ROHM MCR03EZPFX3740
Description
RES 374 OHM 1/10W 1% 0603 SMD
Part Number
MCR03EZPFX3740
Price
Request Quote
Manufacturer
ROHM
Lead Time
Request Quote
Category
PRODUCTS - M
Datasheet
Extracted Text
MCR03 Resistors Thick film rectangular resistors MCR03 (1608 size) zFeatures 1) Power rating of 1 /10W 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Resistors Absorbs impact, facilitates mounting. 5) ROHM resistors have approved ISO–9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. zRatings Item Conditions Specifications 0.10W (1 / 10W) Power must be derated according to the power derating curve in Rated power Figure 1 when ambient temperature exceeds 70°C. at 70°C 100 80 60 40 20 0 −55 0 70 100 125 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obstained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E : Rated voltage (V) E= P×R P : Rated power (W) R : Nominal resistance (Ω) Limiting element voltage 50V Nominal resistance See Table 1. Operating temperture −55°C to +155°C Rev.A 1/5 POWER LOAD (%) MCR03 Resistors Jumper type Table 1 Resistance tolerance Resistance range Resistance temperature coefficient Resistance Max.50mW (Ω) (ppm / °C) Rated current 1A 1.0 R 10 (E24) ±400 J (±5%) Operating temperature −55°C to +155°C 10 R 10M (E24) ±200 FX (±1%) 10 R 10M (E24,96) ±100 ±100 10 R 100 (E24,96) D (±0.5%) 100 R 1M (E24,96) ±50 zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. zCharacteristics Guaranteed value Item Test conditions (JIS C 5201-1) Resistor type Jumper type J : ±5% Max. 50mΩ JIS C 5201-1 4.5 Resistance F : ±1% D : ±0.5% JIS C 5201-1 4.8 Variation of resistance See Table 1 Max. 50mΩ with temperture Measurement : +25 / +125°C JIS C 5201-1 4.13 Overload ±(2.0%+0.1Ω) Max. 50mΩ Rated voltage(current) ×2.5, 2s. Limiting element voltage ×2 : 100V JIS C 5201-1 4.17 A new uniform coating of minimum of Rosin Ethanol (25%WT) 95% of the surface being immersed Solderability Soldering condition : 235V±5°C and no soldering damage. Duration of immersion : 2.0±0.5s. ±(1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.18 Resistance to Soldering condition : 260±5°C soldering heat No remarkable abnormality on the appearance. Duration of immersion : 10±1s. JIS C 5201-1 4.19 Rapid change of ±(1.0%+0.05Ω) Max. 50mΩ Test temp : −55°C to +125°C 5cyc temperature ±(3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 Damp heat, steady state 40°C, 93%RH Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1 ±(3.0%+0.1Ω) Max. 100mΩ Endurance 70°C Rated voltage (current), 70°C 1.5h : ON−0.5h : OFF Test time : 1,000h to 1,048h JIS C 5201-1 4.25.3 ±(3.0%+0.1Ω) Max. 100mΩ 155°C Endurence Test time : 1,000h to 1,048h ±(1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 Resistance to solvent 23±5°C, Immersion cleaning,5±0.5min. Solvent : 2-propanol JIS C 5201-1 4.33 ±(1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating Without mechanical damege such as breaks. Rev.A 2/5 0 8 0 6 0 4 0 2 MCR03 Resistors zExternal dimensions (Unit : mm) 1 No. Material 0.3±0.2 2 Thick dielectric glaze of oxide metal 1 (only silver used for jumper) 3 2 Thick film of silver for electrode 0.3±0.2 3 NIckel-coated electrode 4 1.6±0.1 4 External electrode coated with Sn 5 5 Alumina substrate 6 Overcoating 6 zPackaging Reel Taping P0 P2 P1 φD0 E F W B0 AB D A0 Heat crimp cover / Tape Thick paper (Underside paper tape) Chip resistor Square punchout hole mount T2 C Label (Unit : mm) EIAJ ET-7200B compliant WF E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 D0 P0 P1 P2 T2 +0.1 φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 0 (Unit : mm) AB C D 0 +1 +1.0 φ180 φ60 9 φ13±0.2 −1.5 0 0 Rev.A 3/5 0 8 0 6 0 4 0 2 0.45±0.1 0.8±0.1 MCR03 Resistors zPart designation 3-digit or 4-digit IEC coading system Part No. Nominal resistance Packing / Processing specifications Resistance tolerance Resistance temperature coefficient Part No. Code Packaging Standard orderingJX ±5% F ±1% D ±0.5% ±100(ppm/°C) unit(pcs) Specify "J" for jumper also. Blank See Table.1 MCR03 EZP Paper tape 5,000 zDimensions 1.80 1.00 0.65 JIS C 5201-1 4.4.2 JIS C 5201-1 4.4.2 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs SAMPLE SIZE : n=20pcs SAMPLE SIZE : n=20pcs 1.75 0.95 0.60 MICROMETER MICROMETER MICROMETER 1.70 0.90 0.55 1.65 0.85 0.50 1.60 0.80 0.45 1.55 0.75 0.40 1.50 0.70 0.35 1.45 0.65 0.30 1.40 0.60 0.25 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M RESISTANCE(Ω) RESISTANCE(Ω) RESISTANCE (Ω) Fig.2 Dimensions (length) Fig.3 Dimensions (width) Fig.4 Dimensions (thickness) zElectrical characteristics 900 6.0 5.0 JIS C 5201-1 4.8 JIS C 5201-1 4.5 JIS C 5201-1 4.13 4.0 700 SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=20pcs 25°C / −55°C 4.0 RATED VOLTAGE×2.5 20°C 65%RH 3.0 500 25°C / 125°C TIMES : 2s LIMITING ELEMENT VOLTAGE×2 : 100V 2.0 300 2.0 1.0 100 0 0 −100 −1.0 −2.0 −300 −2.0 −500 −3.0 −4.0 −700 −4.0 −900 −5.0 −6.0 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M RESISTANCE(Ω) RESISTANCE(Ω) RESISTANCE(Ω) Fig.6 Variation of resistance with Fig.5 Resistance Fig.7 Overload temperature Rev.A 4/5 LENGTH (mm) DC RESISTANCE (%) TEMPERATURE COEFICIENT (ppm/°C) WIDTH (mm) R / R (%) THICKNESS (mm) MCR03 Resistors 2.0 2.0 4.0 JIS C 5201-1 4.24 JIS C 5201-1 4.18 JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs 1.5 1.5 3.0 SOLDERING CONDITION : 260°C 10s −55°C / 125°C 5cyc. 40°C 93%RH WITH NO LOAD 1,000h 1.0 1.0 2.0 0.5 0.5 1.0 0 0 0 −0.5 −0.5 −1.0 −1.0 −1.0 −2.0 −1.5 −1.5 −3.0 −2.0 −2.0 −4.0 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M RESISTANCE(Ω) RESISTANCE(Ω) RESISTANCE(Ω) Fig.8 Resistance to soldering heat Fig.9 Rapid change of temperature Fig.10 Damp heat, steady state 2.0 4.0 2.0 JIS C 5201-1 4.25.1 JIS C 5201-1 4.25.3 JIS C 5201-1 4.29 SAMPLE SIZE : n=10pcs SAMPLE SIZE : n=10pcs 1.5 3.0 SAMPLE SIZE : n=10pcs 1.5 70°C 1,000h IPA, 5min. 155°C WITH NO LOAD 1,000h OVERLOAD : THE RATED VOLTAGE 1.0 2.0 1.0 0.5 1.0 0.5 0 0 0 −0.5 −1.0 −0.5 −1.0 −2.0 −1.0 −1.5 −3.0 −1.5 −2.0 −4.0 −2.0 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) RESISTANCE(Ω) RESISTANCE (Ω) Fig.11 Endurance at 70°C Fig.12 Endurance Fig.13 Resistance to solvents 2.0 JIS C 5201-1 4.33 1.5 SAMPLE SIZE : n=10pcs ENDURANCE WITH 90mm WIDTH 1.0 0.5 0 −0.5 −1.0 −1.5 −2.0 1 10 100 1k 10k 100k 1M 10M RESISTANCE(Ω) Fig.14 Bend strengh of the end face plating Rev.A 5/5 R / R (%) R / R (%) R / R (%) R / R (%) R / R (%) R / R(%) R / R (%) Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the MCR03EZPFX3740 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers





What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods