ROHM MCR18EZHF1911

MCR18 Resistors Thick film rectangular MCR18 (3216 size: 1 / 4W) !Features 1) Power rating of 1 / 4W 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Leading the world in development and mass production. Since start of production in 1976 (first in the wold), this component has established a solid reputation as a general– purpose chip resistor. 5) ROHM resistors have approved ISO–9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it. !Ratings Item Conditions Specifications 0.25W (1 / 4W) Rated power Power must be derated according to the power derating curve in at 70°C Figure 1 when ambient temperature exceeds 70°C. 100 80 60 40 20 0 −55 0 70 100 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) Limiting element voltage 200V R: Nominal resistance (Ω) Nominal resistance See Table 1. −55°C to +155°C Operating temperature POWER LOAD (%) MCR18 Resistors Jumper type Table 1 Resistance Max. 50mΩ Resistance range Resistance temperature coefficient Resistance tolerance (Ω) (ppm / °C) Rated current 2A F (±1%) 0.1 ≤ R < 0.15 (E24) 400±200 Operating temperature −55°C to +155°C 0.15 ≤ R < 10 (E24) ±250 10 ≤ R ≤ 2.2M (E24,96) ±100 J (±5%) 0.1 ≤ R < 0.15 (E24) 400±200 0.15 ≤ R < 1 (E24) ±250 1.0 ≤ R < 2.2 (E24) 500±350 2.2 ≤ R < 10 (E24) ±500 10 ≤ R ≤ 10M (E24) ±200 !Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high–level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. !Characteristics Guaranteed value Item Test conditions (JIS C 5201-1) Resistor type Jumper type J : ±5% Max. 50mΩ JIS C 5201-1 4.5 Resistance F : ±1% Variation of resistance JIS C 5201-1 4.8 See Table.1 with temperature Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Overload ± (2.0%+0.1Ω) Max. 50mΩ Limiting Element Voltage×2 : 400V A new uniform coating of minimum of JIS C 5201-1 4.17 95% of the surface being immersed Rosin·Ethanol (25%WT) Solderability and no soldering damage. Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.18 Resistance to No remarkable abnormality on the appearance. Soldering condition : 260±5°C soldering heat Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.19 Rapid change of Test temp. : −55°C~+125°C 5cyc temperature ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 40°C, 93%RH Damp heat, steady state Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C Endurance at 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.3 155°C Endurance Test time : 1,000h~1,048h ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 Resistance to solvent 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.33 Bend strength of Without mechanical damage such as breaks. the end face plating 0 8 0 6 0 4 0 2 MCR18 Resistors !External dimensions (Units : mm) 1 2 No. 0.5±0.25 Material 1 Resistive element (Oxide metal thick film) 3 2 Silver palladium thick film electrode 0.5±0.25 3 Nickel electrode 4 3.2±0.15 4 Sn/Pb or Sn electrode 5 5 Alumina substrate 6 Overcoating (glass) 6 !Packaging Reel Taping P0 P2 P2 φD2 E F W B2 AB D A2 Heat crimp cover/Tape Thick paper (Underside paper tape) Chip resistor Square punchout hole mount T2 C (Units: mm) Label WF E A2 B2 EIAJ ET-7200A compliant +0.1 +0.15 1.95 3.5 8.0±0.3 3.5±0.05 1.75±0.1 −0.05 −0.05 (Units: mm) D2 P2 P2 P2 T2 +0.1 AB C D φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 0 0 +1.0 +1 φ180 φ60 9 φ13±0.2 −3 0 0 Bulk case Slider Shutter 12±0.1 0 36 −0.2 110±0.7 EIAJ ET-7201A compliant (Units: mm) 0 8 0 6 0 4 0 2 0.55±0.1 1.6±0.15 MCR18 Resistors !Makeup of the part number 3-digit or 4-digit IEC coding system Part No. Nominal resistance Packaging / Processing specifications Resistance tolerance Special part number Standard ordering F ±1% J ±5% 10Ω or more (F class) Part No. Code Packaging Blank unit(pcs) 1Ω or more (J class) Specify "J" for jumper also. MCR18 EZH Paper tape 5,000 Up to 10Ω (F class) PZHI Bulk case 5,000 L Up to 1Ω (J class) !Dimensions 3.45 1.80 0.75 JIS C 5201-1 4.4.2 JIS C 5201-1 4.4.2 JIS C 5201-1 4.4.2 3.40 SAMPLE SIZE : n=20pcs SAMPLE SIZE : n=20pcs SAMPLE SIZE : n=20pcs 1.75 0.70 MICROMETER MICROMETER MICROMETER 3.35 1.70 0.65 3.30 1.65 0.60 3.25 3.20 1.60 0.55 3.15 1.55 0.50 3.10 1.50 0.45 3.05 1.45 0.40 3.00 2.95 1.40 0.35 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.2 Dimensions (length) Fig.3 Dimensions (width) Fig.4 Dimensions (thickness) !Electrical characteristics 8.0 900 4.0 JIS C 5201-1 4.8 JIS C 5201-1 4.13 JIS C 5201-1 4.5 SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=20pcs 700 6.0 3.0 25°C / −55°C RATED VOLTAGE×2.5TIMES : 2s 20°C 65%RH 500 25°C / 125°C LIMITING ELEMENT VOLTAGE×2 : 400V 4.0 2.0 300 1.0 2.0 100 0.0 0.0 −100 −2.0 −1.0 −300 −4.0 −2.0 −500 −3.0 −6.0 −700 −4.0 −8.0 −900 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k1M 10M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.5 Resistance Fig.6 Variation resistance with Fig.7 Overload temperature DC RESISTANCE (%) LENGTH (mm) TEMPERATURE COEFFICIENT (ppm/°C) WIDTH (mm) ∆R/R (%) THICKNESS (mm) MCR18 Resistors 2.0 2.0 4.0 JIS C 5201-1 4.19 JIS C 5201-1 4.24 JIS C 5201-1 4.18 SAMPLE SIZE : n=10pcs 1.5 SAMPLE SIZE : n=10pcs 1.5 SAMPLE SIZE : n=10pcs 3.0 −55°C / 125°C 5cyc 40°C 93%RH WITH NO LOAD 1,000h SOLDERING CONDITION : 260°C 10s 1.0 1.0 2.0 0.5 0.5 1.0 0 0 0.0 −0.5 −0.5 −1.0 −1.0 −1.0 −2.0 −1.5 −1.5 −3.0 −2.0 −2.0 −4.0 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Resistance to soldering heat Fig.9 Rapid change of Fig.10 Damp heat, steady state temperature 4.0 4.0 2.0 JIS C 5201-1 4.25.1 JIS C 5201-1 4.25.3 JIS C 5201-1 4.29 SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs 3.0 3.0 SAMPLE SIZE : n=10pcs 1.5 70°C 1,000h 155°C WITH NO LOAD 1,000h IPA, 5min. OVERLOAD : THE RATED VOLTAGE 2.0 2.0 1.0 1.0 1.0 0.5 0 0 0.0 −1.0 −1.0 −0.5 −2.0 −2.0 −1.0 −3.0 −3.0 −1.5 −4.0 −4.0 −2.0 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.11 Endurance (at 70°C) Fig.12 Endurance Fig.13 Resistance to solvents 2.0 JIS C 5201-1 4.33 SAMPLE SIZE : n=10pcs 1.5 ENDURANCE WITH 90mm WIDTH 1.0 0.5 0 −0.5 −1.0 −1.5 −2.0 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.14 Bend strength of the end face plating RESISTANCE CHANGE (%) RESISTANCE CHANGE (%) RESISTANCE CHANGE (%) RESISTANCE CHANGE (%) ∆R/R (%) ∆R/R (%) RESISTANCE CHANGE (%)