90-105 WATT MEDICAL & ITE POWER SUPPLIES DESCRIPTION PMP105 SERIES (LVD) The PMP105 series of AC/DC switching power supplies are for 90-105 watts of continuous output power. They are enclosed in ����� a 94V-1 rated polyphenylene-oxide case with an IEC320/C14 or IEC320/C18 inlet to mate with interchangeable cord for world-wide use. All models meet EN55011, EN55022 and FCC class B emission limits, and are designed for medical and ITE applications, not for life-supporting equipment. FEATURES z Low safety ground leakage current z Both Class I and Class II models are certified to medical and ITE safety standards. SAFETY STANDARD APPROVALS z Wide input range 90 to 264 VAC UL ES 60601-1, CSA C22.2 No. 60601-1 z Optional output connectors File No. E178020 z 100% burn-in at full load z Overvoltage protection TÜV EN 60601-1 z Overcurrent protection z Compliant with CEC and Energy Star Efficiency level V requirements UL 60950-1, CSA-C22.2 No. 60950-1 * No load power consumption less than 0.5 W * Average active efficiency greater than 87% TÜV EN 60950-1 z Compliant with RoHS requirements INPUT SPECIFICATIONS GENERAL SPECIFICATIONS Input voltage: 90-264 VAC Switching frequency: 70-140 KHz Input frequency: 47-63 Hz Power factor: 0.98 Typical at 115 VAC Input current: 1.4 A (rms) for 115 VAC Efficiency: 87% min. at full load 0.7 A (rms) for 230 VAC Hold-up time: 10 ms minimum at 110 VAC Earth leakage current: 200 ȝA max. @ 264 VAC, 63 Hz Line regulation: ±0.5% maximum at full load Touch current: 100�ȝA max. @ 264 VAC, 63 Hz Inrush current: 80 A @ 115 VAC or 120 A @ 230 VAC, at 25� cold start Withstand voltage: 5600 VDC from input to output, 2100 VDC from input to ground, OUTPUT SPECIFICATIONS 700 VDC from output to ground Output voltage /current: See rating chart. (To verify AC strength, get correct test method to avoid power supply damage.) Maximum output power: See rating chart. For Class II models, 4000 VAC from input to Ripple and noise: 1% peak to peak maximum at the full output load MTBF: 150,000 hours at full load at 25� ambient, Overvoltage protection: Provided and set at 115-140% of its calculated per MIL-HDBK-217F nominal output voltage EMC Performance (IEC60601-1-2) Overcurrent protection: Protected to short circuit conditions EN55011/EN55022: Class B conducted, class B radiated Temperature coefficient: ±0.04% /� maximum FCC: Class B conducted, class B radiated Transient response: Maximum excursion of 4% or better on VCCI: Class B conducted, class B radiated all models, recovering to 1% of final EN61000-3-2: Harmonic distortion, class A and D value within 500 us after a 25% step EN61000-3-3: Line flicker load change EN61000-4-2: ESD, ±8 KV air and ±6 KV contact EN61000-4-3: Radiated immunity, 3 V/m ENVIRONMENTAL SPECIFICATIONS EN61000-4-4: Fast transient/burst, ±2 KV Operating temperature: 0� to +60� EN61000-4-5: Surge, ±1 KV diff., ±2 KV com. Storage temperature: -40� to +85� EN61000-4-6: Conducted immunity, 3 Vrms Relative humidity: 5% to 95% non-condensing EN61000-4-8: Magnetic field immunity, 3 A/m Derating: Derate from 100% at +40� linearly to EN61000-4-11: Voltage dip immunity, 30% reduction for 500 50% at +60� ms, 60% reduction for 100 ms and >95% reduction for 10 ms 49 UNIVERSAL INPUT PMP105 MEDICAL & ITE SERIES OUTPUT VOLTAGE/CURRENT RATING CHART (1) Model Output Average Active Min. Max. Peak Ripple & Efficiency (typical) (2) (3) Class I Class II Vnom. Current Current Current Tol. Noise Max. Power @ 115 / 230 Vac 12 V 0 A 7.50 A 15.0 A ±5% 120 mV 90 W 87 /87% PMP105-12 PMP105F-12 13 V 0 A 6.93 A 13.8 A ±5% 130 mV 90 W 87 /87% PMP105-12-1 PMP105F-12-1 PMP105-13 PMP105F-13 14 V-16 V 0 A 6.79 A 13.58 A ±5% 150 mV 95 W 87 /88% PMP105-13-1 PMP105F-13-1 18 V-19 V 0 A 5.84 A 11.6 A ±5% 180 mV 105 W 88 /88% 20 V-21 V 0 A 5.25 A 10.5 A ±5% 200 mV 105 W 88 /89% PMP105-13-3 PMP105F-13-3 24 V-25 V 0 A 4.38 A 8.7 A ±5% 240 mV 105 W 88 /89% PMP105-14 PMP105F-14 PMP105-15 PMP105F-15 28 V-29 V 0 A 3.75 A 4.5 A ±5% 280 mV 105 W 88 /89% PMP105-16 PMP105F-16 30 V-32 V 0 A 3.50 A 4.2 A ±5% 300 mV 105 W 88 /89% 36 V-38 V 0 A 2.92 A 3.5 A ±5% 360 mV 105 W 89 /90% PMP105-17 PMP105F-17 46 V-50 V 0 A 2.29 A 2.7 A ±5% 480 mV 105 W PMP105-18 PMP105F-18 90 /91% NOTES: 1. Class I models are equipped with IEC320/C14 inlet, and class II models with IEC320/C18 inlet. 2. For 10 seconds maximum, average power not to exceed maximum power rating. 3. Ripple and noise is maximum peak to peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10�ȝF tantalum capacitor in parallel with a 0.1 ȝF ceramic capacitor across the output. MECHANICAL SPECIFICATIONS OUTPUT POWER DERATING CURVE NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 681 grams (1.505 lbs.) approx. 4. Refer to Section titled ““OPTIONAL OUTPUT CONNECTORS””. Add the suffix assigned for a selected connector to a wanted model number, e.g. PMP105-14-B1, for ordering. 5. The length of output cable for PMP105-12, PMP105-12-1, and PMP105-13 is 37.4 (950) PIN CHART PIN 1 2 3 4 MODEL PMP105-12 PMP105F-12 PMP105-12-1 PMP105F-12-1 PMP105-13 PMP105F-13 PMP105-13-1 PMP105F-13-1 PMP105-13-3 PMP105F-13-3 V1 Return +V1 V1 Return +V1 PMP105-14 PMP105F-14 PMP105-15 PMP105F-15 PMP105-16 PMP105F-16 PMP105-17 PMP105F-17 PMP105-18 PMP105F-18 50