BLP55 AC-DC Series Data Sheet 55 Watts Features • RoHS lead-free solder and lead-solder-exempted products are available • Industry-standard 3” x 5” footprint • Main output remote sense • CE marked to Low Voltage Directive • Compliance to EN61000-4-2/-3/-4/-5/-6/-8 Description The BLP55 Series’ economical and compact construction provides single or three-output ac-dc power conversion to meet the requirements of networking and data communications systems, as well as commercial and industrial configurations. The BLP55 is rated for convection, as well as forced-air cooling. Full output power is available with external forced-air cooling. Other features include main-output remote sense and an internal EMI filter. Single Output Model Selection MODEL NOMINAL OUTPUT MIN-MAXIMUM OUTPUT MIN-MAXIMUM OUTPUT PEAK OUTPUT TOTAL RIPPLE & NOISE 1 2 3 4 VOLTAGE (VDC) CURRENT, CONVECTION CURRENT CURRENT REGULATION % %p-p BLP55-1005 5V 0 to 8A 0 to 11A 12A ±2 1 BLP55-1012 12V 0 to 3.3A 0 to 4.5A 5A ±2 1 BLP55-1024 24V 0 to 1.6A 0 to 2.3A 2.5A ±2 1 Triple Output Model Selection MODEL NOMINAL OUTPUT MIN-MAXIMUM OUTPUT MIN-MAXIMUM OUTPUT PEAK OUTPUT TOTAL RIPPLE & NOISE 1 2 3 4 VOLTAGE (VDC) CURRENT, CONVECTION CURRENT CURRENT REGULATION % %p-p +5V 0.4 to 4A 0.5 to 5A 7A ±2 1 BLP55-3000 +12V 0.2 to 2A 0.2 to 2.5A 4A ±5 1 -12V 0.0 to 0.5A 0.0 to 0.7A 1 ±5 1 +3.3V 0.5 to 4A 0.5 to 5A 7A ±2.5 1 BLP55-3300 +5V 0.0 to 2A 0.0 to 2.5A 4A ±2.5 1 +12V 0.0 to 0.5A 0.0 to 0.7A 1A ±5 1 1 NOTES: 10 CFM or 150 LFM (average measurement of six equally-distanced points through a 3.5” x 1.6” cross-sectional area) with power supply mounted on 0.25” standoffs. Recommended airflow direction is from the AC side to the DC side. 2 Peak current duration for less than 30 Sec with a maximum duty cycle of 10%. 3 At 25 °C ambient including voltage set point tolerance, line, and load regulation. 4 Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth, and bypass capacitors of 10 μF and 0.1 μF. Ordering Information: OPTIONS SUFFIXES TO ADD TO PART NUMBER RoHS lead solder exempt No RoHS character required. RoHS compliant for all 6 substances Add “G” as the last character of the part number. 103354D Rev AB1, 06-FEB-09 Page 1 of 6 www.power-one.com BLP55 AC-DC Series Data Sheet 55 Watts Input Specifications PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Input Voltage - AC Single-phase continuous input range. 85 100-250 264 VAC Input Voltage - DC Consult factory. Input Frequency AC input. 47 50/60 63 Hz Input Current At 115 VAC input. 1ARMS Inrush Surge Current Internally limited. Vin = 115 VAC, Max Power, 25 °C. 18 APK Internally limited. Vin = 230VAC, Max Power, 25 °C. 36 APK Input Fuse Internally located AC input line fuse rated at F, 250 V, 3.15 A. Efficiency At Max Power, -3300 60% nominal. 70 % Output Specifications PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Output Power With convection cooling (-3300 25 W). See Model Selection Table 40 Watts With forced-air cooling (-3300 41 W). See Model Selection Table 55 Output DC Adjustability: Adjustability of Vo1 (Vo2/Vo3 are not adjustable). -5%, +10% Of Nom Overshoot 5% Load Transient Vo1, Vo2, or Vo3 deviation due to a 50 to 100% load change ±3 % at a rate of 1A/µs. Turn-On Time from AC ON Time required for output voltage to reach within regulation after initial application 1.5 Sec of AC input. Turn-On Delay Time required for output voltage to rise from 10% to 90%. 20 ms Hold-Up Time At 40 W, 115 VAC 20 ms Remote Sense Total compensation for cable losses on Vo1. 500 mV (Remote Sense is not available for Vo2 or Vo3) Interface Signals and Internal Protection PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Overvoltage Protection Main output. 3.3V: 3.8 4.5 5V: 5.7 6.8 12V: 13.8 16.2 V 24V: 27.6 32.4 48V: 52.8 56.4 Short Circuit Protection Fully-protected against output short circuit. 103354D Rev AB1, 06-FEB-09 Page 2 of 6 www.power-one.com BLP55 AC-DC Series Data Sheet 55 Watts Safety, Regulatory, and EMI Specifications PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Agency Approvals UL60950-1/CSA 22.2 No. 60950-1-03. EN 60950-1/IEC 60950-1. CB Approval. CE Mark for LVD. Ground Continuity 40 A Dielectric Withstand Voltage Input-to-Ground (Basic). 1500 VAC 2121 VDC Input-to-Ouput (Reinforced). The primary to secondary test is not performed 3000 VAC on completed assemblies. 4242 VDC Output-to-Ground (Functional). 500 VDC Electromagnetic Interference FCC Part 15. Conducted: B Class CISPR 22 and CISPR 11. Conducted: B ESD Per EN61000-4-2, level 3. Flicker Per EN61000-3-3. Radiated Susceptibility Per EN61000-4-3, level 3. 3 V/m EFT/Burst Per EN61000-4-4, level 3. 1 kV Input Transient Protection Per EN61000-4-5, class 3. Line-to-Line: 1 kV Line-to-Ground: 2 RF Immunity Per EN61000-4-6, level 3. 3 V/m Magnetic Fields Per EN61000-4-8. 1 A/m Leakage Current Per EN60950. BLP55-1XXX At 264 VAC: 0.48 mA BLP55-3XXX AT 264 VAC: 0.72 Environmental Specifications PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Altitude Operating. 10k ASL Ft. Non-Operating. 50k ASL Ft. Operating Temperature 0 °C to 70 °C with linear derating to 50% above 50 °C. Unit will start up at 0 25 70 °C -20 °C but will not meet all published specifications. Storage Temperature -40 85 °C 1 Forced-Air Cooling Forced-air cooling of 150 LFM at 10 CFM is required for full output power. (See Model Selection Table). Convection Cooling When unit is mounted horizontally with free-air convection. 40 W (See Model Selection Table). Temperature Coefficient 0 °C to 70 °C (after 15-minute warm-up). ±0.02 %/°C Relative Humidity Non-Condensing. 5 95 %RH Shock Operating: half-sine 11 ±3ms, 3 axis. 15 G Non-operating: half-sine 11±3ms, 3 axis. 40 Vibration Operating: Random vibration, 5-500 Hz (10 minutes each axis). 2.4 Grms Non-operating: Random vibration, 5-500 Hz (10 minutes each axis). 6.0 Grms 1 NOTES: 10 CFM or 150 LFM (average measurement of six equally-distanced points through a 3.5” x 1.6” cross-sectional area) with power supply mounted on 0.25” standoffs. Recommended airflow direction is from the AC side to the DC side. 103354D Rev AB1, 06-FEB-09 Page 3 of 6 www.power-one.com BLP55 AC-DC Series Data Sheet 55 Watts Figure 1. BLP55-3000 Typical Quasi-Regulation Performance for +12V Output 15 14 5V @ 0A 13 5V @ 1A 5V @ 3A 12 5V @ 5A 11 10 00.5 11.5 22.5 12V Output Current (Amps) Figure 2. BLP55-3000 5V Output Voltage vs. 12V load 5.2 5.1 5V@0A 5 5V@1A 4.9 5V@3A 4.8 5V@5A 4.7 Linear (5V@0A) 4.6 4.5 00.511.522.5 12V Load in Amps 103354D Rev AB1, 06-FEB-09 Page 4 of 6 www.power-one.com 12V Output Voltage (Volts) 5V Voltage BLP55 AC-DC Series Data Sheet 55 Watts Overall Size: 3.00" x 5.00" x 1.23" (76.2mm x 127.0mm x 31.2mm) Weight: 0.51 lb (0.23 kg) CN1 - AC CONN. Mechanical Drawing PIN 1 NEUTRAL (Single-Output Models) PIN 2 MISSING PIN PIN 3 LINE 5.00 (127.0) CN2 - DC CON Ø 0.16 (4 PL) 4.55 (115.6) (4.1) PIN 1 VOUT PIN 2 VOUT PIN 3 VOUT PIN 4 DC COM TOP VIEW PIN #1 PIN 5 DC COM PIN 6 DC COM CN2 - DC OUTPUT CN1 INPUT CONNECTOR CONNECTOR CN3 - REMOTE SENSE.CON (SEE PINOUT 3.00 TABLE) PIN 1 + SENSE (76.2) PIN 2 - SENSE SECONDARY GROUND PIN #1 2.55 (64.8) SAFETY GROUND CONNECTION POINT #2, FASTON TAB, 0.25", 0.03" THICK CN4 FASTENER SAFETY GROUND CLEARANCE AREA CONNECTION POINT #1 (4 PL) 0.27" DIA (6.86) CN3 - REMOTE SENSE PIN #1 CONNECTOR (APPROX. LOCATION) 0.06 (1.5) 1.07 END VIEW 1.23 SIDE VIEW (27.2) (31.2) PRINTED CIRCUIT BOARD 0.1 (2.5) RECOMMENDED MATING CONNECTORS HOUSING PIN CN1 MOLEX 09-50-8031 08-52-0113 LEOCO 3940S030000 3983TCB0000 CN2 MOLEX 09-50-8061 08-52-0113 LEOCO 3940S060000 3983TCB0000 CN3 MOLEX 22-01-3027 08-52-0113 LEOCO 2530S020000 2533TPB0000 NOTE: This is an outline drawing only. The detailed location of components is not shown. 103354D Rev AB1, 06-FEB-09 Page 5 of 6 www.power-one.com BLP55 AC-DC Series Data Sheet 55 Watts Overall Size: 3.00" x 5.00" x 1.23" (76.2mm x 127.0mm x 31.2mm) Weight: 0.51 lb (0.23 kg) Mechanical Drawing CN1 - AC CONN. PIN 1 NEUTRAL (Triple-Output Models) PIN 2 MISSING PIN PIN 3 LINE 5.00 (127.0) CN2 - DC CON Ø 0.16 (4 PL) 4.55 (115.6) (4.1) PIN 1 V2 PIN 2 V1 PIN 3 V1 PIN 4 DC COM TOP VIEW PIN #1 PIN 5 DC COM PIN 6 V3 CN2 - DC OUTPUT CN1 INPUT CONNECTOR CONNECTOR SECONDARY GROUND CN3 - REMOTE SENSE.CON (SEE PINOUT 3.00 TABLE) PIN 1 + SENSE (76.2) PIN 2 - SENSE PIN #1 2.55 (64.8) SAFETY GROUND CONNECTION POINT #2, FASTON TAB, 0.25", 0.03" THICK CN4 FASTENER SAFETY GROUND CLEARANCE AREA CONNECTION POINT #1 (4 PL) 0.27" DIA (6.86) PIN #1 CN3 - REMOTE SENSE CONNECTOR (APPROX. LOCATION) 0.06 (1.5) 1.07 END VIEW 1.23 SIDE VIEW (27.2) (31.2) PRINTED CIRCUIT BOARD 0.1 (2.5) RECOMMENDED MATING CONNECTORS HOUSING PIN CN1 MOLEX 09-50-8031 08-52-0113 LEOCO 3940S030000 3983TCB0000 CN2 MOLEX 09-50-8061 08-52-0113 LEOCO 3940S060000 3983TCB0000 CN3 MOLEX 22-01-3027 08-52-0113 LEOCO 2530S020000 2533TPB0000 NOTE: This is an outline drawing only. The detailed location of components is not shown. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 103354D Rev AB1, 06-FEB-09 Page 6 of 6 www.power-one.com