HSS1/HSS2 ® High-Security SECURITY SYSTEM COMPONENTS Intercom Stations HSS13/HSS8 Call-In Switches TRI-GARD TRIPLE BARRIER SPEAKER PROTECTION Vandal-proof design HSS1 1 with call button An initial metal plate with offset perforations protects against direct penetration. . . 2 A second and a third metal plate are further barriers against vandalism as well as flame or liquid damage. . . HSS2 less call button FEATURES • Heavy-Gauge Stainless Steel Construction • Weather Resistant Speaker • Vandal-Proof Speaker Mounting Design 3 • Water-Resistant Tamper-Proof Call Switch (HSS1) A final metal enclosure defies tam- • Standard 3-Gang Electrical Box Mount pering, and enhances audio fre- • Integrates With All Rauland Communications Systems quency response HSS1/HSS2 SPECIFICATIONS SPL Output: 400 Hz to 4 KHz, +3dB @25V Switch: SPST normally open .25 watt tap—81dB @ 1 KHz Speaker Transformer Terminations: Color-coded pre-wired pigtails 0.5 watt tap—84dB @ 1 KHz Call Switch Terminations: Screw terminals 1.0 watt tap—87dB @ 1 KHz 2.0 watt tap—90dB @ 1 KHz Size: 7-1/2" (19.05 cm) long, 5-1/2" (13.97 cm) high, 4.0 watt tap—93dB @ 1 KHz 2-1/4" (5.71 cm) deep Speaker/Microphone: 3" acrylic impregnated cotton cloth cone Weight: 2-1/2" lbs. (1.13 kg) speaker.Waterproof and puncture-resistantconstruction. 2.5 ounce Wiring Requirements: 3-conductor shielded ceramic magnet. 8-ohm voice coil. With 25V matching transformer tapped at 1/4, 1/2, 1, 2 @ 4 watts Recommended Backbox: Steel City 3G three-gang backbox with 3GC plaster ring or GW335-C masonry Microphone Output: 74dB SPL @ 1 KHz, 2.5 mV 0.25 watt tap type, or equal (U.L. recognized) 1.9 mV 0.5 watt tap 1.4 mV 1.0 watt tap Associated Equipment: All Rauland Communications Systems 1.1 mV 2.0 watt tap stations do not include mounting hardware. 0.9 mV 4.0 watt tap (over) 8/97 HSS1/2/13/8 HSS1/HSS2 ® High-Security SECURITY SYSTEM COMPONENTS Intercom Stations HSS13/HSS8 Call-In Switches DESCRIPTION The Rauland HSS1 and HSS2 High-Security Stations are duty construction. A rugged steel actuator activates a designed to provide two-way intercom functions in facilities momentary switch whose movement is limited by a such as correctional institutions or wherever vandalism is mechanical stop to prevent damage caused by attempted likely to be encountered. The stations interface readily with vandalism or heavy impact. The call-in switch is normally all Rauland Intercom Systems. open; the self-cleaning contacts are rated in excess of 350 Two-way communications are accomplished through the watts @ 120V AC (non-inductive loads). use of the built-in speaker/microphone. A call origination The speaker/microphone used in the stations is switch is provided in the HSS1 station. an acrylic impregnated cotton cloth cone speaker, inge- The Rauland HSS2 High-Security Station is identical to niously protected against tampering or damage caused by the HSS1 but does not have a call origination switch. It can- flame or liquids. The speaker is mounted internally to the not initiate a call, but it can respond to a call through the last of three protective metal “barrier” plates which effec- built-in speaker/microphone. tively deny access to the speaker cone. All speaker trans- The HSS1 and HSS2 are virtually indestructible. They former terminations are accomplished by pigtail leads. The are protected externally by an 11-gauge stainless steel face call switch terminations are screw terminals. The stations plate with a mar-resistant brushed finish. The call switch are designed for flush mounting in a standard three-gang assembly of the HSS1 is a momentary push-button type, electrical box. water-resistant, vandal-proof both in design and heavy- HSS13/HSS8 HIGH-SECURITY AND EMERGENCY CALL-IN SWITCHES FEATURES • Virtually Indestructible • 11-Gauge Stainless Steel Faceplate • Tamper-Proof Switch • Steel Activator Button (HSS13) Red “Mushroom” Button (HSS8) Single-Gang Backbox Mount HSS13 HSS8 High-Security High-Security Switch Emergency Switch SPECIFICATIONS Switch Type: SPST normally open Weight: 1.7 lbs. (.77 kg) Steel Actuator Button (HSS13) Wiring Requirements: 2 conductors Red “Mushroom” Button (HSS8) Recommended Backbox: Raco 674 Single-gang Terminations: Color-coded pre-wired pigtails (HSS8) (U.L. recognized) Screw Terminals: (HSS13) Associated Equipment: Size: 5-1/2" (13.97 cm) high, 3-1/2" (8.89 cm) wide, All Rauland Communications Systems 2" (5.08 cm) deep DESCRIPTON The Rauland HSS13 High-Security Call-In Switch is vent damage caused by attempted vandalism. intended for call origination where the speaker/ The HSS8 Emergency Call-In Switch is identical to the microphone is not used or is located remotely, i.e. in ceil- HSS13, but incorporates a unique red metal “mushroom” ing or high on wall. For use in cells, at door locations or call-in button which actuates with minimum pressure to wherever call origination is desired. meet the ADA recommendations. A rugged steel actuator activates a momentary switch Unit mounts in standard single-gang backbox; with whose movement is limited by a mechanical stop to pre- tamper-proof hardware. (Not provided) Specifications subject to change without notice. RAULAND-BORG CORPORATION 3450 West Oakton Street, Skokie, Illinois 60076-2958 • Tel: (847) 679-0900 • FAX: (847) 679-0625 In Canada: RAULAND-BORG (CANADA) INC. • 6535 Millcreek Drive, Unit 5, Mississauga, Ontario, Canada L5N 2M2 • (905) 821-2225 • FAX: (905) 821-8325 HSS1/2/13/8 © Copyright 1995 Rauland-Borg Corporation • Printed in USA 8/97