LWN1601-6 - POWER-ONE

Description

Power One LWN1601-6 Power Converter - AC/DC switching power supply, MELCHER, single output voltage is 24V, adjustment range 7.0V to 26.4V, maximum output current is 10A

Part Number

LWN1601-6

Price

Request Quote

Manufacturer

POWER-ONE

Lead Time

Request Quote

Category

POWER SUPPLY

Specifications

Bump

IEC/EN 60068-2-29, 11 ms; 25 gn

Current limitation

rectangular U/I characteristic; 101 to 112% Io nom

Damp heat

IEC/EN 60068-2-3, 93%, 40°C, 56 days

Degree of protection

IP 20

Electric strength test voltage

class I, I/case 2 kV AC; class I, I/O 3 kV AC; class I, O/case 1 kV AC; class I, O/O 0.35 kV AC

EMC

Electrostatic discharge:IEC/EN 61000-4-2, level 4, contact/air (8/15 kV) criterion A; Electromagnetic field:IEC/EN 61000-4-3, level 3 (10 V/m) criterion A; Electr. fast transients/bursts:IEC/EN 61000-4-4, level 4, capacitive/direct (4/2 kV) criterion A; Surge:IEC/EN 61000-4-5, level 3, in and out, line to line (2 kV), criterion B, level >3, input, line to case (3.5 kV), criterion B, level 2, output, line to case (1 kV), criterion A; Conducted disturbances:IEC/EN 61000-4-6, level 3 (10 V), criterion A; Electromagnetic emissions:CISPR 22/EN 55022, conducted, class A

Hold-up time

Io nom, Uo decreases to 80% of Uo nom typ. 15 ms

Input frequency

14 to 440 Hz

Input fuse

not user accessible 6.3 A, slow blow

Input overvoltage lockout

typ. 105% Ui max

Input reverse polarity

bridge rectifier

Input transient protection

voltage depending resistor (VDR)

Input undervoltage lockout

typ. 80% Ui min

Input voltage

world wide mains, single phase; 85 to 264 V AC; derating information see application note; 90 to 350 V DC

Inrush current

virtually no inrush current

Line and cross regulation

Ui min to Ui max; typ. 50 mV

Load regulation

0 to 100% Io nom, Ui nom; –1.6% Uo nom

Minimum load

not required

MTBF

MIL-HDBK-217E, GB, 40°C, >600,000 h

Operating ambient temperature

Ui nom, Io nom, convection cooled; –40 to 60°C

Operating case temperature Tc

Ui nom, Io nom, –40 to 87°C

Operation in parallel

enabled by droop current share

Output Efficiency

Ui nom, Io nom; up to 89%

Output overvoltage

second control loop, each output, 24 V/48 V; 30/60 V SELV

Output voltage noise

IEC/EN 61204; typ. 50 mV

Output voltage ripple

sinusoidal output ripple at wice the line frequency =1.2 Vpp

Output voltage setting accuracy

Ui nom, Io nom; ± 1.3% Uo nom

Output(s)

no-load, overload and short circuit proof

Overtemperature

reduced output power if thermally overloaded

Pollution degree

AC-in / DC-in 3/2

Power factor

active PFC; up to 0.99

Safety Approvals

EN 60950, UL 1950, CSA22.2 No. 950, UL 508 listed

Shock

IEC/EN 60068-2-27, 11 ms; 50 gn

Shock and vibration

unit wall mounted with brackets

Short term peak power

1 s, electronically controlled; 150% Io nom

Status indication

LED output(s) OK

Storage temperature

non operational, –40 to 100°C

Vibration, random

IEC/EN 60068-2-64, 20 to 500 Hz, 0.05 g2/Hz

Vibration, sinusoidal

IEC/EN 60068-2-6, 10 to 60/60 to 2000 Hz, 0.35 mm/5 gn

Datasheet

LWN1601-6_d-472275287s.pdf

115 KiB

Download

Extracted Text

W Series 125 and 250 Watt AC-DC Converters Input range 85...264 V AC with PFC 1 or 2 isolated, regulated outputs up to 96 V 3 kV AC I/O electric strength test voltage LGA • Electrically and mechanically rugged DIN-rail front end • Outputs individually controlled with 150% output peak power • Operating ambient temperature range –40...60°C with convection cooling Selection chart for front ends 1 Output 1 Output 2 Input voltage Rated power Type Options U I U I U U T = 60°C o nom o nom o nom o nom i min i max A [V DC] [A] [V DC ] [A] P [W] o tot 24.7 5 - - 125 LWR-1601-6 R 24.7 10 - - 250 LWN-1601-6 D1…D5 37 3.3 - - 85...264 VAC 125 LWR 1701-6 S 3 37 6.6 - - (14…440 Hz) 250 LWN 1701-6 M2 49.4 2.6 - - 90…350 VDC 125 LWR 1801-6 F, F1 49.4 5 - - 250 LWN-1801-6 K2 24.7 5 24.7 5 250 LWN-2660-6 49.4 2.5 49.4 2.5 250 LWN 2880-6 Selection chart for battery chargers 1 Output Input voltage Rated power Type Options U I U U T = 60°C o nom o nom i min i max A [V DC] [A] P [W] o tot 25.7...29.3 4.2 85…264 VAC 115 LWR 1240-6 M1 F, F1 25.7...29.3 8.45 3 230 LWN 1240-6 M1 K2 (14…440 Hz) 51.4...58.6 2.1 90…350 VDC 115 LWR 1740-6 M1 51.4...58.6 4.2 230 LWN 1740-6 M1 1 For lead times and minimum order quantity contact Power-One. 2 For availability contact Power-One. 3 Input frequency range certified for 14...440 Hz. For continuous operating frequency <40 Hz and >100 Hz contact factory. www.power-one.com Edition 5/07.2001 1 W Series 125 and 250 Watt AC-DC Converters Input Input voltage world wide mains, single phase 85...264 V AC derating information see application note 90...350 V DC Input frequency 14...440 Hz Power factor active PFC up to 0.99 Inrush current virtually no inrush current Output Efficiency U , I up to 89% i nom o nom Output voltage setting accuracy U , I ± 1.3% U i nom o nom o nom Output voltage noise IEC/EN 61204 typ. 50 mV Output voltage ripple sinusoidal output ripple at wice the line frequency ≤1.2 V pp Line and cross regulation U ...U typ. 50 mV i min i max Load regulation 0...100% I , U –1.6% U o nom i nom o nom Minimum load not required Current limitation rectangular U/I characteristic 101...112% I o nom Short term peak power 1 s, electronically controlled 150% I o nom Operation in parallel enabled by droop current share Hold-up time I , U decreases to 80% of U typ. 15 ms o nom o o nom Control Status indication LED output(s) OK Protection Input fuse not user accessible6.3 A, slow blow Input reverse polarity bridge rectifier Input undervoltage lockout typ. 80% U i min Input overvoltage lockout typ. 105% U i max Input transient protection voltage depending resistor (VDR) Output(s) no-load, overload and short circuit proof Output overvoltage second control loop, each output, 24 V/48 V 30/60 V SELV Overtemperature reduced output power if thermally overloaded Safety Approvals EN 60950, UL 1950, CSA22.2 No. 950, UL 508 listed Electric strength test voltage class I, I/case 2 kV AC class I, I/O 3 kV AC class I, O/case 1 kV AC class I, O/O 0.35 kV AC Pollution degree AC-in / DC-in 3/2 Degree of protection IP 20 www.power-one.com Edition 5/07.2001 2 DIN Rail Mountable W Series EMC Electrostatic discharge IEC/EN 61000-4-2, level 4, contact/air (8/15 kV) criterion A Electromagnetic field IEC/EN 61000-4-3, level 3 (10 V/m) criterion A Electr. fast transients/bursts IEC/EN 61000-4-4, level 4, capacitive/direct (4/2 kV) criterion A Surge IEC/EN 61000-4-5, level 3, in and out, line to line (2 kV) criterion B level >3, input, line to case (3.5 kV) criterion B level 2, output, line to case (1 kV) criterion A Conducted disturbances IEC/EN 61000-4-6, level 3 (10 V) criterion A Electromagnetic emissions CISPR 22/EN 55022, conducted class A Environmental Operating ambient temperature U , I , convection cooled –40...60°C i nom o nom Operating case temperature T U , I –40...87°C C i nom o nom Storage temperature non operational –40...100°C Damp heat IEC/EN 60068-2-3, 93%, 40°C 56 days Shock and vibration unit wall mounted with brackets Shock IEC/EN 60068-2-27, 11 ms 50 g n Bump IEC/EN 60068-2-29, 11 ms 25 g n Vibration, sinusoidal IEC/EN 60068-2-6, 10...60/60...2000 Hz 0.35 mm/5 g n 2 Vibration, random IEC/EN 60068-2-64, 20...500 Hz 0.05 g /Hz MTBF MIL-HDBK-217E, G , 40°C >600'000 h B Options Input and output undervoltage monitoring D1...D5 Output voltage adjustment 10 V...110% of U R o nom Remote on/off S Multi option choice (D1...D5, R, S) via Sub-D connector M1...M2 Built-in second input fuse in the neutral F No fuse fittet (for operation from high DC) F1 System connectors with screw terminals K2 www.power-one.com Edition 5/07.2001 3 W Series 125 and 250 Watt AC-DC Converters Mechanical data Tolerances ±0.3 mm (0.012") unless otherwise indicated. European Projection 118 (4.65") 113.6 (4.47") 105 (4.15") 106.6 (() 4.2") 103 (4.05") 29.4 (1.16") 09107 T C Wall mounting brackets (accessory) Option M 31 (1.22") T T T T A A A Measuring point for case temperature T C www.power-one.com Edition 5/07.2001 4 138 (5.43") 5 15 (0.59") 13 (0.51") 1 43 (1.69") 33 (1.3") 49 (1.93") DIN Rail Mountable W Series Terminal allocation input side S10066 Pin Des. Determination 1 Protective earth 2N Input neutral 1 2 3 3P Input phase Terminal allocation output side S10067 Pin Des. Single output Double output 1 Earth to load Earth to load 2 + Output pos. Output 1 pos. 1 235 4 6 7 8 9 10 11 3 + Output pos. Output 1 pos. 4 – Output neg. Output 1 neg. 5 – Output neg. Output 1 neg. 6 + Output pos. Output 2 pos. 7 + Output pos. Output 2 pos. 8 – Output neg. Output 2 neg. 9 – Output neg. Output 2 neg. 10 Aux. Options Options 11 Earth to load Earth to load Accessories Mounting brackets for vertical chassis/wall mounting Fixing brackets for enhanced vibrations on DIN-rail Protective covers over input and output terminals www.power-one.com Edition 5/07.2001 5 This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products