587B051 thru Only One Name Means ProTek’Tion™ 587B301 120V AC POWER LINE SURGE SUPPRESSOR APPLICATIONS ✔ Hard Wired Equipment AC Power Protection ✔ Load Side Distribution Systems ✔ Secondary Protection for Light Industrial AC Power IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-5 (Surge): 1kA, 8/20µs - Level 4(Line-Line) & 333A Level 4(Line-Ground) FEATURES U.S PATENT 4,563,720 ✔ Meets ANSI/IEEE C62.41 Requirements ✔ Listed to CSA, File LR65240 ✔ Differential and Common Mode Protection FIGURE 1 TRANSIENT VOLTAGE THREAT ✔ Low Clamping Voltage CONDITION ✔ Nanosecond Response Time 8 ✔ Long Life and Maintenance Free 6 MECHANICAL CHARACTERISTICS 4 ✔ Plastic Package 2 ✔ Weight: 485 Grams (Approximate) 0 ✔ Flammability Rating UL 94V-0 0 10 20 30 40 50 60 ✔ Device Marking: Part Number, Date Code, Logo, Voltage and Current Rating Time - µs DESCRIPTION FIGURE 2 TYPICAL CLAMPING ACTION OF A 16 AMP MODULE The 587B Series of 120 Volt AC Surge Suppressors is designed for use by the OEM, 6 equipment installer and or maintenance contractor. These modules employ a three stage technology proven to be the most cost effective and reliable method in protect- 4 ing sensitive electronic equipment from over voltage transients. 2 This series is designed to protect AC powered equipment from the 6,000 Volt peak 0 open circuit voltage and 3,000 Amp short circuit current as defined in ANSI/IEEE C62.41, Category C1. 0 10 20 30 40 50 60 Time - µs The 587B Series offers a high degree of protection against 120 VAC EMI line noise. It Figures 1 and 2 are photographs of digitized waveforms is ideal for protecting 400 Volt components because the solid state TVS technology showing the typical clamping action of a 16 ampere module. assures that the line-to-neutral voltage will not exceed 400 Volts. While the modules A 12 Ohm resistor is used to represent a 10 Amp equipment load. The load is then subjected to the ANSI/IEEE C62.41 are designed for transient voltage protection, the advanced circuitry will also attenuate Category CI test conditions (6,000V/3,000A). These photo- the amplitude and slow the rate of rise of high frequency noise acting as an EMI filter. graphs contrast the effect on equipment with and without the protector. The 587B Series includes differential mode and common mode protection, which is effective in reducing interference from line to equipment and are effective in reducing equipment generated noise to meet FCC, VDE and CSA interference requirements. 05016.R4 12/03 1 www.protekdevices.com 05016 Kilovolts Kilovolts 587B051 thru 587B301 DEVICE CHARACTERISTICS SPECIFICATIONS @ 25°C MAXIMUM RATINGS RESPONSE TO TRANSIENT VOLTAGES Operating Line Voltage: 130 VAC Max CLAMPING TEST CONDITION Maximum Line Current: 587B051: 5A PROTECTION MAXIMUM OPEN CIRCUIT SHORT CIRCUIT 587B151: 15A MODE CLAMPING VOLTAGE CURRENT 587B201: 20A VOLTAGE @ 1.2/50 µs @ 8/20 µs (Line-to-Neutral Only) 587B301: 30A DIFFERENTIAL 295V 1000V 500A Transient Voltage: 6000V peak (Line-to-Neutral) 350V 6000V 3000A Transient Current: 3000A peak COMMON 500V 1000V 500A Current Leakage: @ 130 VAC (Neutral-to-Ground) 650V 6000V 3000A Line-to-Neutral: 1.0mA Neutral-to-Ground: 0.5mA Storage & Operating FILTER CHARACTERISTICS (Noise Attenuation dB) Temperature: -40°C to 85°C 0.15 0.5 1.0 5.0 10 30 (Measured at center of Frequency (MHz) 10 25 35 55 50 40 Common Mode Attenuation mounting surface) 30 55 55 55 50 45 Differential Mode Attenuation ARRESTER DEFINITIONS Clamping Voltage: The clamping voltage of an arrester is the voltage that appears across its terminals during conduction of a transient current. Standard Wave Form: The waveform of a surge current or voltage is designated by a combination of two numbers. The first number is for the time of the wave front expressed in microseconds from zero to the peak of the wave. The second number is for the time of the wavetail also expressed in microseconds from zero to the instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 µs waveform. Transient Current: The transient current of an arrestor is the peak surge current which flows through the arrester when voltage clamping occurs. OPERA TION For maximum effectiveness, the protector should be installed directly after the AC line on/off switch and fuse. This will protect the electronics from the AC line switch arcing and the severe transients caused by a fuse clearing. Some heat is produced when operating at full current load, and heat sinking may be required to maintain case temperature below 85°C. The case temperature is measured at the center of the mounting surface. The unit should not be mounted to a low combusting temperature material such as wood. High energy transients will cause a large circulating current in the AC input line (2,500A is possible). To prevent electromagnetic coupling, the AC line on the input side of the protector must be dressed away from other wiring, magnetic shielding may be required. In addition, the electrical service must be connected to a low impedance earth ground. 05016.R4 12/03 2 www.protekdevices.com 587B051 thru 587B301 PACKAGE OUTLINE & DIMENSIONS D F E C LINE IN LINE OUT B INCLUDES HARDWARE Model 587B051 120V 50/60 Hz 5 AMP 2 NUTS, 2 WASHERS NEUTRAL GROUND PER TERMINAL 0.169” Nom. Dia. 2 Places A PROTEK CASE (INCHES) CASE (CENTIMETERS) APPROX. TERMINAL PART WEIGHT THREADS NUMBER IN GRAMS A B C D E F A B C D E F 587B051 2 2 2.5 2.85 1.5 0.6 5.08 5.08 6.35 7.62 3.81 1.52 250 #8-32 587B151 3 2 3.5 3.85 1.5 0.6 7.62 5.08 8.89 10.16 3.81 1.52 500 #8-32 587B201 3 3 3.5 3.85 1.5 0.6 7.62 7.62 8.89 10.16 3.81 1.52 750 M5 587B302 3 3 3.5 3.85 1.5 0.6 7.62 7.62 8.89 10.16 3.81 1.52 850 M5 ProTek Devices COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein 2929 South Fair Lane, Tempe, AZ 85282 without notice (except JEDEC). Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, Web Site: www.protekdevices.com ProTek assumes no responsibility with respect to the selection or specifications of such products. 05016.R4 12/03 3 www.protekdevices.com 37464-00001