image rotation · New AMI BIOS Core 8, in-system programmable Flash ROM · Graphics power management · CPU, memory and IDE auto-detection/selection · VGA at front and rear I/O · Integrated VGA, and Ethernet BIOS ROM · DVO at connector, with extension card DVI-D support possible · USB Mass Storage support · Password protection, BIOS post, system and video BIOS EIDE shadowing · Ultra ATA/100 sync. DMA mode up to 90 Mbytes/sec · Extensive setup with remapable serial/parallel ports · PIO mode 4 and bus master IDE up to 16 Mbytes/sec · Operation without disk and keyboard · Onboard devices supported via local header · Remote BIOS through serial port SATA Power Requirements Software · +5 V, +3.3V Required · The following software is supported to the extent listed below. Power Consumption - typical operating current (estimated) · 512 MB memory bank, w/o keyboard, hard disk, modules, etc. OS On Request Available WIN XP - Ö Pentium M 5 V 3.3 V Total Power QNX 6 Ö - 1.0 GHz A A W Celeron M VxWorks - Ö 1.3 GHz A A W Celeron M Lynx OS Ö - 1.4 GHz A A W Linux - Ö 1.6 GHz 3.7 A 2.4 A 26.5 W 1.8 GHz 2.9 A 2.4 A 22.5 W Front and Onboard I/O With standard Front Panel (8HP) Operating measured at DOS prompt, no power saving Mechanical – PICMG 2.0 Function Front I/O On-board I/O Rear · 3U, 1 slot wide (100 x 160 x 20.32mm) with 4HP Front panel I/O · 3U, 2 slot wide (100 x 160 x 40.64mm) with 8HP Front panel Giga Ethernet 0 RJ-45 · CL9 at backplanes with right justified system slot occupies Giga Ethernet 1 RJ-45 one CPCI slot only. USB 0 USB USB 1 USB Temperature USB 2/3 yes · Note: For detailed information about the operating temperature VGA D-15 yes *1 behavior of the board it is absolutely necessary to consult the DVO DVI-D manual. The highest achievable operating temperature EIDE yes depends on processor type, speed, ambient conditions (air SATA 1 yes flow) and front plate width. SATA 2 yes · All values under typical conditions. COM 1 D-09 yes COM 2 D-09 yes Operating Storage *2 Audio AC’97 Yes Standard 0°C to +70°C –40°C to +85°C GPIO (8 pins) yes Extended -40°C to +75°C –40°C to +85°C Reset Button yes Speaker Yes Humidity LED Yes · Operating: 5 - 95% @ 40°C Keyboard, Via USB Via · Storage: 5 - 95% @ 40°C mouse, Floppy USB *1 Possible with special extension card, COM2 front I/O not Altitude available · Operating: 15.000 ft. (4.5 km) *2 Only available for operating temperature range ≥ 0 °C · Storage: 40.000 ft. (12 km) Front and Onboard I/O Shock With standard Front Panel (4HP) · C-, I-.Style 12g / 6 ms, 3 axis, up & down, 5 hits / direction Function Front I/O On-board I/O Rear Vibration I/O · C-, I-.Style 2 g rms @ 5 to 100 Hz, 30 minutes each axis Giga Ethernet 0 RJ-45 MTBF Giga Ethernet 1 RJ-45 · Calculations are available in accordance with MIL-HDBK-217. USB 0 USB Please contact factory. USB 1 Header USB 2/3 Yes Safety VGA D-15 Yes · Designed to meet standard UL 1590, CE class A, FCC-A DVO Header EIDE Header SATA 1 Yes SATA 2 Yes COM 1 Header Yes COM 2 Header Yes GPIO (8 pins) Yes Reset Button Yes Speaker Yes LED Yes Keyboard, Via USB Via mouse, Floppy USB CL9 Block Diagram Intel® Pentium®M Processor Intel® VGA / 1 GB DDR 855GME LCD SDRAM VGA / LCD 266 MB/s CPCI 2x GbE Bridge 2x SATA 2x COM Intel® 6300ESB 1x EIDE 4x USB Watchdog AC’97 Timer RTC, GPIO SMB Ordering Information Hardware Accessories CTM15: I/O transition module for 3U backplane SCC484TC08CL9: Starter cage 19” 4U with fans, power supply, CDROM and hard disk Operating Systems Extensive operating systems support is available (see page 3). Chassis with power supplies, backplanes and drives on request. For detailed information and further options, contact SBS. Corporate Headquarters European Headquarters 7401 Snaproll NE Memminger Str. 14 Albuquerque, NM 87109 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2006 SBS Technologies, Inc. 20060627