Guardian 5000 SafetyAnalyzer USES: AC/DC/IR/GC Electrical Safety Analyzer • Production and Compliance Testing of Appliances, Instruments and Introduction Information Technology Equipment in The Guardian 5000 is four instruments in one providing AC Hipot, DC Hipot, Accordance with UL, CSA, IEC, TUV Insulation Resistance, and Ground Bond measurements from a single test connector and Other Standards such as in one versatile instrument. This provides a cost effective solution to electrical safe- EN60335, EN60950, EN61010, CSA ty compliance testing with maximum flexibility for present and future requirements. C22.2 No. 1010.1, UL3111 and Performing all of the electrical safety tests in one box can reduce test time, increase UL1950 productivity and reduce the number of boxes requiring calibration. • Transformer Electrical Safety Testing Description • Electric Motor Safety Testing • Power Supply Safety Testing The Guardian 5000 AC Hipot Tester performs AC dielectric testing (hipot) over the voltage range from 100V to 5000VAC RMS. The maximum leakage current of 40mA • Verification of the Ground Connection RMS makes the Guardian 5000 ideal for testing devices with high leakage currents on Products with a Three Prong Power such as power supplies which have large filter or “Y” capacitors for noise reduction. Cord Both the actual test voltage and total current are displayed during testing. FEATURES: The Guardian 5000 DC Hipot Tester voltage range for DC dielectric testing is 100V • Programmable output voltage to 5KV to 6000VDC with a resolution of 10V. The maximum current leakage is 20mA AC and 6KV DC which allows quick charging of capacitive devices. A quick discharge of the device • Ground Bond Testing to 30A AC with when the measurement is complete, also minimizes test times. Adjustable Limit The Guardian 5000 Insulation Resistance measurements are similar to a DC hipot • Multi-point Scanner Option for High but rather than displaying leakage current, resistance is calculated and displayed. The Voltage Switching of up to 64 Points insulation resistance can be measured over the range of 10MW to 10GW with test • Programmable Ramp and Test Times voltages from 50VDC to 1000VDC in 1V steps. • Storage of 50 Tests Setups with 15 The Guardian 5000 Ground Bond provides up to 30A AC for ground bond testing. Steps per Setup The test current can be programmed from 1A to 30A in 0.1A steps. Hi current limit, • Trip Current Programmable to 40mA test time, frequency and open circuit no load voltage can all be programmed. The AC and 20mA DC offset feature can automatically compensate for any lead resistance. • Front Panel Lockout via Password • Standard IEEE and Remote Control Interfaces • Optional RS232 Interface For more detailed ® • LabVIEW Intrument Driver specifications, visit Software www.quadtech.com • Insulation Resistance Measurements from 10MW W to 10GW W 1ohm Limit For more information about special purchase, rent & lease options, call 1-800-253-1230 Fax 1-978-461-4295 Intl. 1-978-461-2100 HIPOT • LCR METERS • MEGOHMMETERS • MILLIOHMMETERS Guardian 5000 Display: +/-(1% of setting + 0.3A ) AC Output Voltage: Frequency: 50 or 60Hz Selectable Range: 100V to 5000V AC Resolution: 10 Volts / step No Load Voltage: 6 to 15 V programmable Frequency: 50/60 Hz selectable Resistance: Range: 0 - 500.0mV, 4 digits Waveform: Sinusoidal Accuracy: +/- (1% of reading + 3 cnts) Regulation: +/-(1% of setting +5V) Hi Limit: 10 mV to 510 mV Voltage Display: Accuracy: +/-(1% of reading + 5V) Offset Function: 0 to 100 mV, user selectable Resolution: 1Volt Test Time: 0.5 - 999sec(+/-20ms) AC Current Display: Total current Range: 0.001 to 40mA AC Common Features Resolution: 0.001mA AC/DC Test Time: Ramp: 0.1 to 99.9s (+/- 20ms) Accuracy:+/-(1.5% of reading + 5cnt) Test: 0.1 to 999s (+/- 20ms) and High/Low Limit Test: 1mA to 40mA AC Continuous Accuracy: +/-(1% of limit +1mA) Remote Control: Inputs: Start,Stop Low limit can be turned OFF Characteristics: Optically Isolated with ArcDetection: Arc Level: >1mA to 40 mA & OFF in +24V Active Low, Pulse Width >1ms. 0.001mA / Step Outputs: Pass/Fail/Under Test Characteristics: Dry Contact relay DC Output Voltage Ele. Characteristics: 120V 100mA max. Range: 100V to 6000V DC Logic: Closed if True Resolution: 10Volts / step Connect: Terminal Strip & 9 pin D Serie Regulation: +/-(1% of setting +5V) Test Setups: 50 Test Setups with 15 Steps each Voltage Display: Accuracy: +/-(1% of reading + 5V) Connectors: Front Connection and Rear Resolution: 1Volt Connections DC Current Display: Range:1mA to 20mA DC Front Panel Lockout: Password Resolution: 0.001mA Safety Features: Fast Cutoff (<0.4ms) and Fast Accuracy:+/-(1% of reading + 5cnt) Discharge High/Low Limit Test: 0.001mA to 20mA DC Miscellaneous: Continuous Voltage on Fail Low limit can be turned OFF Scanner Delay: 0.1 to 99.9, 0.1s/step Arc Detection: Arc Level: >1mA to 40 mA & OFF in Indication: Pass/Fail lights, audible sound 0.001mA / Step Buzzer Level: 1,2,3 and Off Insulation Resistance Standard Interface: IEEE488 Range: 10MW - 10GW Optional Interface: RS232 Accuracy: +/- 5% >= 500V 10MW - 1GW Data Bits: 8, Parity: None, Stop Bits: 1 +/-15% > 500V, 1GW - 10GW Default Baud Rate: 9.6k +/-10% < 500V, 1MW - 200MW EOS: CR + LF, Echo: Off +/- 15% < 200V, 200MW - 1GW Dimensions: (w x h x d):17 x 6.8 x 17.7in Voltage Range: 50V to 1000V DC (430 x 175 x 450mm) Voltage Accuracy: +/-(1% of setting +5V) Weight: 53 lbs (24kg), Net High/Low Limit Test: 10MW - 10GW 60 lbs (27kg), Ship High limit can be turned OFF Environmental: Operating: 0° to + 4°C IR Test Delay: 0.3 to 99.9 seconds programmable in Humidity: <75% 0.1 second steps Storage: - 10° to + 60°C Ground Bond Power: • 90 - 130V AC • 50 or 60Hz • 200 - 250V AC • 300W max Output Current: Range: 1.0 to 30.0A AC, setting 0.1A / step Ordering Information S05 Foot Switch G14 Power Entry Adapter Guardian 5000 Electrical Safety Optional Accessories: S06 High Voltage Probe G15 GC Lead Set, high &low Analyzer Calibration Data S10 HV Lead, 2 meters, unterminated G16 International Power Strip 5000-01 Scanner, 8 Channel HV Includes: S11 Gun Probe with remote start G22 Rear Panel Connection (factory 5000-02 Scanner, 8 Channel HV/4GC 150206 Instruction Manual S12 Load Box, resistive installed) 5000-03 Scanner, 8 Channel HV Rack 700070 Power Cable S14 Load Box, custom resistors G23 Rack Mount Ears Mountable S02 Test Leads S08 Gun Probe G25 Corded Product Adapter (240V) 5000-04 Scanner, 8 Channel HV/4GC G15 Ground Continuity Lead Set S09 HV Lead, 1 meter, unterminated G26 RS232 Interface Rack Mountable Calibration Certificate Traceable to NIST G13 Corded Product Adapter S04 HV Lead Set, 2m For more detailed specifications, visit www.quadtech.com For more information about special purchase, rent & lease options, call 1-800-253-1230 • Fax 1-978-461-4295 • Intl. 1-978-461-2100 5 Clock Tower Place, 210 East, Maynard MA 01754 P/N 030072/A2