® Camera Link 5 mega-pixel Camera 5M Camera Link with highly rigid case FV-L500B1 and compact design 5 mega- Camera PoCL pixels Link Use in tasks such as fault inspection, display inspection, solder defect inspection, and high-precision flaw detection for semiconductors, liquid crystal and plasma flat panel displays, circuit boards, etc. 35 mm×35 mm compact design Uses PoCL (Power over Camera Link), which has a strong track record as a high-resolution digital camera interface High-speed frame rate of 5M: 16 fps Various trigger modes (pulse width, edge preset trigger) as standard features In addition to camera tripod screw holes, M4 screw holes are located on four sides (top, bottom, left, right) To increase mounting precision, mounting holes are arranged based on the CCD optical axis [Exposure-interval signal output] outputs the camera exposure interval and enables efficient inspection [Supported cameras] FV-L500B1, FV-L200B1, FV-L030B1, FV-G200B1, FV-G030B1 Trigger signal Exposure-interval signal output—which can start the next exposure during the Standard CCD exposure cameras transfer of the previous image—makes it possible to achieve high-speed work Camera image output inspection*, thereby raising inspection efficiency. In addition, since the camera exposure interval is output externally, it can be used for various purposes. Trigger signal Cameras supporting Limited to cases where the next exposure does not end before the completion of image transfer. * exposure-interval CCD exposure signal output Camera image output • Exposure starts during image transfer. The CCD exposure start marked with the is speeded up, thereby making high-speed work detection possible. Dimensions and rear connector specifications FV-L500B1 Product specifications ±0.02 17.69 +0.010 Imager 2/3" interline 5.0 Mega pixels monochrome progressive CCD 2.0 Depth 2.5 H7 0 ±0.05 15.5 ±0.05 14.5 22.7 Active picture elements 2448 (H) × 2058 (V) 4–M4 Depth 4 Cell size 3.45 (H) × 3.45 (V) µm Vertical frequency (Frame rate) 16 Hz (R1) 1/4”20UNC(Screw for Tripod) Horizontal frequency 33.264 kHz +0.010 φ2.0 Depth 2.5 H7 0 40.7 17.69 [CCD image area: in air 17.526] Pixel frequency 64 MHz 35 10.5 4-R3 0 B φ36−0.05 Minimum scene illumination 0.24 lux at F1.2 A Sync. System Internal Video output Digital 8 , 10 or 12 bit Raw Data (Base configuration) U1(C Mount Screw) Shutter speed OFF, 1/8 to 1/209,000 sec. (Variable at every H and clock) Unit: mm Gain 0 to 18.309 dB Camera Link connector 3M-made SDR equivalent A Gamma 1.0 Input/output signal connector B Hirose-made HR10A-7R-6PB equivalent Trigger signal input can be done in accordance with the Input voltage 12 Vdc ± 10% camera setting.Optional connector RICOH FP-CN6PB is supported. Power supply Note: For the frame grabber board and cable, the PoCL type should be used. Consumption Less than 4.0 W Voltage Signal IN/ Pin No. name OUT Low voltage High voltage Dimensions 35 (W) × 35 (H) × 40.7 (D) mm (excluding the connector) 1 GND IN 0V IN 0 to +0.99V +2.3 to +3.3V Lens mount C mount 2 I/O-1 IN/OUT OUT 0V +3.3V IN 0 to +0.99V +2.3 to +3.3V Weight Approximately 80 g 3 I/O-2 IN/OUT OUT 0V +3.3V IN 0 to +0.99V +2.3 to +3.3V Operational -5 to 40 deg. C 4 I/O-3 IN/OUT temperature Operational OUT 0V +3.3V environment Storage 5 TRIGGER OUT OUT 0V +3.3V -30 to 65 deg. C temperature 6 N.C. 04 4575 Ruffner St., San Diego, CA 92111 | P: 858.565.1101 | T: 800.284.2288 | F: 858.565.7845 | sales@avsupply.com | www.avsupply.com 35 ±0.05 25 ±0.05 16.8 ±0.02 15 φ30 2.3