control site PRODUCT SPECIFICATION CM9760-VCRC Series VCR Controller CONTROLS SANYO, SONY, AND PELCO VCRS Product Features • Controls up to 64 VCRs • Expansion Via Daisy-chaining Allows 39 VCRC-Ps to Control up to CM9760-VCRC (FRONT) 2,496 Pelco VCRs from a Single Sercom Port on the CM9740-CC1 or CM9760-CC1 • Expansion Via Daisy-chaining Allows 11 VCRCs to Control up to 704 Sony* or Sanyo* VCRs from a Single Sercom Port on the CM9740-CC1 or CM9760-CC1 • Operates Seven VCR Control Functions Automatically or Manually CM9760-VCRC (BACK) • 100-240 VAC Auto-ranging Power Supply • For Rack Mount Use Only; Occupies One Rack Unit (1.75 inches or 4.45 cm) * Sanyo SRT672 and the SRC-800. Also Sony models with resistive ladder control can be used. In addition, Sony S-link VCRs (VHS standard only) such as the SLV-775HF or the SVO-1320 are compatible. ™ Pelco VCR controllers connect directly to the System 9740 or Sys- 17.40 ® (44.20) tem 9760 controller and give security and surveillance operators the ability to control appropriate VCR models automatically or man- ually from the system. Compatible VCRs are speciŢc to each VCR controller type. The 8.11 CM9760-VCRC remotely controls VCRs that use either resistive lad- (20.60) der remote control or S-link remote control. Suitable models of Sanyo VCRs that can be controlled with the resistive ladder method are the SRT672 and the SRC-800. Also Sony models with resistive ladder control can be used. In addition, Sony S-link VCRs (VHS standard only) such as the SLV-775HF or the SVO-1320 will work with the VCRC. The CM9760-VCRC-P is for use with Pelco’s TLR2096, TLR2168, TLR3096, and TLR3168 VCRs and employs the resistive lad- 19.00 der remote control method. (48.26) 1.75 VCR hookup to the VCRC is easily done with optional control cables (4.45) available from Pelco. ConŢguration and setup of the VCRC is accomplished by setting DIP NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; switches located behind the front panel of the unit. ALL OTHERS ARE INCHES. Up to 64 VCRs can be attached to and controlled by any VCR control- ler. The seven VR control functions (play, stop, fast forward, reverse, pause, record, and eject) can be initiated by a combination of matrix keyboard control commands and/or appropriate macro commands. DataFAX SPEC: 21941 MANUAL: 219416 (CM9760-VCRC), 219436 (CM9760-VCRC-P) International Organization for Standardization; ® C1941 / REVISED 10-01 Registered ISO 9001 TECHNICAL SPECIFICATIONS MODELS CERTIFICATIONS/RATINGS CM9760-VCRC VCR control unit capable of controlling • CE, Class B (CM9760-VCRC, CM9760-VCRC-P, and CM9760-VCRC-TX) 64 VCRs. VCRC only controls speciŢc Sanyo • FCC, Class B device (CM9760-VCRC and CM9760-VCRC-P) and Sony models. • Meets NEMA Type 1 standards CM9760-VCRC-P VCR control unit capable of controlling 64 Pelco VCRs. VCRC-P controls only Pelco OPTIONAL ACCESSORIES models TLR2096, TLR2168, TLR3096, and CM9760-VCRC-TX VCR control cable (1/8-inch jack on one end TLR3168 VCRs. and bare leads on other end) for connecting speciŢc Sanyo and Sony model VCRs to the ELECTRICAL CM9760-VCRC controller, 15-foot (4.5 m) Input Voltage 100-240 VAC, 50/60 Hz, auto-ranging length Power 30 VA CM9760-VCRC-C20 Same as CM9760-VCRC-TX except 20-foot Data Ports (6.1 m) length Input RS-422, RJ-45 connector CM9760-VCRC-C50 Same as CM9760-VCRC-TX except 50-foot DIP switch selectable baud rate (15.2 m) length Output RS-422, RJ-45 connector CM9760-VCRC-PTX VCR control cable (1/8-inch jack to bare leads) DIP switch for selecting baud rate for connecting Pelco model TLR2096 VCR to DB9 connector (factory use only) the CM9760-VCRC controller. 50-foot (15.2 m) Fusing 500 mA, 250 V length. Relay Out Load rating for relay contacts: 0.50A at 125 VAC or 1A at 24 VDC MECHANICAL Connectors VCRC Input Four dual-header, 32-input connectors with mating plugs Power 3-wire, 18 AWG RS-422 Two RJ-45 connectors RS-232 One DB9 connector Relay Out One 3-pin header with mating plug GENERAL Operating Temperature 32° to 122°F (0° to 50°C) Construction Aluminum Finish Black polyester powder coat Dimensions 1.75" H x 19.00" W x 8.11" D (1 RU) (4.45 x 48.26 x 20.6 cm) Mounting Fits 19-inch EIA Standard rack Unit Weight 7.45 lb (3.38 kg) Shipping Weight 12 lb (5.44 kg) Pelco Worldwide Headquarters: ® System 9760 is a registered trademark of Pelco. 3500 Pelco Way, Clovis, California 93612-5699 USA ™ System 9740 is a trademark of Pelco. USA & Canada Tel: (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108 SpeciŢcations subject to change without notice. International Tel: (559) 292-1981 • FAX (559) 348-1120 • DataFAX (559) 292-0435 ©Copyright 2001, Pelco. All rights reserved. ® www.pelco.com