RAD EGATE-20/AC/T1

Description
RAD EGATE-20/AC/T1 Gateway - ETHERNET OVER E1/T1 GATEWAY, AC, T1 PORTS
Part Number
EGATE-20/AC/T1
Price
Request Quote
Manufacturer
RAD
Lead Time
Request Quote
Category
PRODUCTS - E
Specifications
Connector
9-pin, D-type, female
Data Rate
9.6, 19.2, 115.2 kbps
Diagnostics
E1: Remote loopback; T1: Remote and FDL loopbacks
Remote and FDL loopbacks
Dimensions (HxWxD)
43.7 mm (1.7 in/1U) x 215.9 mm (8.5 in) x 300.0 mm (11.8 in)
E1 Interface Compliance
G.703; G.704
E1 Interface Connector
RJ-45 (balanced); Coaxial (unbalanced)
E1 Interface Data Rate
2.048 Mbps
E1 Interface Number of Ports
8
Ethernet Compliance
10/100BaseT, conforms to the relevant sections of IEEE 802.3 and 802.3u, 802.1p, and 802.1Q
Ethernet Connector
RJ-45
Ethernet Data Rate
100 Mbps
Ethernet Number of Ports
4
Filtering and Forwarding
Transparent or filter at wire-speed
Framing
D4, ESF (framed)
Framed/unframed
Humidity
Up to 90%, non-condensing
Indicators
PWR (green)–Power status; RDY (green)–Ready indicator; ALM (red)–Alarm status
Interface
RS-232/V.24 (DCE asynchronous)
LAN Table
Up to 2,048 MAC addresses (learned)
Line Code
B8ZS
Line Coding
HDB3
Line Impedance
100O (balanced)
120O (balanced); 75O (unbalanced)
Max. Frame Size
1600 bytes
Operation Modes
VLAN-aware, VLAN-unaware
Power
AC:100 to 240 VAC (±10%), 50 to 60 Hz; DC:-48 VDC nominal
Power Consumption
9W max
Supported Modes
Autonegotiation, full/half duplex, flow control
T1 Interface Compliance
ANSI T1.403
T1 Interface Connector
RJ-45
T1 Interface Data Rate
1.544 Mbps
T1 Interface Number of Ports
8
Temperature
0°–50°C (32°–122°F)
WAN PROTOCOL
Type:HDLC (native HDLC compatible with RAD products)
Weight
2.2 kg (4.7 lb)
Datasheet
Extracted Text
Data Sheet Egate-20 Channelized Ethernet Gateway Flexible Ethernet aggregation of Fast Ethernet to eight fully channelized E1 or T1 circuits • Transparent Ethernet services in point-to-point and point-to-multipoint topologies by utilizing VLAN tagging, stacking and switching • Efficient utilization of WAN interface at wire-speed Up to 248 or 192 • Equipment and maintenance costs lower than other alternatives • Four-level QoS according to 802.1p, DSCP, IP Precedence and per port remote LANs over fractional E1 or T1 Egate-20 is a channelized Ethernet Together with service scalability, small gateway for interconnecting PDH and footprint, and low power consumption, channels packet-based networks. Egate-20 significantly reduces equipment cost and simplifies network operation. The Ethernet gateway aggregates and switches Ethernet traffic into eight Deployed at a central location channelized E1 or T1 circuits, each (see Figure 1), Egate-20 aggregates user supporting up to 248 or 192 Ethernet Ethernet traffic received from remote channels (248 over E1 or 192 over T1). devices, such as RAD’s RICi-E1/T1, FCD, The traffic is combined into channelized and ASMi, thus completing a full access E1 or T1 streams, and handed over to the solution from the service provider central PSN via the unit's Fast Ethernet ports. site to the customer premises. Egate-20 replaces current high-priced Typical applications include: solutions, such as channelized n × E1/T1 • Ethernet private E-line/E-LAN services routers or multibox solutions based on • Aggregation of Ethernet traffic over cross-connects and switches. PDH wireless links • Network management backhauling. Innovative Access Solutions Egate-20 Channelized Ethernet Gateway BRIDGE In a typical service provisioning structure • Statistics and alarms for the physical (see Figure 2), Egate-20 links between E1/T1 and Ethernet interfaces, and for Using Egate-20 as a bridge in an users connected to the packet-switched the internal bridge. SDH/SONET environment, service providers network, and users connected to the TDM achieve seamless interconnection between MANAGEMENT network. Virtual channels are established customers utilizing different networks Egate-20 can be managed using different between the far-end users by tagging (TDM and packet-based), while ports and applications: separate user traffic channels with VLANs maintaining the same service level (B, C and D). These virtual channels • Local out-of-band management via an attributes. transparently forward all user traffic. In ASCII terminal connected to the The bridge filters and forwards traffic at addition, all devices are managed over the RS-232 port wire-speed, enabling full utilization of the VLAN A management channel, which • Remote out-of-band management via high-priced WAN circuit. enables secure separation between user one of the four 10/100BaseT ports VLAN tagging, stacking and striping at traffic and management traffic. • Remote inband management via one ingress and egress enable transporting QUALITY OF SERVICE (QoS) of the four Ethernet ports, performed user traffic transparently while keeping all Egate-20 provides differentiated services using Telnet, Web browser or RADview, user VLAN settings intact. In addition, the on the same link according to Ethernet or RAD's SNMP-based element management traffic may be tagged as a IP marking. Classification is based on management system. different VLAN, fully separating user traffic 802.1p, IP Precedence, DSCP or per port, from management data. Software upgrades and configuration files while the traffic is forwarded by four strict can be downloaded to Egate-20 via TFTP In VLAN-aware mode (IVL), frames are priority queues. or XMODEM. forwarded according to VLAN tags and PROTOCOLS MAC address. A dedicated VLAN tunnel is used to secure Egate-20 utilizes native HDLC for the management traffic and to separate it This allows defining different user traffic encapsulating Ethernet traffic over E1/T1 from user traffic. domains to create point-to-point (E-Line) circuits. or point-to-multipoint (E-LAN) topologies. Access to the unit's management DIAGNOSTICS AND STATISTICS A VLAN tunnel can be created for software is password-protected. The unit separating management and user traffic. Comprehensive diagnostic and can be managed by and report to up to performance monitoring capabilities 16 different managers simultaneously. Each bridge port switches and filters any include: This enables viewing the network status number of VLANs. This enables each and managing the unit from different remote location to be part of numerous • Ping and trace route for IP connectivity locations. VLAN domains. checks Figure 1. Aggregating Ethernet over E1/T1 Traffic Data Sheet Compliance Data Rate Specifications ANSI T1.403 100 Mbps E1 INTERFACE Data Rate Max. Frame Size 1.544 Mbps 1600 bytes Number of Ports 8 Line Code Supported Modes B8ZS Autonegotiation, full/half duplex, flow Compliance control G.703 Framing G.704 D4, ESF (framed) Connector RJ-45 Framing Line Impedance Framed/unframed 100Ω (balanced) WAN PROTOCOL Data Rate Diagnostics Type 2.048 Mbps Remote and FDL loopbacks HDLC (native HDLC compatible with RAD Line Coding Connector products) HDB3 RJ-45 INTERNAL BRIDGE Line Impedance FAST ETHERNET INTERFACE 120Ω (balanced) LAN Table 75Ω (unbalanced) Number of Ports Up to 2,048 MAC addresses (learned) 4 Connector Operation Modes RJ-45 (balanced) Compliance VLAN-aware, VLAN-unaware Coaxial (unbalanced) 10/100BaseT, conforms to the relevant Filtering and Forwarding sections of IEEE 802.3 and 802.3u, Transparent or filter at wire-speed T1 INTERFACE 802.1p, and 802.1Q Number of Ports 8 Figure 2. VLAN-Based Service Provisioning over Packet and TDM Networks 406-100-04/09 Specifications are subject to change without prior notice. © 2005–2009 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven, and the product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders. Data Sheet Egate-20 Channelized Ethernet Gateway CONTROL PORT E1U Unbalanced E1 port OPTIONAL ACCESSORIES T1 T1 port RM-35/@ Interface Note: Unbalanced E1 interface is provided via an Hardware kit for mounting one or two RS-232/V.24 (DCE asynchronous) adapter cable (CBL-RJ45/2BNC/E1, see Supplied Egate-20 units into a 19-inch rack Data Rate Accessories). @ Rack mounting kit 9.6, 19.2, 115.2 kbps SUPPLIED ACCESSORIES (Default = both kits): Connector AC power cord P1 Mounting one unit 9-pin, D-type, female DC adapter plug P2 Mounting two units GENERAL WM-35 CBL-RJ45/2BNC/E1 A hardware kit for mounting one Indicators Interface adapter for converting a Egate-20 unit on a wall PWR (green) – Power status balanced E1 RJ-45 connector to a pair of RDY (green) – Ready indicator CBL-DB9F-DB9M-STR BNC unbalanced coaxial connectors (if an ALM (red) – Alarm status DB-9 to DB-9 control port cable unbalanced E1 interface is ordered) Diagnostics E1: Remote loopback Product Comparison Table T1: Remote and FDL loopbacks Egate-100 RICi-E1, RICi-T1 Egate-20 Power (Ver. 3.0) (Ver 2.1) (Ver. 1.1) AC: 100 to 240 VAC (±10%), 50 to 60 Hz DC: -48 VDC nominal Feature Power Consumption Protocol type HDLC HDLC HDLC 9W max GFP (ITU-T G.8040) HDLC IS Environment PPP/BCP (RFC 1661, GFP (G.8040, Temperature: 0°–50°C (32°–122°F) RFC 3518) G.7041/Y.1303) Humidity: Up to 90%, non-condensing MLPPP (BCP) as per RFC 1661, RFC 1990, Physical RFC 3518 Height: 43.7 mm (1.7 in / 1U) Width: 215.9 mm (8.5 in) MAC address table 64000 1024 2048 Depth: 300.0 mm (11.8 in) QoS 802.1p 802.1p 802.1p Weight: 2.2 kg (4.7 lb) DSCP IP precedence DSCP IP precedence IP precedence Per port Ordering QoS mechanism Strict Strict Strict Egate-20/C/$ Number of queues 4 4 4 Legend Hot-swappable Yes No No C Interface: power supplies CH Channelized Host VLAN Yes Yes Yes $ Port: E1 Balanced E1 port VLAN tagging and Yes Yes Yes stacking International Headquarters North America Headquarters 24 Raoul Wallenberg Street 900 Corporate Drive Tel Aviv 69719, Israel Mahwah, NJ 07430, USA Tel. 972-3-6458181 Tel. 201-5291100 Fax 972-3-6498250, 6474436 Toll free 1-800-4447234 E-mail market@rad.com Fax 201-5295777 E-mail market@rad.com The Access Company www.rad.com Order this publication by Catalog No. 803596
Frequently asked questions
What makes Elite.Parts unique?

What kind of warranty will the EGATE-20/AC/T1 have?

Which carriers does Elite.Parts work with?

Will Elite.Parts sell to me even though I live outside the USA?

I have a preferred payment method. Will Elite.Parts accept it?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods