CT9 High Performance – PICMG 2.16 ® 6U CompactPCI Server Blade Features ® ® • Intel Pentium M CPU, 600 MHz to 1.6 GHz • Optimized for telecom applications • Ultra compact, 1 slot • Hot Swap (Full) PICMG 2.1 compliant • System & Non-system (peripheral) mode • Extensive Software Support • Up to 2 GB DDR SDRAM (200) with ECC • Flash Drive up to 1 GB or local 2.5” hard disk ® CT9 is a 6U CompactPCI all-in-one CPU board with integrated low power Intel • VGA/LCD up to 2048x1536, ® Pentium M processor and dual Gigabit Ethernet channels. The CT9 supports full hot swap 16/32MB DDR SDRAM and is capable of being used in a system or non-system (peripheral) slot. Adhering to the • Two Gigabit Ethernet PICMG 2.16 dual Ethernet specification, the CT9 supports the 64-bit/66 MHz CompactPCI ports10/100/1000 BaseT bus and is designed for use in a broad range of applications such as wireless base stations, front or rear optional voice over packet, enterprise devices, test and measurement systems, and server blade applications. • PICMG 2.16 compliant The CT9 platform is designed to support processors starting with 600MHz up to 1.6 GHz. • Two PMC extension slots, It offers low power consumption and eliminates the need for on-board fans. The design is one 64-bit/66 MHz and one ready to accept future higher performance Intel Pentium M processor versions. 32-bit/33 MHz • IPMI PICMG 2.9 The CT9 provides a unique feature set, including up to 2 GB of 200 MHz DDR SDRAM with ECC, three independent on-board PCI buses, high speed support for the CPCI • Ultra ATA/100 onboard, backplane, two PMC interfaces (64-bit/66MHz and 32-bit/33 MHz). A high level of second channel rear I/O functional integration (VGA/TFT, USB, serial interfaces, etc.) within a single slot gives users • 2x serial I/O with FIFOs the freedom to use the PMC interfaces as extension for their applications. This combined RS-232/422/485 interface with a custom specific assembly service provides optimized price/performance for all kinds of OEM applications. The board is also available in extended temperature version ranging • USB 2.0 ports, one front, from -40° to +55° C. 4 rear The CT9 also includes a Baseboard Management Controller (BMC) supporting the • Watchdog, temperature Intelligent Platform Management Interface (IPMI) architecture. It allows independent sensor platform management between IPMI enabled boards, power supplies, fans and other • Optional –40°/+55°C accessories in a system. This feature can be used for autonomous monitoring, logging and recovery control functions. • Customer specific, low cost assembly versions ® ® ® ® Supported operating systems are Windows 2000, Windows XP, QNX, VxWorks , Linux ® and LynxOS (on request). SINGLE BOARD COMPUTERS Specifications ® ™ VGA and LCD – NVIDIA GeForce 4 410/420 Go • 256-bit 3D and 2D graphics accelerator • On-chip 16/32 Mbytes frame buffer (66-190 MHz) CompactPCI - Hint HB6 PCI-to-PCI Bridge • 32-bit/33 MHz PCI interface • PICMG 2.0 R3.0 compliant CPCI local bus standard ™ • NVIDIA Digital Vibrance Control technology • 64-bit PCI-to-PCI bridge for up to 8 slots (33 MHz) • Dual CRTC/Simultaneous Dual Display (same or different surfaces) or 5 slots (66 MHz) • Integrated 350MHz Palette-DAC for analog VGA monitors up to • Supports System and Peripheral Mode 2048x1536 • J1+2, 2 mm pin and socket connectors (IEC-1076-4-101) ® • DVI-I interface PanelLink single channel for TFT displays up to 1280x1024 true color (EDID displays PnP supported) Processor - µFCBGA, Low Power Design • Fully compliant support for OpenGL 1.2 for all Windows • Scalable processing power with flexible processor design operating systems and Linux • Intel Pentium M processor: 600 MHz to 1.6 GHz • Versions with front or rear-I/O available • High efficiency on-board switching regulator (DC/DC) • Note: No video output is available if connector J4 is not • Fanless cooling with heatsink populated and if a PMC module is attached on PMC2 • See price list for latest CPU versions EIDE- ICH4 Chipset – Intel E7501/P64H2 • Ultra ATA/100 sync. DMA mode up to 100 Mbytes/sec • 400 MHz system bus to processor • PIO mode 4 and bus master IDE up to 16 Mbytes/sec • PCI burst mode transfers up to 512 MB/s (64-bit/66 MHz) • Two devices supported via local EIDE connector and two devices • Two 64-bit wide PCIbusses with 66 MHz alternative with PMC32/33 rear I/O • One 32-bit wide PCIbus with 33 MHz Serial I/O - RS232/422/485 Cache level 1 level 2 • Two async. 16550 compatible full duplex serial channels at rear I/O Pentium M 32 KB 1024 KB, full speed • High-speed transfer up to 115.2 kbaud with 16 byte FIFOs • User selectable RS232/422/485 interface Memory – DDR 200 • COM1 optional available at front • High-speed registered DDR SDRAM • 72-bit wide with error correction (ECC) Parallel Port • 128 Mbytes to 2 Gbyte with soldered chips • Bi-directional, IEEE 1284 compatible enhanced parallel port • Note: Memory speed depends on selected processor type (including EPP and ECP) for printer Dual Gigabit Ethernet – Intel 82546GB USB 2.0 – ICH4 • Highly integrated Dual Channel Ethernet Controller with • One USB 2.0 connector at front 64-bit/66 MHz PCI local bus DMA • 4 universal serial bus channels at rear • 64 Kbyte Transmit and Receive FIFO • 10/100/1000BaseT auto-negotiation Keyboard • Versions with front I/O available • PS/2 compatible • Compliant to PICMG 2.16 Mouse Hard Disk or Flash Drive • PS/2 compatible • Internal 2.5” IDE hard disk or 2.5” flash drive (for extended temperature range and higher shock/vibration immunity) Real-time clock • RTC 146818 compatible, on-board Li-battery PMC Extension Slots - IEEE P1386/1386.1 • Compliant to VITA 30.1-2001 and ANSI/VITA 20-2001 CMOS RAM • One high bandwidth 64-bit/66 MHz PMC interface • 114 bytes non-volatile CMOS RAM • 32-bit/33 MHz PMC slot supports front panel I/O and rear I/O • 32-bit/33 MHz PMC slot not available with front I/O, hard disk EEPROM or flash drive mounted • 512 kbit serial EEPROMs for non-volatile user data IPMI 1.5 Floppy • Baseboard Management Controller supporting the Intelligent • One channel 3.5“ floppy drive controller Platform Management Interface (IPMI) architecture in • 720 KB and 1.44 MB compliance with PICMG 2.9 • Peripheral mode and BMC mode are supported Watchdog • Integrated in E7501/ICH4 chipset Timer • IRQ and integrated in E7501/ICH4 chipset Temp. Sensor Power Requirements • CPU die and heatsink temperature software readable from • +5 V, +3.3V, +12V Required –65°C to +127°C • -12V Only if required by mounted PMC module LED Power Consumption - typical operating current (* = estimated) • front panel LED System control (read) • w/o keyboard, hard disk, modules, measured at DOS prompt, no power savings. Hot-Swap - compliant to PICMG 2.1 • Peripheral mode: Board can be inserted or removed in a Pentium M 5 V 3.3 V total Power powered system 600 MHz, 256MB 0.7A 5.1A 20.3W • System controller mode: Other, non system (peripheral) boards 1.1 GHz, 512MB 1.5A 5.9A* 27.0W* can be removed or added with power on 1.6 GHz, 2GB 3.4A 7.5A* 41.8W* H.110 Friendly • w/o keyboard, hard disk, modules, Windows XP, 3D graphics • Versions with non populated J4 (see Front and Rear I/O table) do active. Both Gigabit Ethernet channels linked, CPU running at not interfere with H.110 bus on P4 instruction mix for maximum power consumption. BIOS Features Pentium M 5 V 3.3 V total Power • New AMI BIOS Core 8, in-system programmable Flash ROM 600 MHz, 256MB 0.9A 6.9A 27.3W • CPU, memory and IDE auto-detection/selection 1.1 GHz, 512MB 2.3A 7.7A* 36.9W* • Integrated VGA, and Ethernet BIOS ROM 1.6 GHz, 2GB 5.4A 9.3A* 57.7W* • USB Mass Storage support • Password protection, BIOS post, system and video BIOS shadowing Power Allowances - PMC slot • Extensive setup with remappable serial/parallel ports • +5 V, +3.3V: Total power max. 7.5 W • Diskless, keyboardless and videoless operation • ±12 V: • Remote BIOS through serial port Mechanical – PICMG 2.0 Software • 6U, 1 slot wide • The following software is supported to the extent listed below. • 233 x 160 x 20 mm (including flash drive) or hard disk OS On Request Planned Temperature WIN 2000 -✓• Highest reachable operating temperature depends on processor WIN XP -✓type, speed and ambient conditions (airflow) QNX 4 + 6 -✓• TMDS option may reduce temperature range VxWorks -✓• All values under typical conditions w/o PMC module, HDD or Lynx OS✓- flash drive Linux -✓ Operating Storage Front and Rear I/O (with transition module CTM12) Standard 0°C to +55°C –40°C to +85°C • The pinouts of the transition module connectors (rear I/O) Extended –40°C to +55°C –40°C to +85°C corresponds to standard PC connectors (press-fit cables). Humidity Rear Function Front J3/J4/J5 • Operating: 5 - 95% @ 40°C *1*5 DVID -✓• Storage: 5 - 95% @ 40°C *3 *1*5 VGA✓✓ *2*3 *2 Eth 1✓✓Altitude *2*3 *2 Eth 2✓✓• Operating: 15.000 ft. (4.5 km) Keyb+Mouse ✓✓ • Storage: 40.000 ft. (12 km) Reset ✓✓ LEDs ✓✓ Shock *5 USB 1-5 1 2-5 • C-, I-Style 12g / 6 ms, 3 axis, up & down, 5 hits / direction IDE primary onboard - IDE secondary -✓Vibration *5 Floppy -✓• C-, I-Style 2g rms @ 5 to 100 Hz, 30 minutes each axis COM 1-2 1 1,2 *5 LPT -✓MTBF PMC 1 ✓✓ • Calculations are available in accordance with MIL-HDBK-217. *4 PMC 2✓✓Please contact factory. *1 rear DVI-I connector for DVI and VGA *2 either front or rear as an order option Safety *3 32-bit/33 MHz PMC slot not available with this front I/O option • Designed to meet standard UL1950, CE class A, FCC-A *4 not with front VGA and/or Ethernet *5 not without J4 CT9 Block Diagram Ordering Information Hardware Accessories CTM12 I/O transition module for 6U backplane (IEEE 1101.11-1998 compliant) SC304F Floppy disk 3.5 inch, 19“ box: 3U/4HP, cable SC306HI10G0 IDE hard disk 3.5“, 10 GB, 19“ box: 3U/6HP, cable ZKAAPS2SPLIT Cable for keyboard and mouse on front panel Operating Systems Extensive operating systems support are available, see page 3 of this document. Chassis with power supplies, backplanes and drives on request. For detailed information and further options, contact SBS. Corporate Headquarters European Headquarters 2400 Louisiana Blvd. NE, #5-600 Memminger Str. 14 Albuquerque, NM 87110-4316 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2004 SBS Technologies, Inc. 20040108