® FIBERLIGN Hardware for ADSS: Section 6 ® Section 6 – FIBERLIGN Hardware for ADSS Page Table of Contents Fiber Optic Product Layout for ADSS ....................................................6-2 FIBERLIGN Lite Tension Dead-end for ADSS .......................................6-3 FIBERLIGN Dielectric Dead-end for ADSS ............................................6-5 FIBERLIGN Lite Support for ADSS ........................................................6-9 FIBERLIGN Dielectric Support for ADSS ...........................................6-12 FIBERLIGN Aluminum Support for ADSS ...........................................6-14 FIBERLIGN Aluminum Suspension for ADSS ....................................6-16 FIBERLIGN Dielectric Suspension for ADSS ......................................6-18 ADSS Product Layout ADSS FIBERLIGN Air FIBERLIGN CORONA ™ Dielectric Flow Spoiler Coil Damper FIBERLIGN FIBERLIGN Cable Abrasion FIBERLIGN Dielectric FIBERLIGN Protector Dielectric Suspension or Dead-Ends Dielectric FIBERLIGN IN-SPAN Aluminum Support, FIBERLIGN or Lite Storage System Aluminum Downlead Suspension Tension Cushion & Support, Dead-end Mounting or Lite ® COYOTE Accessories Support Closure or Splice Case FIBERLIGN See specific catalog ® Vertical COYOTE section for details Cable Defender Storage Note: For hardware accessories see sections 7 and 9. 6-2 ® FIBERLIGN Lite Tension Dead-end for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Lite Tension Dead-end for ADSS ® FIBERLIGN Lite Tension Dead-end for all Di elec tric Self-Supporting (ADSS) Fiber Optic Cable Installed 8. 1. 3. 2. 7. 4. 5. 6. NOMENCLATURE APPLICATION 1. Loop length: Length from the color mark to the end of The FIBERLIGN Lite Tension Dead-end is a di elec tric the loop. dead-end designed to terminate short span, low tension ADSS fi ber optic cables in low voltage envi ron ments. Un- 2. Loop diameter: The loop has a formed di am e ter de- ® like the Limited, Medium, and High Tension FIBERLIGN signed to interface with standard fi ttings Dielectric Dead-end designs found later in this section, the Lite Tension Dead-end is reduced to a single layer compo- 3. Color mark: The dead-end color mark or cross over mark nent that offers an economical solution for very light loads. locates the beginning of dead-end con tact with the cable The product effectively transfers the low axial load on the during installation. It is used for identifi cation as well. cable at the end of the dead-end legs to low uniform radial 4. Dead-end legs: The legs wrap onto the cable beginning compression near the dead-end loop. at the crossover mark. Superior Fatigue Strength: The small di am e ter wires that 5. Flared rod ends: Special rod end treatment to prevent comprise each dead-end are a mixture of aluminum and jacket damage. aluminum clad steel to assure long term performance. 6. Latex coating: Pliable coating applied over the dead- end legs. 7. Product ID Tag: Red Tag includes product de scrip tion and application information. 8. Pitch length: The distance along the leg that represents one complete wrap of the formed helix around the cir- cumference of the cable (360 de grees). 6-3 ® FIBERLIGN Lite Tension Dead-end for ADSS Dead-end performance depends upon a number of factors In general, Lite Tension Dead-ends are in tend ed for use including cable brand and design, tension load require- with these conditions and lim i ta tions: ments, tem per a ture and envi ron men tal operating con di tions Light Tensions, approximately: among others. -600# (2.7 kN) maximum initial (stringing/nom i nal axial/long-term) tension The FIBERLIGN Lite Tension Dead-end has a pli able latex -800# (3.5 kN) maximum loaded (working/loaded coating and fl ared rod end treatment that avoids possible axial/short- term) tension damage to the cable jacket during and after in stal la tion. Short Spans: -300' (91 m) maximum spans ATTACHING TO THE STRUCTURE: The loop di am e ter of -not recommended for critical crossing spans the Lite Tension Dead-end will fi t over a minimum diameter (highways, rivers, etc.) see Medium or High Ten sion of 1.5" (38mm) and a max i mum diameter of 2¼" (57 mm). Dead-ends The Lite Ten sion Dead-end is designed to accept common Very low strength cables guy wire dead-end pole fi ttings like thimble eyes and guy “Standard” jackets hooks. Most cable brands No excessive operating conditions, cable motion or high temperatures Lite Tension Dead-end features: Standard design parameters Broad cable OD ranges, listed on ID tags Economical single component design Optimized compact length Fast easy installation Thimble Guy Thimble Clevis Hook Eye Accepts standard pole line fi ttings Latex coated with fl ared rod ends Uniform pressure design Superior fatigue strength wire design Appropriate Fit tings The extended loop of the dead-end reduces the need for an extension link; however, PLP can provide other FIBER- ® LIGN fi ttings including exten sion links (with thimble clevis) if desired. PLP offers the TC-5F Thimble Clevis, Thimble Eye, and LCE-55-14 Ex ten sion Link. Cable Diameter Range Overall Length Catalog* Number Min (in) Max (in) Min (mm) Max (mm) Color Code inches meter 2875001 .375 .414 9.5 10.5 Red 28 .71 2875002 .415 .459 10.6 11.6 Orange 31 .79 2875003 .460 .505 11.7 12.8 Green 33 .84 2875004 .506 .557 12.9 14.1 Pink 37 .94 2875005 .558 .615 14.2 15.6 Yellow 42 1.07 2875006 .616 .680 15.7 17.3 Blue 45 1.14 2875007 .681 .750 17.4 19.1 Brown 49 1.24 5 *Add suffi x code TE to include Thimble Eye (Cat. No. TE-5) Number - Mount with ⁄ " or 16 m bolt and nut 8 6-4 ® FIBERLIGN Dielectric Dead-end for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Dielectric Dead-end for ADSS FIBERLIGN Di elec tric Dead-end installed NOMENCLATURE 14" Extension Link TC-5F or TC-5A Thimble Clevis 5 ⁄8" Eyenut Crossover marks Dead-end Component ID tag Structural Reinforcing Rod Com po nent ID tag GENERAL INFORMATION The FIBERLIGN Dielectric Dead-end product line has been Limited Tension Dead-ends: de signed to securely but gently terminate All Di elec tric Intended for rel a tive ly low tension application usu al ly as so - Self-Supporting (ADSS) aerial fi ber optic cable. A two com- ci at ed with short span construction. They are not cable or ponent design consisting of ap pro pri ate size and length of line design specifi c but are designed to fi t broad di am e ter Structural Reinforcing Rods and dead-end com po nent is rang es. Holding per for mance will vary by specifi c cable brand required to trans fer axial tensile loads and distribute radial and operating con di tions. Therefore, no specifi c hold ing com pres sive forces through the plastic jacket and onto the strength rat ing is possible. in ternal strength members without damaging the fr agile plastic jacket or internal optical fi bers. In general, Limited Tension Dead-ends are in tend ed for use with these conditions and lim i ta tions: APPLICATION & PRODUCT SELECTION Low tensions, approximately: -1,000# (4.4kN) maximum initial (string ing/nominal Specifi c dead-end design and performance de pends upon ax i al/long-term) tension -2,500# (11.1 kN) maximum a number of factors such as cable brand and design, loaded (work ing/loaded axial/short-term) tension strength member construction, jacket type, tension load Short spans: requirements, temperature and envi ron men tal operating -300' - 600' (91-183 m) typical max i mum spans conditions, and so on. Due to these factors, three types of depending upon ca ble OD and ten sions dead-ends are of fered: -not recommended for critical cross ing spans (highways, rivers, etc.); see Medium or High Tension Dead-ends Limited Tension Dielectric Dead-ends Low strength cables Medium Tension Dielectric Dead-ends “Standard” jackets High Tension Dielectric Dead-ends Most cable brands No excessive operating conditions, cable mo tion or 6-5 high temperatures ® FIBERLIGN Dielectric Dead-end for ADSS Limited Tension Dead-ends: (continued) Medium Tension Dead-ends: Limited Ten sion Dead-end features: Designed for medium tension applications. Hold ing Standard design parameters performance will vary by specific cable brand and operating conditions; therefore no, specifi c hold ing rating Broad cable OD ranges, listed on ID tags is pos si ble. Short Structural Reinforcing Rods Short dead-end component In general, Medium Tension Dead-ends are in tend ed for use with these conditions: Structural Reinforcing Rods and Dead-end Moderate tensions, approximately components pack aged in same car ton. -2,000# (8.9 kN) maximum initial (ever y day/string Fast, easy installation ing) tension -4,000# (17.8 kN) maximum loaded Utilizes economical TC-5F Thimble Clevis (short-term/work ing) tension maximum span length is de pen dent on ca ble O.D. and tensions Limited Tension Dead-ends For “standard” and most “track-resistant” jacket types of ADSS cables. (Con tact PLP to veri fy Cable O.D. Cable O.D. Overall Catalog Range Range Length Color ac cept able track-re sis tant ca ble.) Number* (inch) (mm) in. (m) Code For severe operating temperatures and con di tions 2872001 .400-.424 10.1-10.7 48 (1.2) Black Structural Reinforcing Rod length ranges from 85" to 105" (2.2 m — 2.7 m) 2872002 .425-.451 10.7-11.4 48 (1.2) Yellow 2872003 .452-.481 11.4-12.2 48 (1.2) Green Medium Tension Dead-end features: 2872004 .482-.510 12.2-12.9 48 (1.2) Orange Standard design parameters 2872005 .511-.542 12.9-13.7 48 (1.2) Blue Broad cable OD ranges, listed on ID tags 2872006 .543-.577 13.7-14.6 48 (1.2) White Moderate length 2872007 .578-.613 14.6-15.5 48 (1.2) Red Structural Reinforcing Rods and Dead-end components packaged in same car ton 2872008 .614-.651 15.5-16.5 48 (1.2) Black Utilize TC-5F (or TC-6F) Thimble Clevis 2872009 .652-.692 16.5-17.5 48 (1.2) Yellow Accessories can be ordered with Dead-end 2872010 .693-.737 17.5-18.7 48 (1.2) Green com po nents using suffi x codes 2872011 .738-.784 18.7-19.9 48 (1.2) Orange 2872012 .785-.834 19.9-21.1 48 (1.2) Blue Medium Tension Dead-ends 2872013 .835-.889 21.2-22.5 48 (1.2) White Cable O.D. Cable O.D. Overall 2872014 .890-.945 22.6-24.0 48 (1.2) Red Catalog Range Range Length Color Number (inch) (mm) in. (m) Code 2872015 .946-1.007 24.0-25.5 48 (1.2) Black 2872100 .482-.510 12.2-12.9 85 (2.2) Orange 2872016 1.008-1.073 25.6-27.2 60 (1.5) Yellow 2872101 .511-.542 12.9-13.7 85 (2.2) Blue 2872017 1.074-1.140 27.2-28.9 60 (1.5) Green 2872102 .543-.577 13.7-14.6 85 (2.2) White 2872018 1.141-1.212 28.9-30.7 60 (1.5) Orange 2872103 .578-.613 14.6-15.5 85 (2.2) Red 2872019 1.213-1.288 30.8-32.5 60 (1.5) Blue 2872104 .614-.651 15.5-16.5 85 (2.2) Black *T o include ac ces so ries in same carton, add suf fi x code(s) to Dead- 2872105 .652-.692 16.5-17.5 85 (2.2) Yellow end cat a log num ber. Ex am ple: Cat. No. 2872001C1E1 in cludes Dead-end #2872001, TC-5F Thim ble Clevis and Ex ten sion Link 2872106 .693-.737 17.6-18.7 85 (2.2) Green #71002366 in the same carton. See Dielectric Dead-end ac ces - 2872107 .738-.784 18.7-19.9 85 (2.2) Orange so ries in this section. 2872108 .785-.834 19.9-21.1 90 (2.3) Blue CAUTION: Some ADSS ca bles are not suit able for use with 2872109 .835-.889 21.2-22.5 90 (2.3) White Lim it ed Ten sion Dead-ends. Limited Tension Dead-ends 2872110 .890-.945 22.6-24.0 95 (2.4) Red are not recommended for track-resistant jacket applications. Consult PLP for spe cifi cs. 2872111 .946-1.007 24.0-25.5 95 (2.4) Black 2872112 1.008-1.073 25.6-27.2 97 (2.5) Purple 2872113 1.074-1.140 27.2-28.9 100 (2.5) Pink 2872114 1.141-1.212 28.9-30.7 103 (2.6) Brown 2872115 1.213-1.288 30.8-32.5 105 (2.7) Orange 6-6 ® FIBERLIGN Dielectric Dead-end for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Dielectric Dead-end for ADSS High Tension Dead-end features: High Tension Dead-ends: Custom design parameters Custom designed and manufactured for more strin gent Designed for specifi c cable diameter and OD holding re quire ments and operating conditions than Lim it ed and Medium Tension Dead-ends. Hold ing per for mance ranges, listed on ID tags will vary depending upon the spe cifi c cable brand and Custom length Structural Reinforcing Rods operating conditions, there fore no gen eral holding strength and Dead-ends to match tension ap pli ca tions ® rating is pos si ble. Con sult PLP for the proper dead-end Structural Reinforcing Rods and Dead-end application. components packaged in same carton Utilizes either ATC-20M and TC-6F Thimble In general, High Tension Dead-ends are intended for use Clevis with these conditions: Accessories can be ordered with Dead-end High tensions, approximately components using suffi x codes - over 2,000# (8.9 kN) initial (everyday/string ing) tension - over 4,000# (17.8 kN) loaded tension Long spans - varies according to cable OD and tensions High strength circular cables “Standard” and “track resistant” jackets All cable brands Selection and design considers excessive op er at ing conditions, cable motion and high tem pera ture envi- ronments Figure 8 Fiber Optic Cable: Ordering Instructions: For All-Di elec tric messengers, the messenger with jacket For Limited Ten sion and Medium Tension Dead-ends, in tact is separated from the fi ber bundle and a two piece use the ap pro pri ate table in this sec tion if your in stal la tion Di elec tric Dead-end is applied over the jack et ed mes sen ger. meets the re stric tions for this prod uct. For all other dead- For metallic mes sen gers, a conv en tion al strand dead-end ends, con tact PLP with cable spec i fi ca tions, line de sign is applied di rect ly to the bare mes sen ger. Consult PLP for details and advise of unusu al op er at ing con di tions or high specifi cs for either style mes sen ger. tem pera ture envi ron ments so that prop er dead-end de signs can be se lect ed. Component Reuse: Once installed, the struc tural reinf orcing rods and formed To have accessories included with any Dead-end, add the dead-end com po nents may be removed and reinstalled appropriate suffi x to the dead-end cat a log number. Example: once for repositioning purpos es; do not reuse after this #2872001C1E1 in cludes Dead-end #2872001, Thimble initial installation. The hard ware may be reused as desired Clevis TC-5F and Extension Link kit. See next page for if in good condition. Do not mod i fy any com po nent. available ac ces so ries. 6-7 ® FIBERLIGN Dielectric Dead-end for ADSS All Dielectric Dead-ends require a prop er size and strength Thimble Clevis and may utilize an Ex ten sion Link. To include accessories with dead-end, add suffi x code(s) to Dead-end catalog number. Thimble Clevis: TC-5F Thimble Clevis ATC-20M Thimble Clevis Limited and Medium Tension Dead-ends require the (Code C1) (Code C2) Catalog No. TC-5F Thimble Clevis (Rated Strength 26,900# (119 kN)) suffi x Code “C1” or Cat No. TC- 5A Thimble Clevis (Rated Strength 12,000# (53 kN)). The galvanized ductile iron #TC-5F is standard with a 7 2¼" minimum seat and ⁄ " minimum groove di am e ter. The 8 aluminum #TC-5A is optional with the same dimensional characteristics. High Tension Dead-ends require at least the 20,000# (89 kN) ATC-20M Thimble Clevis (code C2) or equal with 3" min i mum seat and 1½" minimum groove di am e ters. For TC-6F Thimble Clevis (Code C4) higher loads, use the 42,400# (188 kN) TC-6F (code C4) galvanized iron Thimble Clevis or equal with 2½" minimum 1 seat diameter and 1 ⁄ " min i mum groove diameter. 16 Extension Link: An optional 15,000# (67 kN) 14" (356 mm) Ex ten sion Link A 5 with ⁄ " Eye Nut (Cat. #71002366, code E1) is sug gest ed 8 and some times rec om mend ed by cable sup pli ers to in crease the ca ble bending radius and re duce stress to the optical fi bers at Dead-end lo ca tions. This link kit can be used with B any type FIBERLIGN Dielectric Dead-end. (A) 14" Extension Link with Eye Nut, 15K (Cat. No. 71002366, code E1) For higher loads, use the 25,000# (111 kN), 14" (356 mm) Extension Link (Cat.# LCE-66-14 or P/N 00060132 or (B) 25K EXTENSION LINK code E2). (Cat. No. LCE-66-14, code E2) Loads up to 36,000 pounds can be handled with Cat. No. 000601325 (not shown). Banding Bracket: Dielectric Dead-ends can be banded to con crete or steel structures using the 12Klb Banding Bracket Kit (Cat. #710010745, code B1). The kit includes a 5 ⁄ "-11x2" long bolt, lockwasher, hex nut and band- 8 ing bracket. This connects to the Ex ten sion Link with 5 ⁄ " eye nut referenced above (Cat #71002366). The bracket 8 is rated for 12,000# (53 kN) and should be used with two high strength 1¼" steel bands (not supplied). 12Klb Banding Bracket Kit (Cat. No. 710010745, code B1) 6-8 ® FIBERLIGN Lite Support for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Lite Support for ADSS FIBERLIGN Lite Support for All Dielectric Self-Supporting FIBERLIGN Lite Support for All Dielectric Self-Supporting (ADSS) Fiber Optic Cable—Bolt Mounted (ADSS) Fiber Optic Cable—Band Mounted Double Arming Band Bolt NOMENCLATURE 1. Housing Halves: FLS Urethane housings have molded cav i ties to accept cushion inserts. The small cavity accepts a small insert (Item 2a). The large cavity is de signed for string ing in cable, ca pa ble of handling up to a 1¼" (32 mm) diameter mechanical 2a swivel with pulling in grip. The large cav i ty will accept a large insert (Item 2b) for larger cables or if a dual cable 3 ap pli ca tion is desired. 1 2. Insert: Softer material than the housing (item 1), one piece inserts are slot ted to accept the cable as well as cushion the cable under load. The cable di am e ter range is molded along the hinge opposite the open slot for identifi cation. 2b The small insert (Item 2a) will accept ca ble sizes up to .700" (17.8 mm) di am e ter. The large insert (Item 2b) will accept cable sizes up to 1.03" (26 mm) di am e ter. 3. Hardware Kit (op tion al) for Banded Mount: 5 5 A ⁄ "-11 UNC by 4" long car riage bolt, ⁄ " round washer, 8 8 5 Lock Wash er, and ⁄ "-11 UNC nut can be provided for 8 band ing applications. (Cat. No. 4800500) 6-9 ® FIBERLIGN Lite Support for ADSS APPLICATION Material: The FIBERLIGN Lite Support (FLS) system is de signed The housing halves are made from a high-strength, to gently but fi rmly support All Dielectric Self-Sup port ing (ADSS) cable. It is intended for tangent support in stal la tions dielectric urethane material. The cush ioned inserts are (see “LINE ANGLES”) on lines that feature low voltages, made from a softer, pliable di elec tric material that gently very short spans and low mechanical loads. For products grips and cushions the ADSS cable within the clamped housing. The hardware (optional) for banded applications with higher ca pa bil i ties see the subsequent pages under ® is zinc plated. FIBERLIGN Dielectric Sup port, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Di elec tric Sus pen sion. The two Mounting: latter products can be used in higher voltage envi ron ments The housing halves are molded with smooth fi nish holes 5 to accept a stan dard ⁄ " thru-bolt. where track resistant ADSS cables are re quired. 8 Dual Insert Application: Bolt Mount: The FLS with small and large inserts can support two cables. For wood pole or bolt mount ing to any structure, a thru bolt Existing FIBERLIGN Dielectric Support (FDS) installations can be fed through a hole in the structure leav ing 4" to 5" (102-127 mm) of the bolt exposed to accept the FLS and (up to 300' spans) can be replaced or “retrofi tted” using the allow for tem po rary housing separation during installation. FLS. This option increases capability from one to two cables within minimal pole space. At four (4) inches (102 mm), the nut and washers can be left on the end of the bolt while manipulating the hous ing FTTP: halves to remove the cable after stringing or accept the insert during fi nal installation. Fiber to the Premisis drop cables can have round, fl at and fi gure 8 construction. Specially designed Lite Support inserts are available to accept all of these confi gurations. Band Mount: The catalog table includes these new sizes and detailed For concrete pole or band mount ing to any struc ture, the information can be found in Section 8. housing halves have a molded groove that ac cepts ¾" wide high-strength banding material. PLP provides the hardware kit (item 3 of the no men cla ture) that is used to clamp the Stacking: LITE Support Housings are stackable to add more cables housing halves to geth er after the unit is banded to the struc- within the same pole space. This can offer a neat alternative ture. The housings have a special recessed hole that keeps to busy “J-Hook” clutter for FTTP drop cable distribution. the car riage bolt from turning during as sem bly. To include the mounting hardware with the product add the suffi x code H2 to the stan dard FLS catalog num ber. Banding material Maximum Span Lengths – 300 feet (91 m): The max i mum recommended span length for the FLS is is not provided – Consult PLP for further information. dependent upon the specifi c cable OD, initial cable tension, ice and wind load ing district (NESC), and other factors. It is Line Angles: For most applications, the max i mum line angle rec om - intended for application on short spans where vertical loading mend ed is 20°; consult PLP for excep tions. does not exceed 1000# (4.4 kN) under the extreme case. In general, the approximate recommended max i mum span Slip Loads: length for the FLS is 300 feet (91 m) under extreme loads The hourglass shape of the insert cre ates wedge-action holding on the cable when un bal anced loads exist. The (NESC Heavy). Consult PLP for spe cifi c span limitations. wedge works in either di rec tion. Holding capability is en- hanced with a special knurled fi nish on the inserts inner diameter surface. Specifi c per for mance will depend upon the specifi c cable OD and design. 6-10 ® FIBERLIGN Lite Support for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Lite Support for ADSS STRINGING OPERATIONS The dielectric ma te ri al of the body provides a high ly abrasive- resistant surface that allows the FLS hous ing assembly to be used as a stringing traveler at the structure. The smooth surfaces of the housing are designed with gentle contours and large radii that allow up to 10° line angles (20° in certain cases – consult PLP). This ability saves in stal la tion time and costs by elim i nat ing the use of conventional string ing trav el ers. For stringing operations the large molded cavity will accept up to 1¼" diameter for pulling in hard ware. If you are using cable greater than .699" (18 mm) di am e ter, you may have a large insert designed for the large molded cavity. If so, remove the large insert from its cavity and temporarily tighten the FLS housing halves against the pole. The small insert can remain in the small cavity of the FLS during stringing. ORDERING INSTRUCTIONS Cable Diameter Range Catalog Insert Min Max Min Max Refer to the cat a log table and select the proper FLS for Number Size (in) (in) (mm) (mm) the cable's outside di am e ter. To include the carriage bolt 4800107 .250 .280 6.3 7.0 hard ware kit for Cat. no. 4800500 band mount, add suffi x 4800108 .281 .304 7.1 7.7 code H2 (banding material not included). EX: #4800110H2 will include hardware. 4800109 .305 .375 7.8 9.5 4800110 .400 .429 10.2 10.8 4800111 .430 .459 10.9 11.6 S 4800112 .460 .489 11.7 12.4 M A 4800113 .490 .519 12.5 13.1 L 4800114 .520 .549 13.2 13.9 L 4800115 .550 .579 14.0 14.7 4800116 .580 .609 14.8 15.4 4800117 .610 .639 15.5 16.2 4800118 .640 .669 16.3 16.9 4800119 .670 .699 17.0 17.8 4800120 .700 .723 17.9 18.3 4800122 .724 .779 18.4 19.7 L 4800124 .780 .834 19.8 21.1 A R 4800126 .835 .889 21.2 22.5 G 4800128 .890 .944 22.6 23.9 E 4800130 .945 .999 24.0 25.4 4800132 1.000 1.054 25.5 26.8 DUAL INSERT APPLICATION: Catalog Numbers are avail- able for Small & Large Insert Combinations - Contact PLP 6-11 ® FIBERLIGN Dielectric Support for ADSS FIBERLIGN Dielectric Support installed APPLICATION The FIBERLIGN Dielectric Support (FDS) system is designed to gently, but fi rmly, support All-Di elec tric Self- Supporting (ADSS) cable. It is intended for tan gent support installations (see “LINE ANGLES”) on lines that feature relatively low voltages, short spans and modest mechanical loads. For higher voltages (where “track resistant” ADSS cables are required), longer spans and/or higher loads, use either the FIBERLIGN Aluminum Suspension with Rods or the FIBERLIGN Di elec tric Suspension — both prod ucts appear later in this section. Maximum Span Lengths: The maximum rec om mend ed span length for the FDS is de pen dent upon the specifi c cable OD, initial cable ten sion, ice and wind loading district (NESC), and other fac tors. It is intended for application on rel a tive ly short spans where For mounting to concrete or steel structures without thru- 5 ver ti cal cable loading does not exceed ap prox i mate ly 1,000# holes, use a ⁄ " threaded stud of ap pro pri ate length or 8 (worst case). In gen eral, the ap prox i mate recommended banding system with a mounting bracket. See accessories max i mum span lengths for the FDS are: in this section for details about the Limited Tension Band- ing Bracket. 600' for < 1.00" OD cable (NESC – heavy). 300' for ≥ 1.00" OD cable (NESC – heavy). Line Angles: For most applications, the max i mum line angle recom- When in doubt, consult PLP for specifi c span lim i ta tions. ® mended is 20˚; consult PLP for exceptions that allow 30˚ angles. When angles exceed 20˚ (or 30˚) a double dead- Material: end arrangement is usually preferred. A special double The body and top are made from a high-strength, engineered FDS unit can be designed for certain applications; consult dielectric material. The cushioned inserts are made from a PLP for details. soft, pliable dielectric material that gently grips the ADSS cable. Two captured zinc plated bolts with wash ers secure Slip Loads: the top to the body. The cushioned inserts are de signed to gently grip the cable while providing signifi cant slip strength without causing cable Mounting: jacket damage. Specifi c performance will depend upon the 5 The body threads onto standard ⁄ " 11-UNC hot dipped 8 specifi c cable O.D. and design. galvanized thru-bolt and may be mount ed ei ther hori zon tal ly or vertically. For hor i zon tal mount ing to a wood pole (or other structures with thru-holes) a double arming bolt (completely NOMENCLATURE threaded–no head) is sug gest ed instead of a fi xed length 5 machine bolt. This allows approximately 1 ⁄ " of bolt length 8 FDS to thread into the body re gard less of pole diameter. Captive hard ware Top Body Cushioned inserts PATENTED 6-12 ® FIBERLIGN Dielectric Support for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Dielectric Support for ADSS Stringing Operations: The dielectric ma te ri al of the body provides a highly abra- sive-resistant surface that allows the FDS body to be used as a stringing traveler at the structure on up to 10˚ line ® angles (20˚ in certain cases–consult PLP ). This abil i ty saves installation time and costs by eliminating the use of conventional stringing travelers. For stringing operations, thread the FDS onto the appro- priate bolt, remove the inserts and elevate the top as far away from the bottom as the bolts will allow, to provide as large an opening as possible. Then thread pulling-in cable through the opening. Component Reuse: All components of FDS may be reused as desired if in good condition. Do not modify any component. Cable OD Range Ordering Instructions: inches (mm) Catalog Number For concentric ADSS cable, refer to the catalog table and .275-.325 (7.0-8.3) 44002144 select the proper FDS for the cable’s outside diameter. For non-con cen tric profi les, such as Figure 8 or other cable sizes .326-.375 (8.4-9.5) 44000691 and profi les, consult PLP for custom designs. To include .376-.425 (9.6-10.8) 44009998 accessories with the FIBERLIGN Di elec tric Support, add code number to catalog number (ex am ple: 44002144B1). .426-.475 (10.9-12.1) 44009949 .476-.525 (12.2-13.3) 44009952 .526-.575 (13.4-14.6) 44009823 ACCESSORIES .576-.625 (14.7-15.9) 44009798 The FIBERLIGN Dielectric Support may be banded to .626-.675 (16.0-17.1) 44009776 con crete or steel struc tures using the appropriate Limited .676-.750 (17.2-19.1) 44009799 Ten sion Banding Bracket Kit (Cat. #710010577, code B1). 5 The kit includes a ⁄ "-11 x 2½" long bolt, lockwasher, hex 8 .751-.825 (19.2-21.0) 44009878 nut and band ing bracket. The bracket is rated for 1,200# .826-.900 (21.1-22.9) 44009963 vertical load and should be used with a high strength 1¼" .901-.950 (23.0-24.1) 44002213 steel band (band pur chased sep a rate ly). .951-1.000 (24.2-25.4) 44003915 1.001-1.050 (25.5-26.6) 440010296 6-13 ® FIBERLIGN Aluminum Support for ADSS Through-Bolt Mounted Band Mounted Multi-Cable Stacking Captured Bolt and Bevel Washer: Gal va nized steel bolt, lock washer and washer captured with an elas tomer 4. FAS grommet. 2. Cushion Inserts: A soft pliable dielectric ma te ri al that gently Grommet grips the ADSS cable. FAS is the acronym for FIBERLIGN 3. Aluminum Support. APPLICATION The FIBERLIGN Aluminum Support (FAS) is de signed to gently, but fi rmly support All-Di elec tric Self-Supporting (ADSS) cable. The FAS features the following: Integrated bolt or band mount design, Hinged keeper and base, Single- bolt clamping, and Stackability for multi-cable installations. For high er voltages (where track resistant ADSS cables are Band ing Slot required), longer spans and/or higher loads, use ei ther the Through Hole for FIBERLIGN Aluminum Suspension w/rods or the FIBER- Through Bolt 1. LIGN Dielectric Sus pen sion – both prod ucts appear later in this section. PATENT PENDING Maximum Span Lengths: The FAS was designed for short span applications where NOMENCLATURE vertical loading does not exceed 1000# (4.4 kN). The maxi- mum vertical load typically fac tors-in span length, cable OD, 1. Base initial cable tension, ice and wind loading district (NESC), 2. Keeper multi-cable stack ing, etc. As a general idea, the following 3. Cushion Inserts rec om men da tions are approximate maximum span lengths 4. Captured Bolt, Lock Washer & Flat Washer for the FDS under NESC Heavy con di tions: (Captured with grommet) 600' (183 m) for < 1.00" (25 mm) OD cable (NESC Heavy) Base and Keeper: The aluminum alloy base and keeper 300' (91 m) for > 1.00" (25 mm) OD cable have an interlocking hinge al low ing easy access for pull- (NESC Heavy) ing-in rope and ADSS cable. Closing the keeper captures the cable during stringing and subsequently secures the Mounting: cable and cushion inserts for permanent installation. The The FAS can be bolted or banded to a structure. For mount- base is designed to ac cept a 1¼" wide x .040" thick (32 mm ing to wood poles (or other structures with through holes) 5 x 1 mm) band or a ⁄ " through bolt (M16) for mounting to 8 5 a ⁄ "-11 (M16) through-bolt or dou ble-arming bolt may be 8 the structure. In multi-cable in stal la tions, modular base used to capture the FAS against the structure. The width of surfaces at the mounting bolt and band entry areas provide the FAS ac counts for about 3.2" (81 mm) of bolt length. sta ble en gage ment and stacking. 6-14 ® FIBERLIGN Aluminum Support for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Aluminum Support for ADSS For mounting to concrete or steel structures with out through Torque Level: 5 holes, the FAS may be banded via the band slot cast in The keeper is fastened to the base with the ⁄ "- 16 captured 8 the base of the FAS. The band slot is designed to accept bolt and should be tightened until the lock washer is fl at for a 1¼" wide x 0.040" thick (32 mm x 1 mm) high strength proper torque level. This will re quire 10 foot pounds (120 band. Banding ma te ri als with 45,000 psi (310 MPa) yield inch-pounds or 13.5 New ton-meters) of force. DO NOT strength and 95,000 psi (655 MPa) ul ti mate strength are OVER-TORQUE. recommended to achieve rated vertical load. Stacking – Multi Cable Installation: Line Angles: Multi-cable installations with the FAS save pole space as the For most applications, the maximum line angle recom- fi rst unit mounts against the pole and added units extend ® 5 mended is 20˚ – consult PLP for excep tions that allow 30˚ horizontally – captured with a common ⁄ " (M16) bolt. The 8 angles. When angles exceed 20˚ (or 30˚) the FIBERLIGN length of the bolt must ac com mo date the stacked FAS units Aluminum Sus pen sion (found later in this section) as a – each width approximately 3.2" (81 mm). For installations single or double at tach ment may be considered as an of more than two cables, a brace should be used to help alternative. support the cantilever load on the through-bolt or band. Longitudinal Holding Capability: The FAS units stack in such a way that keep ad ja cent cables The cushioned inserts are designed to gently grip the in staggered formation, thus reducing the possibility of cable cable – providing modest longitudinal holding strength collision due to wind induced cable sway. without causing cable damage. Specifi c per for mance will depend upon the cable brand, in ternal con struc tion, and outer diameter. ORDERING INSTRUCTIONS Stringing Operations: Refer to the catalog table and select the ap pro pri ate FAS The cable cavity of the FAS is contoured and smooth to for the ADSS cableís outside diameter. allow the product to be used as a stringing travel er during stringing and sagging operations. The line angles during ® FIBERLIGN Aluminum Support stringing may go up to 10˚ (20˚ in cer tain cases – consult ADSS Cable Range PLP). Catalog Min Max Min Max For stringing, the inserts are removed and the keep er should Number (in) (in) (mm) (mm) be fully closed with the bolt fully engaged. 4450095 0.226 0.275 5.7 6.9 4450096 0.276 0.325 7.0 8.2 4450097 0.326 0.375 8.3 9.4 4450098 0.376 0.425 9.5 10.7 4450099 0.426 0.475 10.8 12.0 4450100 .476 .525 12.1 13.3 4450101 .526 .575 13.4 14.6 4450102 .576 .625 14.7 15.9 4450103 .626 .675 16.0 17.1 4450104 .676 .750 17.2 19.1 4450105 .751 .825 19.2 21.0 4450106 .826 .900 21.1 22.9 4450107 .901 .975 23.0 24.8 4450108 .976 1.05 24.9 26.7 Stringing 4450109 1.051 1.25 26.8 28.6 4450110 1.126 1.20 28.7 30.5 4450111 1.201 1.275 30.6 32.4 4450112 1.276 1.35 32.5 34.3 4450113 1.351 1.425 34.4 36.2 6-15 ® FIBERLIGN Aluminum Suspension for ADSS Low to High Voltage Environment acceptance. The addition FASN of SRR allows the versatile FASN to go from a dis tri bution 4. environment to a transmission environment. Fittings and brackets are available for wood pole and concrete or metal 3. structure applications. Span Length Capability 2. 1. 1. For short spans without SRR: <600' (183 m) maximum recommended span lengths. 2. For Intermediate spans with SRR: <1200' (366 m) maximum recommended span lengths. For additional cable jacket protection, longer spans and higher longitudinal holdling requirements, the dual rod layer FIBERLIGN Dielectric Suspension (found later in this section) is recommended. NOMENCLATURE 1. Keeper 2. Cushion Inserts (With or Without Grit) 3. Captured Bolt and Washer (Captured with Grommet) 4. Lock Nut 5. Anchor Shackle with Eye-nut (Optional not shown) 6. Structural Reinforcing Rods (optional, not shown) Keeper: The aluminum alloy keepers have an in ter lock ing hinge for simple access and cable in stal la tion. Clos ing the keeper captures and se cures the cushion inserts and ADSS cable. The keep ers join together to form a clevis for at tach ment to the struc ture via Cat. No. AS-5L anchor shackle fi tting Anchor Shackle w/Eye Nut Option or equivalent. Cushion Inserts: A soft pliable dielectric material that gently grips the ADSS cable – supplied either with or without grit on the inner diameter bore. Gritted inserts are ap plied over optional Structural Reinforcing Rods for medium span applications. The gritted inserts have a conductive aluminum strip located near the center for higher voltage environments. Captured Bolt, Washer, and Lock Nut: FASN with Rods Galvanized steel bolt and washer captured with an elasto- mer o-ring. The galvanized steel Lock Nut has a stiff wire Vertical Load Limit locking mechanism designed to engage with the thread of The FASN has an ultimate verti cal load capability of 7000 the mating bolt. (31 kN) pounds. Structural Reinforcing Rods (SRR) Longitudinal Cable Holding Capabilities are preformed galvanized steel rods – subsetted and grit- Without SRR, modest longitudinal holding ca pa bil i ties ted. They are intended to provide additional protection to are provided via compresson of the non-gritted inserts the cable jacket and increase lon gi tu di nal holding abilities on the cable. Specifi c values are de pen dent upon cable of the unit. brand, internal construction and diameter. Consult PLP FASN is the acronym for FIBERLIGN ALU MI NUM SUS- for specifi cs. PENSION. With SRR, substantial longitudinal holding ca pa bil i ties are provided via insert compression and are enhanced by the grit APPLICATION on both the inserts and SRR. Contact PLP for specifi cs. Rod End Treatment The FIBERLIGN Aluminum Sus pen sion (FASN) is designed to gently, but fi rmly support All-Dielectric Self-Supporting In order to avoid scratching, gouging or nicking of the plastic jacket during installation, unbalanced loading, or cable mo- (ADSS) cable. The FASN features the following: Interlocking tion, the ends of eh SRR's are factory formed to fl are away Hinge, Single-bolt clamp ing, Short to Medium Span Option, from the cable surface. 6-16 ® FIBERLIGN Aluminum Suspension for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Aluminum Suspension for ADSS Grounding and Corona Pro tec tion: FASN Kit Without Structural Reinforcing Rods If positive grounding of the cable and metalic components ADSS Cable Range of the FASN is desired, a grounding wire can be attached 3 Catalog Min Max Min Max to the ⁄ " captured bolt. PLP can supply a 4' (1.2m) long 8 Number* (in) (in) (mm) (mm) #4 copper or 4/0 alu mi num grounding wire assembly (Cat. 4450195 0.226 0.275 5.7 6.9 No. 710010016 or 710010294 respectively). 4450196 0.276 0.325 7.0 8.2 4450197 0.326 0.375 8.3 9.4 For the FASN, the SRRs have been designed to accept the ™ 4450198 0.376 0.425 9.5 10.7 ADSS-CORONA Coil. The ADSS CO RO NA Coil reduces electrical stress at the ends of the metal rods. 4450199 0.426 0.475 10.8 12.0 Further catalog information about this product can be found 4450200 0.476" 0.525" 12.1 13.3 later in this section. 4450201 0.526" 0.575" 13.4 14.6 4450202 0.576" 0.625" 14.7 15.9 Mounting 4450203 0.626" 0.675" 16.0 17.1 Bolted (Wood Poles): Adding suffi x code “S” provides 5 4450204 0.676" 0.750" 17.2 19.1 an anchor shackle with ⁄ "-11 eye nut accessory (Cat. 8 4450205 0.751" 0.825" 19.2 21.0 No. 710010357) for at tach ment to dou ble arm bolts. The 4450206 0.826" 0.900" 21.1 22.9 an chor shack le (Cat. No. AS-5L) may be purchased 4450207 0.901" 0.975" 23.0 24.8 sep a rate ly to attach to eye bolts. 4450208 0.976" 1.050" 24.9 26.7 Banded (Steel, Concrete Poles): Banding Bracket (Cat. 4450209 1.051" 1.125" 26.8 28.6 No. 710010577) is offered for low ten sion/short span 4450210 1.126" 1.200" 28.7 30.5 5 support application only. The kit includes a ⁄ "-11x 2½" 8 4450211 1.201" 1.275" 30.6 32.4 long bolt, lockwasher, hex nut and banding bracket. The 4450212 1.276" 1.350" 32.5 34.3 bracket is rated for 1,200# (5.3 kN) vertical load and 4450213 1.351" 1.425" 34.4 36.2 should be used with a high strength 1¼" (32 mm) steel *Add Suffi x “S” to Catalog No. to include one #AS-5L Anchor Shackle band (band pur chased sep a rate ly). and 5/8" Eye-Nut Line Angles The FASN maximum rec om mend ed line angle for a single Refer to the catalog tables (with or without rods) and se- sus pen sion unit is 30˚ de pend ing on cable brand. Two units lect the ap pro pri ate FASN for the ADSS cables outside can be combined to turn larger angles up to 60˚, although di am e ter. double dead-ending is another option for large angles. Add suffi x code “S” to include anchor shackle with 5/8" Contact PLP for de tails. eye-nut (Cat. No. 710010357) option. Torque Level Order Cat. No. 710010577 to receive the Limited Tension 3 The ⁄ " captured bolt should be tightened UNTIL THE LOCK 8 Banding Bracket – see “Mount ing” para graph earlier in this WASHER IS FLAT and the clevis halves are joined fl ush. section for details. This will require about 10 foot-pounds (120 inch-pounds or 13.5 New ton-meters) of force. DO NOT OVER-TORQUE. Order Cat. No. 710010016 to receive a 4' (1.3 m) long #4 (7W) copper with terminal on one end. Order Catalog No. 710010294 to receive a 4' (1.2 m) long 4/0 (7W) alu mi num ORDERING INSTRUCTIONS conductor with terminal on one end. FASN Kit with Structural Reinforcing Rods ADSS Cable Range Rod Catalog Length Rod Dia. Color Number* Min (mm) Max (mm) (mm) (mm) Code 4470200 0.476" (12.1) 0.500" (12.7) 33" (838) .100" (2.5) Red 4470201 0.501" (12.8) 0.550" (14.0) 34" (864) .100" (2.5) Blue 4470202 0.551" (14.1) 0.625" (15.9) 34" (864) .100" (2.5) Black 4470203 0.626" (16.0) 0.700" (17.8) 35" (889) .100" (2.5) Orange 4470204 0.701" (17.9) 0.737" (18.7) 36" (914) .119" (3) Green 4470205 0.738" (18.9) 0.812" (20.6) 36" (914) .119" (3) Pink 4470206 0.813" (20.7) 0.887" (22.5) 37" (940) .119" (3) Purple 4470207 0.888" (22.6) 0.962" (24.4) 37" (940) .119" (3) White 4470208 0.963" (24.5) 1.037" (26.3) 37" (940) .119" (3) Yellow 4470209 1.038" (26.4) 1.112" (28.2) 38" (965) .119”" (3) Brown 4470210 1.113" (28.3) 1.187" (30.1) 39" (991) .119" (3) Red *Add Suffi x “S” to Catalog No. to include one #AS-5L Anchor Shackle 6-17 ® FIBERLIGN Dielectric Suspension for ADSS Fiberlign Dielectric Suspension for All-Dielectric Self-Sup port ing (ADSS) Cable APPLICATION ® Product Selection The FIBERLIGN Dielectric Sus pen sion is specifi cally designed for installation on ADSS cables and is different As a general guideline, the FIBERLIGN Dielectric Suspen- ® than FIBERLIGN Sus pen sion for OPGW. Due to the rela- sion for ADSS is intended for long spans where suspension tively fragile nature of the plastic jackets and nonmetallic is desired regardless of span, where very high unbalanced longitudinal holding strengths are desired, or where very strength members of ADSS, special care and features are high vertical loads are expected. incorporated into the design of the FIBERLIGN Di elec tric Sus pen sion. PLP offers two other products for lighter load/shorter span The unit does use a combination of Structural Re in forc ing applications in suspension and support modes. Refer to the FIBERLIGN Dielectric Support (FDS), FIBERLIGN Alumi- Rods, Outer Rods, boltless housing and re sil ient cable num Support (FAS) and FIBERLIGN Aluminum Suspension inserts to reduce com pres sion clamp ing and bending stresses on the cable and glass fi bers. Negative effects (FASN) products that appear earlier in this section. of wind induced cable motions such as aeolian vibration, galloping and wind sway are also minimized. ULTIMATE VERTICAL STRENGTH & HOUSING & FITTING DIMENSIONS: Re fer to di men sion al tables in the FIBER- LIGN Sus pen sion for OPGW sec tion of this catalog. The double layer of rods also offers critical pro tec tion against tearing of the plastic jacket during un bal anced longitudinal loading of the cable while provid ing substantial Line Angles holding strength. This holding strength can vary according The maximum recommended line angle for a single suspen- sion unit is 40˚. A custom designed FIBERLIGN Dielectric to cable brand, jacket type, operating temperatures and Suspension Double for angles up to 80˚ is available. Double other factors. dead-end ing for angles over 40˚ is another option. For further details about the product and its com po nents, refer to FIBERLIGN Suspension for OPGW earlier in this Fittings Fittings such as a Y-Clevis, Clevis Eye, Chain Link or Anchor section. Shackle may be required to attach the Suspension unit to Rod End Treatment the structure or other hardware. These fi ttings must match In order to avoid scratch ing, gouging or nicking of the plas- the di men sions of the suspension housing; refer to the tic jacket during installation, unbalanced loading, or cable di men sion al tables and fi ttings pages in the FIBERLIGN Sus pen sion for OPGW section of this catalog. motion, the Structural Reinforcing Rods are slightly fl ared away from the cable surface. Unfl ared rod ends can cause damage to the jacket which should be avoid ed. Component Reuse Once installed, do not re use the rod components. The hardware com po nents may be reused as long as they are in good condition. Do not modify any com po nents. 6-18 ® FIBERLIGN Dielectric Suspension for ADSS ® FIBERLIGN Hardware for ADSS: Section 6 ® FIBERLIGN Dielectric Suspension for ADSS ORDERING INSTRUCTIONS Select the ap pro pri ate FIBERLIGN Dielectric Sus pen - sion for ADSS by cable di am e ter from the table below. For FIBERLIGN Sus pen sion for OPGW, refer to page section 5-19 of this catalog. For trunnion or bracket-type ® mounting for ADSS or OPGW, consult PLP . Diameter Range Structural Reinforcement Rods Outer Rods Length Rod Diameter Length Rod Diameter Catalog Min.-Max. Min.-Max. Rods Color Rods Color Number (in) (mm) (in) (meters) (in) (mm) per set Code (in) (meters) (in) (mm) per set Code 430010267 .354 .381 8.9 9.6 80 2.03 .146 3.7 9 Blue 42 1.07 .204 5.2 11 Blue 43003195 .399 .418 10.1 10.6 80 2.03 .146 3.7 10 Yellow 42 1.07 .204 5.2 11 Yellow 43001929 .419 .439 10.7 11.1 80 2.03 .146 3.7 10 Black 42 1.07 .204 5.2 11 Black 43009490 .440 .458 11.2 11.6 81 2.06 .146 3.7 11 White 43 1.09 .204 6.4 11 White 43003233 .459 .461 11.7 11.7 84 2.13 .167 4.2 10 Purple 46 1.17 .250 6.4 10 Orange 43003234 .462 .476 11.8 12.0 84 2.13 .167 4.2 10 Purple 46 1.17 .250 6.4 10 Purple 43004061 .477 .503 12.1 12.7 84 2.13 .146 3.7 12 Orange 46 1.17 .250 6.4 10 Orange 43004164 .504 .511 12.8 12.9 84 2.13 .146 3.7 12 Red 46 1.17 .250 6.4 10 Purple 43009922 .512 .536 13.0 13.6 87 2.21 .167 4.2 11 Blue 49 1.24 .250 6.4 11 Blue 43002246 .537 .559 13.7 14.1 87 2.21 .167 4.2 11 Green 49 1.24 .250 6.4 11 Green 43004100 .560 .565 14.2 14.3 87 2.21 .167 4.2 11 Green 49 1.24 .250 6.4 11 Green 43003235 .566 .573 14.4 14.5 92 2.34 .182 4.6 11 Black 54 1.37 .250 6.4 12 Black 43009945 .574 .598 14.6 15.1 92 2.34 .182 4.6 11 Black 54 1.37 .250 6.4 12 White 43009965 .599 .625 15.2 15.8 92 2.34 .182 4.6 12 Brown 54 1.37 .250 6.4 12 Brown 43003239 .626 .632 15.9 16.0 102 2.59 .204 5.2 11 Red 63 1.6 .310 7.9 11 Red 43009760 .633 .666 16.1 16.9 102 2.59 .204 5.2 11 Red 63 1.6 .310 7.9 11 Blue 43004965 .667 .682 17.0 17.3 102 2.59 .204 5.2 12 Yellow 63 1.6 .310 7.9 11 Green 43009947 .683 .710 17.4 18.0 102 2.59 .204 5.2 12 Yellow 63 1.6 .310 7.9 11 Yellow 43004991 .711 .728 18.1 18.4 102 2.59 .204 5.2 12 White 63 1.6 .310 7.9 12 Black 43009868 .729 .744 18.5 18.8 102 2.59 .204 5.2 12 White 63 1.6 .310 7.9 12 White 43006274 .745 .750 18.9 18.9 102 2.59 .204 5.2 12 White 63 1.6 .310 7.9 12 White 43009842 .751 .786 19.0 19.9 102 2.59 .204 5.2 13 White 63 1.6 .310 7.9 12 Brown 43003240 .787 .814 20.0 20.6 111 2.82 .250 6.4 11 Green 72 1.83 .365 9.3 11 Green 43003058 .815 .845 20.7 21.4 111 2.82 .250 6.4 12 Yellow 72 1.83 .365 9.3 11 Yellow 43003028 .846 .855 21.5 21.6 111 2.82 .250 6.4 12 Green 72 1.83 .365 9.3 12 Blue 43003230 .856 .894 21.7 22.6 119 3.02 .250 6.4 12 Black 80 2.03 .365 9.3 12 Black 43003079 .895 .907 22.7 22.9 119 3.02 .250 6.4 12 White 80 2.03 .365 9.3 12 White 43003241 .908 .916 23.0 23.2 119 3.02 .250 6.4 13 Purple 80 2.03 .365 9.3 12 Purple 43003242 .917 .929 23.3 23.5 119 3.02 .250 6.4 13 Brown 80 2.03 .365 9.3 12 Brown 43003243 .930 .942 23.6 23.9 119 3.02 .250 6.4 13 Red 80 2.03 .365 9.3 12 Red 43003244 .943 .977 24.0 24.7 119 3.02 .250 6.4 13 Orange 80 2.03 .365 9.3 13 Orange 430010305 .978 1.016 24.8 25.7 118 3.00 .250 6.4 13 Purple 80 2.03 .365 9.3 12 Purple 430010306 1.017 1.057 25.8 26.8 118 3.00 .250 6.4 14 Red 80 2.03 .365 9.3 12 Red 430010307 1.058 1.079 26.9 27.3 133 3.38 .250 6.4 14 Blue 95 2.41 .365 9.3 13 Blue 430010308 1.080 1.112 27.4 28.1 133 3.38 .250 6.4 14 Green 95 2.41 .365 9.3 13 Green 430010309 1.113 1.149 28.2 29.1 133 3.38 .250 6.4 15 Yellow 95 2.41 .365 9.3 13 Yellow 43003778 1.150 1.190 29.2 30.1 131 3.33 .250 6.4 15 Red 92 2.34 .365 9.3 15 Red 6-19