ADDENDUM Addendum No. C1573M Date February 1, 2006 Manuals Affected C1572M, C1555M-F, C1566M-C Manual Update The front and rear mounting rails and the mounting brackets are no longer supplied with the CM9700-CC1. Disregard the CM9700-CC1 mounting information in the above referenced manuals. To mount the CM9700-CC1 into a standard 19-inch EIA rack follow these instructions: 1. Insert the CM9700-CC1 into the rack. 2. Tighten the CM9700-CC1 to the rack using the four supplied Phillips screws with washers. RACK CM9700-CC1 (4) SCREWS, 10-32 X 0.750-INCH PHILLIPS, PAN HEAD WITH WASHERS Figure 1. Mounting the CM9700-CC1 Pelco Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com USA & Canada •Tel: 800/289-9100 • Fax: 800/289-9150 International •Tel: 1-559/292-1981 • Fax: 1-559/348-1120 INSTALLATION/OPERATION ® System 9760 Video Matrix Switching Control System C1572M (9/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 CPU Controller and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Matrix Bay and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Network Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Optional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Compatible Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 System Setup Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Unpacking the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Unpacking the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Installing the CM9700-CC1 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Selecting a Location for the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Mounting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Connecting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Powering On the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Installing CM9760-MXB Matrix Bay(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Selecting a Location for the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Mounting the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Verifying CM9760-MXB Component Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Connecting the CM9760-MXB to the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Connecting Power to the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Powering On the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Checking Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Connecting Video Inputs and Video Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Verifying System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 CM9700-CC1 Component Installation or Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Removing the CM9700-CC1 Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Installing or Replacing a CM9700-SER Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 CM9760-MXB Component Installation or Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Installing or Replacing Rear Panel Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Installing or Replacing a CM9760-RPC Rear Panel Input Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Installing or Replacing a CM9760-RPL Rear Panel Looping Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Installing or Replacing a CM9760-DFC Downframe Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Installing or Replacing a CM9760-DFL Downframe Looping Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Installing or Replacing a CM9760-RPM Rear Panel Output Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Installing or Replacing a CM9760-VCC Video Input Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Installing a CM9760-VCC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Replacing a CM9760-VCC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Installing or Replacing a CM9760-VMC Video Output Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Installing a CM9760-VMC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Replacing a CM9760-VMC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Installing a CM9760-VMM Video Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Installing or Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Installing a Backup Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Replacing a Power Supply Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Enabling/Disabling the Power Supply Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 System Programming Using DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Performing System 9760 DOS Programming Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Copying Configuration Files from the CM9700-MGR to the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 C1572M (9/05) 3 Setting and Adjusting System Time in a Single-Node System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Setting and Adjusting System Time in a Multi-Node System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 DOS Filename Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 DOS Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Monitoring CM9700-CC1 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Viewing Monitor Box Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Allocating Monitors to Monitor Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Entering CM9700-CC1 PC Keyboard Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Viewing Multi-Node System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Entering CM9700-NW1 PC Keyboard Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 General Troubleshooting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Troubleshooting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Troubleshooting the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 CM9700-CC1 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Directory Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 9700 Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 TESTPORT Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 DOS Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 CM9760-MXB Matrix Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Functional System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Video Input and Output Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 CM9760-VCC Video Input Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 CM9760-VMC Video Output Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Rear Panel Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 CM9760-RPC Rear Panel Input Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 CM9760-RPL Rear Panel Looping Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 CM9760-RPM Rear Panel Output Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 CM9760-DFC Rear Panel Downframe Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 CM9760-DFL Rear Panel Downframe Looping Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 Sideframing and Downframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Sideframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Downframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 Using a Combination of Sideframing and Downframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Downframing to the CM9760-MXBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CM9700-CC1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CM9760-MXB Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Appendix A. CM9700-CC1 ASCII Protocol Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 ACD to CM9700-CC1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Connecting an ACD DB9 Port to a CM9700-CC1 DB9 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Connecting an ACD DB9 Port to a CM9700-CC1 RJ-45 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 ASCII Protocol Commands Supported by the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Appendix B. CM9760-MXB Sideframe and Downframe Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 Sideframe-Only Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Downframe-Only Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Sideframe and Downframe Combination Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 CM9760-MXBL Downframe Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 4 C1572M (9/05) List of Illustrations 1 Basic Components of a 9760 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 Mounting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 3 CM9700-CC1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 4 CM9700-MGR PC to CM9700-CC1 Null Modem Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 5 Sample Port Assignment Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 6 Mounting the CM9760-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 7 Sample Downframe Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 8 CM9760-MXB Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 9 Sample CM9760-MXB ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 10 CM9760-MXB to CM9700-CC1 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 11 CM9760-MXB Power Connections (Two Power Supplies Installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 12 CM9760-VCC and CM9760-VMC Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 13 Fuse Locations on CM9760-VCC and CM9760-VMC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 14 CM9760-MXB Video Input and Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 15 CM9700-CC1 Top Cover Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 16 CM9700-CC1 with Top Cover Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 17 Sample CM9700-SER Card Jumper Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 18 Termination Jumpers on CM9760-RPC Rear Panel Input Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 19 CM9760-RPC Rear Panel Input Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 20 Termination Jumpers on CM9760-RPL Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 21 CM9760-RPL Rear Panel Looping Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 22 Termination Jumpers on CM9760-DFC Downframe Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 23 CM9760-DFC Downframe Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 24 Termination Jumpers on CM9760-DFL Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 25 CM9760-DFL Downframe Looping Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 26 Termination Jumpers on CM9760-RPM Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 27 CM9760-RPM Rear Panel Output Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 28 CM9760-VCC Video Input Card Installation (Slots 1-16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 29 DIP Switch and Jumper Locations on CM9760-VMC Video Output Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 30 CM9760-VMC Video Output Card Installation (Slot 17). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 31 CM9760-VMM Video Output Module Locations (CM9760-VMC8 Video Output Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 32 CM9760-MXB Backup Power Supply Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 33 CM9760-MXB Power Supply Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 34 CM9760-MXB Power Supply Alarm Jumper Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 35 Sample CM9700-CC1 Diagnostic Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 36 Sample Monitor Box on CM9700-CC1 Diagnostic Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 37 Sample CM9700-NW1 Diagnostic Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 38 CM9700-CC1 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 39 CM9700-CC1 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 40 CM9700-CC1 Rear Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 41 CM9700-CC1 Root Directory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 42 CM9700-CC1 9700 Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 43 CM9700-CC1 TESTPORT Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 44 Video Signal Flow through the Matrix Bay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 45 CM9760-MXB Front View (Front Panel Removed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 46 CM9760-MXB Rear View (Single-Bay ConŢguration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 47 CM9760-MXB Alarm Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 48 CM9760-VCC Video Input Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 49 CM9760-VMC Video Output Card (CM9760-VMC16). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 50 CM9760-RPC Rear Panel Input Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 51 CM9760-RPL Rear Panel Looping Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 52 CM9760-RPM Rear Panel Output Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 53 CM9760-DFC Downframe Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 54 CM9760-DFL Downframe Looping Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 55 Matrix Bay Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 56 CM9760-MXB Sideframing Example: 496 Video Inputs and 16 Video Outputs (496 x 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 57 CM9760-MXB Downframing Example: 256 Video Inputs and 32 Video Outputs (256 x 32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 58 CM9760-MXB Sideframing and Downframing Example: 496 Video Inputs and 32 Video Outputs (496 x 32) . . . . . . . . . . . . . . . . . . . . . . . .107 59 Downframing to CM9760-MXBL Example: 256 Video Inputs and 16 Video Outputs (256 x 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 C1572M (9/05) 5 60 ACD DB9 to CM9700-CC1 DB9 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 61 ACD DB9 to CM9700-CC1 RJ-45 Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 62 Sideframing: 736 x 16 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 63 Sideframing: 976 x 16 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 64 Downframing: 256 x 48 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 65 Downframing: 256 x 48 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 66 Downframing: 256 x 64 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 67 Downframing: 256 x 64 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 68 Sideframing and Downframing: 496 x 32 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 69 Sideframing and Downframing: 496 x 48 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 70 Sideframing and Downframing: 496 x 48 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 71 Sideframing and Downframing: 496 x 64 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 72 Sideframing and Downframing: 496 x 64 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 73 Sideframing and Downframing: 736 x 32 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 74 Sideframing and Downframing: 736 x 32 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 75 Sideframing and Downframing: 736 x 48 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 76 Sideframing and Downframing: 736 x 48 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 77 Sideframing and Downframing: 736 x 64 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 78 Sideframing and Downframing: 736 x 64 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 79 Sideframing and Downframing: 976 x 32 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 80 Sideframing and Downframing: 976 x 32 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 81 Sideframing and Downframing: 976 x 48 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 82 Sideframing and Downframing: 976 x 48 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 83 Sideframing and Downframing: 976 x 64 ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 84 Sideframing and Downframing: 976 x 64 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 85 Downframing to CM9760-MXBL: 496 x 16 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 86 Downframing to CM9760-MXBL: 736 x 16 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 87 Downframing to CM9760-MXBL: 976 x 16 ConŢguration, Looping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 List of Tables A RS-422 SERCOM Port Connections in a Single-Node System with a CM9760-HS Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 B RS-422 SERCOM Port Connections in a Single-Node System without a CM9760-HS Hot Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 C SERCOM Port Connections in a Networked System with a CM9760-HS Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 D SERCOM Port Connections in a Networked System without a CM9760-HS Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 E CM9700-SER Card Jumper Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 F CM9760-VCC Slot Positions and Corresponding Physical Input Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 G S2 DIP Switch Functions and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 H X55 Video Standards and Associated Jumper Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 I DOS Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 J CM9700-CC1 PC Keyboard Command Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 K CM9700-NW1 PC Keyboard Command Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 L CM9700-CC1 Hardware Error Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 M CM9700-CC1 System Error Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 N Troubleshooting Using CM9760-MXB Diagnostic LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 O ASCII Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 P ASCII Command Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Q ASCII Command Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 6 C1572M (9/05) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliŢers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not Ţt into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories speciŢed by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table speciŢed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Refer all servicing to qualiŢed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Apparatus shall not be exposed to dripping or splashing and that no objects Ţlled with liquids, such as vases, shall be placed on the apparatus. 15. WARNING: To reduce the risk of Ţre or electric shock, do not expose this apparatus to rain or moisture. 16. Installation should be done only by qualiŢed personnel and conform to all local codes. 17. Unless the unit is speciŢcally marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 18. Use only installation methods and materials capable of supporting four times the maximum speciŢed load. 19. A readily accessible disconnect device shall be incorporated in the building installation wiring. 20. The socket-outlet shall be installed near the equipment and shall be easily accessible. 21. A CCC-approved power cord must be used to power this equipment when used in China. CAUTION: These servicing instructions are for use by qualiŢed service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualiŢed to do so. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions provided by the battery manufacturer. Only use replacement parts recommended by Pelco. The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. CAUTION: This symbol indicates that there are important operating and maintenance instructions RISK OF ELECTRIC SHOCK. DO NOT OPEN. in the literature accompanying this unit. C1572M (9/05) 7 Regulatory Notices CM9700-CC1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. You may also Ţnd helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing OfŢce, Washington D.C. 20402. Changes and ModiŢcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules. In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. CM9760-MXB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes and ModiŢcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules. In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 8 C1572M (9/05) System Overview ® This section provides an overview of the System 9760 video matrix switching control system, hereinafter referred to simply as the 9760 system. The following information is provided: • Description of the basic components of the 9760 system • Summary listing of 9760 system device models and compatible equipment DESCRIPTION The 9760 system allows control and monitoring of up to 2,048 video input devices (for example, cameras) and 512 video output devices (for example, monitors). The 9760 system consists of the following basic components (refer to Figure 1): • CM9700-CC1 central processing unit (CPU): Controls system operation and therefore is also commonly referred to as the controller. Connects to a wide variety of peripheral equipment. Detailed information about the CM9700-CC1 is provided in this manual. • CM9760-MXB matrix bay: Performs all video switching functions as directed from the CM9700-CC1. Connects to a maximum of 256 video input devices and 16 video output devices. Detailed information about the CM9760-MXB is provided in this manual. • CM9760-KBD keyboard: Provides the user interface to system operations. Detailed information about the CM9760-KBD is provided in the CM9760-KBD/KBR Keyboard Installation/Operation manual. • CM9700-MGR system management software: Allows easy system setup and conŢguration and therefore is also commonly referred to as the System Manager. Requires installation on a PC that meets CM9700-MGR system requirements. Detailed information about the CM9700-MGR software and PC system requirements is provided in the CM9700-MGR Software Guide. CM9700-MGR CM9760-KBD CM9700-CC1 CAMERA 1 MONITOR 1 CM9760-MXB MONITOR 16 CAMERA 256 Figure 1. Basic Components of a 9760 System NOTE: If your 9760 system includes a CM9760-CC1 that is running version 8.03.xxx or earlier software and you are using CM9760-MGR software, refer to the CM9760-CC1 and CM9760-MGR documentation provided with your system. In addition to the basic components, you can also use peripheral devices in the 9760 system. Peripheral devices include equipment such as KBD300A/KBD200A keyboards, CM9760-MDA master distribution ampliŢers, CM9760-ALM alarm interface units, CM9760-REL relay interface ® ® units, Genex multiplexers, and Pelco VCRs. C1572M (9/05) 9 Note the following: • To ensure uninterrupted operation, the 9760 system can be equipped with a backup CM9700-CC1 by means of a CM9760-HS hot switch. For detailed information about the CM9760-HS, refer to the CM9760-HS Hot Switch Installation/Operation manual. • The CM9700-NW1, commonly referred to as the network interface unit (NIU), can be used to connect two or more CM9700-CC1 units to create a networked system. Each CM9700-CC1 unit and attached devices comprise a node in the network. For detailed information about the CM9700-NW1, refer to the System 9760 Networking Guide. • You can increase video output capacity of a single node from 128 to a maximum of 512 by using CM9760-MDA units. For detailed information about the CM9760-MDA, refer to the CM9760-MDA Master Distribution AmpliŢer Installation/Operation manual. MODELS The following provides a list of models of 9760 system devices and compatible equipment. CPU CONTROLLER AND COMPONENTS CM9700-CC1 CPU controller. Operates on 120 VAC, 60 Hz or 230 VAC, 50 Hz. CM9700-SER Serial communication (SERCOM) card (RS-422). Provides 8 SERCOM ports to interface peripheral equipment (4 cards maximum per CM9700-CC1). CM9700-SER-32 Port expansion unit. Provides 32 SERCOM ports. Includes interconnecting cables and adapters for DB9 and RJ-45 connectors. Data interface can be RS-232 or RS-422. Up to 3 units can be added to a CM9700-CC1. (Check with Pelco Systems Applications Department before adding to an existing CM9700-CC1.) MATRIX BAY AND COMPONENTS CM9760-MXB Video matrix bay equipped with CM9760-MPS power supply. Operates on 120 VAC, 60 Hz. CM9760-MXB-X Same as CM9760-MXB except operates on 230 VAC, 50 Hz. CM9760-MXBL Video matrix bay for use with CM9760-DFL downframe looping cards. No power required. CM9760-MPS Matrix bay power supply (spare). Operates on 120 VAC, 60 Hz. CM9760-MPS-X Matrix bay power supply (spare). Operates on 230 VAC, 50 Hz. CM9760-RPC Rear panel input card. Provides 16 BNC connectors to connect video inputs to matrix bay. CM9760-RPL Double-wide rear panel card for single-bay looping. Reduces maximum number of inputs to 128. CM9760-DFC Downframe rear panel card and cable assembly. Connects multiple matrix bays for expansion purposes. CM9760-DFL Downframe rear panel card and cable assembly with BNC connectors for looping video. CM9760-VCC Video input card capable of accepting up to 16 video inputs. Also requires a rear panel card (CM9760-DFC, CM9760-DFL, or CM9760-RPC, or CM9760-RPL). CM9760-RPM Rear panel output card. Provides 16 BNCs to connect video outputs to matrix bay. Also interfaces video output signals from CM9760-VMC4, CM9760-VMC8, CM9760-VMC12, or CM9760-VMC16 video output card. CM9760-VMC4 Video output card providing 4 video outputs. Requires CM9760-RPM. CM9760-VMC8 Video output card providing 8 video outputs. Requires CM9760-RPM. CM9760-VMC12 Video output card providing 12 video outputs. Requires CM9760-RPM. CM9760-VMC16 Video output card providing 16 video outputs. Requires CM9760-RPM. CM9760-VMM Video output module. Expands outputs of CM9760-VMC4, CM9760-VMC8, and CM9760-VMC12 video output cards. KEYBOARDS CM9760-KBD* Full-function desktop variable-speed keyboard. Operates on 120 VAC, 60 Hz. CM9760-KBD-X* Same as CM9760-KBD except operates on 230 VAC, 50 Hz. CM9760-KBR* Full-function 19-inch EIA rack mount keyboard. Operates on 120 VAC, 60 Hz. CM9760-KBR-X* Same as CM9760-KBR except operates on 230 VAC, 50 Hz. KBD300A Desktop keyboard with full switching capabilities plus joystick control of PTZ functions. Operates on 12 VAC or ±12 VDC. (Requires KBDKIT for power.) KBD200A Desktop keyboard with full switching capabilities plus push-button control of PTZ functions. Operates on 12 VAC or ±12 VDC. (Requires KBDKIT for power.) *Software version 8.03 or higher is required. 10 C1572M (9/05) NETWORK INTERFACE UNIT CM9700-NW1 Network CPU and software necessary for joining two or more independent systems together. Allows multiple systems to share video and control. Commonly referred to as the network interface unit (NIU). OPTIONAL COMPONENTS CM9760-ALM Alarm interface unit. Connects directly to each system. Each unit can monitor up to 64 alarms. Up to four units can be connected in a series from one SERCOM port. CM9760-CDU-T Code distribution unit. Sixteen-channel RS-422 transmit-only (two data wires and ground) distributor. Primarily used for wiring up to 16 pan/tilt/zoom receivers in a “star” conŢguration. ® CM9760-CXTA Coaxitron translator. Generates Coaxitron signals for Pelco Coaxitron receivers. Each translator supports up to 16 receivers. CM9760-DMR Data merger and port expander unit. Allows multiple CM9700-CC1 units to control multiple pan/tilt/zoom cameras and allows multiple keyboards to communicate through one CM9700-CC1 port. CM9760-DMR-X Same as CM9760-DMR except operates on 230 VAC, 50 Hz. CM9760-HS Hot switch interface unit. Changeover unit that monitors the status of a primary CM9700-CC1 in the system. CM9760-MDA Master distribution ampliŢer. Inserts master time and date from the CM9700-CC1 and a programmable title of up to 24 characters on 1 to 16 video signals. CM9760-MDA-X Same as CM9760-MDA except operates on 230 VAC, 50 Hz. CM9760-REL Relay interface unit. Connects directly to each system and provides dry contact switching for direct or automatic control of peripheral equipment. Each unit provides up to 64 SPST contact outputs. CM9760-VCRC Series VCR controllers capable of controlling 64 VCRs. Genex Multiplexers Genex Series MX4009 (9-channel) and MX4016 (16-channel) multiplexers. VMX200 and Video management systems. Graphical map/icon-based user interface for mouse-driven operator control from VMX300 Series external PC. COMPATIBLE RECEIVERS ® Spectra Series Spectra dome multiple protocol receiver. ERD97P21-U Pelco P-protocol receiver. ® LRD41C21-1/-2/-3 Legacy Ţxed speed receiver with presets. LRD41C22-1/-2/-3 Same as LRD41C21 Series except variable speed receiver. ® Esprit Integrated pan/tilt positioning receiver. ™ ExSite Integrated pan/tilt explosionproof positioning receiver. Coaxitron Coaxitron translator allows Coaxitron control of PTZ cameras. C1572M (9/05) 11 System Setup This section provides information about the following: • Overview of tasks necessary to set up a 9760 system • Unpacking the CM9700-CC1 controller and CM9760-MXB matrix bay • Installing the CM9700-CC1 controller • Installing CM9760-MXB matrix bay(s) • Verifying system operation SYSTEM SETUP OVERVIEW The following provides an overview of the tasks necessary to set up a 9760 system and prepare the system for operation. It is recommended that you perform the tasks in the order listed below. NOTE: For detailed instructions to perform the tasks listed below for setup of the CM9700-CC1 and CM9760-MXB, refer to the Unpacking, Installing the CM9700-CC1 Controller, and Installing CM9760-MXB Matrix Bay(s) sections in this manual. For detailed instructions to perform the tasks listed below for setup of all other devices in your system, refer to the manual provided for the device. 1. Unpack all equipment. Verify delivery according to the packing slip. Keep all manuals and cables with the associated equipment. 2. Select a location within a standard 19-inch (48.26 cm) EIA rack for each device to be mounted. 3. Mount each device into the selected location within a rack. DANGER: When mounting equipment into a rack, always install equipment starting from the bottom of the rack. Installing equipment starting from the top of the rack can cause the rack to topple. 4. Verify that the correct number of cards and power supplies have been installed in each CM9760-MXB in the system according to the system order. 5. Install the CM9700-MGR software on a PC, and then do the following: a. Copy the startconŢg.psm Ţle from the CM9700 Factory ConŢguration Data CD. b. Open the startconŢg.psm Ţle using the CM9700-MGR. NOTES: • The CM9700-MGR software is contained on the CM9700 Resource CD, which is provided in the System 9760 binder. For CM9700-MGR software installation instructions, refer to the CM9700-MGR Software Guide, which is also provided in the System 9760 binder. • The CM9700 Factory ConŢguration Data CD is provided in the System 9760 binder. • Do not modify the system using the CM9700-MGR until after you have veriŢed system operation in step 12 below. 6. Connect all system devices to the CM9700-CC1 according to the CM9700-CC1 port assignments listed in the System 9760 port assignment table. NOTE: The System 9760 port assignment table, titled “System 9760 Factory Default Port Settings,” is provided in the System 9760 binder. Detailed information about the System 9760 port assignment table is provided in the Installing the CM9700-CC1 Controller section in this manual. 7. Connect power cabling to all devices. 8. Power on all devices connected to the CM9700-CC1. 9. Power on the CM9700-CC1. 10. Check diagnostic LEDs on devices to ensure that the devices are operating properly. 11. Connect all other cabling—for example, video input and output cabling—to all devices as appropriate. 12. Verify system operation (refer to the Verifying System Operation section in this manual). 12 C1572M (9/05) UNPACKING Various items are supplied with the CM9700-CC1 and with the CM9760-MXB. Refer to the Unpacking the CM9700-CC1 and Unpacking the CM9760-MXB sections for a list of items supplied with the units. UNPACKING THE CM9700-CC1 The following items are supplied with the CM9700-CC1: 1 CM9700-CC1 unit, with front rack ears installed 1 120 VAC, 60 Hz power cord (USA standard) 1 230 VAC, 50 Hz power cord (European standard) 1 Keyboard, PS/2 1 PS/2-to-AT keyboard adapter 1 BNC extraction tool 2 Brackets with a set of 6 screws, 8-32 x 0.250-inch, pan head 2 Adjustable support rail sets (each set includes 1 front-mounting rail and 1 rear-mounting rail) and the following sets of screws: 6 Screws, 8-32 x 0.375-inch, pan head with washers 12 Screws, 10-32 x 0.375-inch, ţat head 4 Screws, 10-32 x 0.750-inch, Phillips, pan head with washers 6 Screws, 8-32 x 0.250-inch, Phillips, pan head UNPACKING THE CM9760-MXB The following items are supplied with the CM9760-MXB: 1 CM9760-MXB matrix bay, with front rack ears installed 1 Power cord: – For the CM9760-MXB: 120 VAC, 60 Hz power cord (USA standard) – For the CM9760-MXB-X: 230 VAC, 50 Hz power cord (European standard) NOTE: If the matrix bay is shipped with two power supplies installed, then two 120 VAC or 230 VAC power cords are supplied. 1 RJ-45 reversed data cable 8 Screws and washers for mounting the bay 1 Sheet of video input number labels that can be afŢxed to the rear panel BNC cards to correspond to video input numbers In addition, one CM9760-VMC video output card, the appropriate number of CM9760-VCC video input cards, associated rear panel cards, and up to two power supplies are installed in the matrix bay according to your system order. C1572M (9/05) 13 INSTALLING THE CM9700-CC1 CONTROLLER Installation of the CM9700-CC1 includes the following tasks: • Selecting a location for the CM9700-CC1 in a standard EIA rack • Mounting the CM9700-CC1 • Connecting the CM9700-CC1 • Powering on the CM9700-CC1 To perform each of the above tasks, refer to the sections that follow. SELECTING A LOCATION FOR THE CM9700-CC1 The CM9700-CC1 is designed to be mounted into a standard 19-inch (48.26 cm) EIA rack. When selecting a location in a rack for the CM9700-CC1, note the following: • The CM9700-CC1 occupies 4 RUs or 7 inches (17.78 cm) of vertical rack space. • The maximum distance allowable between the CM9700-CC1 and a CM9760-MXB is 4,000 feet (1,219 meters). • Allow at least 1 RU or 1.75 inches (4.5 cm) of space above the CM9700-CC1 for air circulation. MOUNTING THE CM9700-CC1 Brackets and support rails are provided to mount the CM9700-CC1 into a rack. The brackets and support rails are provided for your convenience but are not required. To mount the CM9700-CC1 without the brackets and support rails, fasten each rack ear of the CM9700-CC1 to the rack using two 10-32 x 0.750-inch Phillips pan head screws and washers for each ear. To mount the CM9700-CC1 using the supplied brackets and support rails, refer to Figure 2 and perform the following steps: 1. Attach one bracket to each side of the CM9700-CC1 using three 8-32 x 0.250-inch pan head screws for each side. Attach each bracket so that the slotted holes in the bracket are positioned toward the front of the CM9700-CC1 and the tapered ends of the bracket are positioned toward the rear of the CM9700-CC1. 2. For each set of support rails, attach the front-mounting support rail to the rear-mounting support rail using three 8-32 x 0.375-inch pan head screws and washers for each set. Leave the screws loose until the support rails are attached to the rack. 3. Attach one set of support rails to the equipment rack in the desired location as follows: a. Position the ear of the front-mounting support rail against the front of the equipment rack and align the holes in the ear of the rail with the threaded holes in the rack. Attach the ear of the rail to the rack using two 10-32 x 0.375-inch ţat head screws. b. Adjust the support rails to the correct depth of the equipment rack by sliding the rear-mounting support rail to the back of the equipment rack. c. Attach the ear of the rear-mounting support rail to the rear of the equipment rack using four 10-32 x 0.375-inch ţat head screws. (The holes in the ear of the rail should align with the threaded holes in the equipment rack.) 4. Tighten the three 8-32 x 0.375-inch pan head screws and washers that were attached to the front- and rear-mounting support rails in step 2 above. 5. Repeat steps 3 and 4 for the second set of support rails. 6. Place the CM9700-CC1 onto the support rails and slide the unit into the rack. The CM9700-CC1 should slide in and out of the rack easily. DANGER: When sliding the CM9700-CC1 out of the rack, be careful not to let the unit fall out of the rack. 7. Fasten each rack ear of the CM9700-CC1 to the equipment rack using two 10-32 x 0.750-inch Phillips pan head screws and washers for each ear. 14 C1572M (9/05) (8) SCREWS, REAR MOUNTING 10-32 X 0.375-INCH SUPPORT RAIL FLAT HEAD FRONT MOUNTING SUPPORT RAIL (6) SCREWS, 8-32 X 0.375-INCH PAN HEAD WITH WASHERS RACK (4) SCREWS 10-32 X 0.375-INCH FLAT HEAD BRACKET (SIDE VIEW) CM9700-CC1 (6) SCREWS, 8-32 X 0.250-INCH PAN HEAD (3 EACH SIDE) (4) SCREWS, 10-32 X 0.750-INCH PHILLIPS, PAN HEAD WITH WASHERS SLOTTED HOLES TAPERED ENDS TOWARDS FRONT TOWARDS REAR OF UNIT OF UNIT Figure 2. Mounting the CM9700-CC1 C1572M (9/05) 15 CONNECTING THE CM9700-CC1 System 9760 devices and other equipment connect to the rear panel of the CM9700-CC1 (refer to Figure 3). CM9700-MGR PC VGA MONITOR CM9700-CC1 36 28 20 12 35 27 19 11 RS-422 SERCOM PORT 34 26 18 10 CONNECTIONS 33 25 17 9 32 24 16 8 POWER CORD 31 23 15 7 30 22 14 6 PRINTER COM1 COM2 29 21 13 5 PS/2 KEYBOARD Figure 3. CM9700-CC1 Connections As illustrated in Figure 3, CM9700-CC1 connections include the following: • CM9700-MGR PC (RS-232 serial communication) • VGA monitor • PS/2 keyboard (supplied) • System devices for RS-422 serial communication (for example, matrix bays, keyboards, and pan/tilt or dome receivers) • Power cord (supplied) For detailed information about each of the above connections, refer to the sections that follow. NOTE: For detailed information about connecting ASCII communication devices to the CM9700-CC1, refer to Appendix A. Connecting the CM9700-MGR PC to the CM9700-CC1 NOTES: • It is recommended that you install the CM9700-MGR software on the PC before connecting the PC to the CM9700-CC1. For CM9700-MGR software installation instructions, refer to the CM9700-MGR Software Guide. • If your system is a networked system containing a CM9700-NW1 network interface unit, the CM9700-MGR PC connects to the CM9700-NW1 rather than to a CM9700-CC1. To connect the CM9700-MGR PC to the CM9700-CC1, refer to Figure 3 and do the following: 1. Using a null modem cable (not provided), connect one end of the cable to the COM 1 or COM 2 DB9 port on the CM9700-MGR PC. 2. Connect the other end of the cable to the COM1 DB9 port on the CM9700-CC1. NOTE: Either COM 1 or COM 2 on the CM9700-CC1 can be used for connection to the CM9700-MGR PC. COM 1 is conŢgured at the factory for use with the CM9700-MGR PC and RS-232 communication. Refer to Figure 4 for a diagram of null modem cable wiring connections. 16 C1572M (9/05) TO CM9700-CC1 TO CM9700-MGR PC COM 1/COM 2 PORT COM 1/COM 2 PORT PIN 3 (TX) PIN 2 (RX) PIN 2 (RX) PIN 3 (TX) PIN 5 (GND) PIN 5 (GND) NULL MODEM CABLE (RS-232) DB9 FEMALE DB9 FEMALE Figure 4. CM9700-MGR PC to CM9700-CC1 Null Modem Cable Connections Connecting a VGA Monitor to the CM9700-CC1 When connected to the CM9700-CC1, a VGA monitor displays the CM9700-CC1 diagnostic screen (refer to Monitoring CM9700-CC1 Functions in the System Diagnostics section for detailed information about the CM9700-CC1 diagnostic screen). Connect a VGA monitor to the VGA port of the CM9700-CC1 (refer to Figure 3). Connecting a PS/2 Keyboard to the CM9700-CC1 A PS/2 keyboard is supplied with the CM9700-CC1. To connect the keyboard to the CM9700-CC1, refer to Figure 3 and do the following: 1. Connect the supplied PS/2-to-AT keyboard adapter to the keyboard. 2. Connect the other end of the adapter to the AT-compatible keyboard port on the CM9700-CC1. NOTE: An AT-compatible keyboard port also exists on the front of the CM9700-CC1 behind the front door. Both keyboard ports cannot be used at the same time. Connecting Devices to CM9700-CC1 RS-422 Serial Communication Ports RS-422 serial communication ports 5-36, commonly referred to as SERCOM ports, are provided on the CM9700-CC1 for communication with devices such as matrix bays, keyboards, and pan/tilt or dome receivers. Before connecting devices to the SERCOM ports, note the following: • For a new system installation, refer to the System 9760 port assignment table titled “System 9760 Factory Default Port Settings” that is provided in the System 9760 binder. The port assignment table lists the CM9700-CC1 ports and the particular device that should be connected to each port as conŢgured at the factory for your system. For additional information about the port assignment table, refer to the Using the System 9760 Port Assignment Table section. • Certain devices must be connected to SERCOM ports in a particular order based on device priority. In a new system installation that has been conŢgured at the factory, connecting devices according to the port assignments provided in the System 9760 port assignment table ensures that you connect the correct device to the correct port. If you add devices to an existing system, it is recommended that you conŢgure your system using the CM9700-MGR software before connecting devices to SERCOM ports. The CM9700-MGR software automatically assigns devices to SERCOM ports in the correct order. By connecting devices according to the port assignments in CM9700-MGR, you ensure that you connect the correct device to the correct port. For detailed information about SERCOM port device priorities, refer to the SERCOM Port Device Priority Connections section. To connect a device to a SERCOM port, attach an RJ-45 data cable from the device to the appropriate SERCOM port. An RJ-45 data cable is included with each 9760 system device for connection to the CM9700-CC1. For detailed information about connecting a matrix bay to the CM9700-CC1, refer to the Installing CM9760-MXB Matrix Bay(s) section. For detailed information about connecting an ASCII communication device to the CM9700-CC1, refer to Appendix A. For detailed information about connecting other devices to the CM9700-CC1, refer to the manual supplied with the device. NOTE: Shielded cabling is required to comply with CE emissions guidelines. C1572M (9/05) 17 Using the System 9760 Port Assignment Table The System 9760 port assignment table, titled “System 9760 Factory Default Port Settings,” lists the CM9700-CC1 port numbers (1-36) and each device that has been assigned to a particular CM9700-CC1 port and conŢgured for your system at the factory. Figure 5 illustrates a sample port assignment table for a system containing a CM9700-MGR (System Manager) PC, three CM9760-MXBs, and one CM9760-KBD. Note that the port assignment table for your system will differ from the one shown in Figure 5 depending on the types and number of devices included in your system. System9760FactoryDefaultPortSettings 36 28 20 12 35 27 19 11 34 26 18 10 33 25 17 9 32 24 16 8 31 23 15 7 30 22 14 6 PRINTER COM1 COM2 29 21 13 5 Note: The number of ports on your system may differ from the above drawing. Connect System 9760 components as follows: PORT DESCRIPTION PORT DESCRIPTION 1(RS-232) SYSTEMMANAGER 19 2(RS-232) 20 3 NOTAVAILABLE 4 NOTAVAILABLE 5 CM9760-MXB (2A) (OUTPUTS 1-16) 23 CM9760-MXB (2B) (OUTPUTS 17-32) 6 24 7 CM9760-MXB (2C) (OUTPUTS 33-48) 25 8 CM9760-KBD (PIN 1111) 26 927 10 28 11 29 12 30 13 31 14 32 15 33 16 34 17 35 18 36 Figure 5. Sample Port Assignment Table 18 C1572M (9/05) In the sample port assignment table shown in Figure 5, note the following: • CM9700-CC1 port 1 (COM 1) is assigned and conŢgured for the System Manager; therefore, the System Manager PC should be connected to COM 1 on the CM9700-CC1. NOTE: For all systems conŢgured at the factory, COM 1 is always conŢgured as the port to be used with the System Manager PC. • CM9700-CC1 port 2 (COM 2) is not assigned or conŢgured for any device. • Because CM9700-CC1 ports 3 and 4 are not present on the CM9700-CC1, ports 3 and 4 are grayed out and are described as NOT AVAILABLE. • CM9700-CC1 port 5 is assigned and conŢgured for the CM9760-MXB labeled 2A containing video outputs 1-16; therefore, the CM9760-MXB labeled 2A should be connected to port 5 on the CM9700-CC1. • CM9700-CC1 port 6 is assigned and conŢgured for the CM9760-MXB labeled 2B containing video outputs 17-32; therefore, the CM9760-MXB labeled 2B should be connected to port 6 on the CM9700-CC1. • CM9700-CC1 port 7 is assigned and conŢgured for the CM9760-MXB labeled 2C containing video outputs 33-48; therefore, the CM9760-MXB labeled 2C should be connected to port 7 on the CM9700-CC1. • CM9700-CC1 port 8 is assigned and conŢgured for the CM9760-KBD having a pin number of 1111; therefore, the CM9760-KBD should be connected to port 8 on the CM9700-CC1. • Because no additional devices are included in the system, CM9700-CC1 ports 9-36 are not assigned or conŢgured for any device. SERCOM Port Device Priority Connections The CM9760-HS hot switch, CM9700-NW1 network interface unit (required in a networked system), and CM9760-MXB matrix bays must be connected to SERCOM ports in a particular order based on device priority. The CM9760-HS has the highest priority and, if present in the system, always connects to SERCOM port 5. The CM9700-NW1 has the next highest priority if present in the system, followed by CM9760-MXBs. If neither a CM9760-HS nor a CM9700-NW1 is present, then CM9760-MXBs have the highest priority and must be connected to the CM9700-CC1 starting at port 5. As a result, the order of connections depends on whether the system includes a CM9760-HS hot switch, a CM9700-NW1, or both. Note that CM9760-MXBs must be connected in sequential order. After all CM9760-MXBs have been connected, all other devices—such as keyboards—can then be connected in any order. Table A, Table B, Table C, and Table D provide a list of the appropriate order of device connections to SERCOM ports in various types of systems. The tables also include the device tree view portion of the CM9700-MGR Main window. The device tree identiŢes the appropriate port number assigned to each device in the system. Table A. RS-422 SERCOM Port Connections in a Single-Node System with a CM9760-HS Hot Switch Device SERCOM Port Connection CM9700-MGR Device Tree Port Assignments CM9760-HS Port 5 CM9760-MXB(s) Port 6 and next sequential ports as necessary— connected through the hot switch Other devices Any available ports connected through the hot switch—connections do not have to be in sequential ports C1572M (9/05) 19 Table B. RS-422 SERCOM Port Connections in a Single-Node System without a CM9760-HS Hot Switch Device SERCOM Port Connection CM9700-MGR Device Tree Port Assignments CM9760-MXB(s) Port 5 and next sequential ports as necessary Other devices Any available ports—connections do not have to be in sequential ports Table C. SERCOM Port Connections in a Networked System with a CM9760-HS Hot Switch Device SERCOM Port Connection CM9700-MGR Device Tree Port Assignments CM9760-HS Port 5 CM9700-NW1 Port 6—connected through the hot switch network interface unit Matrix bay(s) Port 7 and next sequential ports as necessary— connected through the hot switch Other devices Any available ports connected through the hot switch—connections do not have to be in sequential ports Table D. SERCOM Port Connections in a Networked System without a CM9760-HS Hot Switch Device SERCOM Port Connection CM9700-MGR Device Tree Port Assignments CM9700-NW1 network Port 5 on each CM9700-CC1 in the network interface unit Matrix bay(s) Port 6 and next sequential ports as necessary Other devices Any available ports—connections do not have to be in sequential ports NOTE: If you add matrix bays to an existing system, you may need to change existing port connections to be able to connect each additional matrix bay to the lowest sequential port possible. Connecting Power to the CM9700-CC1 To connect power to the CM9700-CC1, connect the supplied 120 VAC or 230 VAC power cord to the power input receptacle on the CM9700-CC1 and to an approved power source. NOTE: Do not power on the CM9700-CC1 until all system devices have been connected to the CM9700-CC1 and all system devices have been powered on. 20 C1572M (9/05) POWERING ON THE CM9700-CC1 After all system devices have been connected to the CM9700-CC1 and all system devices have been powered on, power on the CM9700-CC1. To power on the unit, place the power switch in the On (I) position. If, for some reason, you must power off the unit, place the power switch in the Off (0) position. INSTALLING CM9760-MXB MATRIX BAY(S) Your System 9760 installation may include one or multiple CM9760-MXB matrix bays. Installation of a CM9760-MXB includes the following tasks: • Selecting a location for the CM9760-MXB in an EIA standard rack • Mounting the CM9760-MXB • Verifying CM9760-MXB component installation • Connecting the CM9760-MXB to the CM9700-CC1 • Connecting power to the CM9760-MXB • Powering on the CM9760-MXB • Checking diagnostic LEDs • Connecting video inputs and outputs To perform each of the above tasks, refer to the sections that follow. SELECTING A LOCATION FOR THE CM9760-MXB The CM9760-MXB is designed to be mounted into a standard 19-inch (48.26 cm) EIA rack. When selecting a location in a rack for a CM9760-MXB, note the following: • The CM9760-MXB occupies 6 RUs or 10.5 inches (26.7 cm) of vertical rack space. • Allow at least 1 RU or 1.75 inches (4.5 cm) of space above the CM9760-MXB for air circulation. In a high-temperature environment, it may also be necessary to provide forced air cooling. Contact Product Support for additional information. • The maximum distance allowable between a CM9760-MXB and the CM9700-CC1 is 4,000 feet (1,219 meters). Note that a 10-foot (3.05 meters) reversed cable is supplied with the CM9760-MXB for connection to the CM9700-CC1. If you install a CM9760-MXB farther than 10 feet from the CM9700-CC1, you must create your own cable. In addition, if you are installing multiple matrix bays, note the following: • When expanding video inputs beyond 256 as provided by a single matrix bay, the expansion of video inputs occurs in a horizontal manner using a sideframing conŢguration. As a result, each additional matrix bay should be installed at the same level in a nearby rack. When installing a new system containing multiple matrix bays to be sideframed, note that the rear of each matrix bay is labeled to identify the location of each matrix bay in the sideframe conŢguration. For example, the matrix bays are labeled 2A, 12A, 22A, and so on. • When expanding video outputs beyond 16 as provided by a single matrix bay, the expansion of video outputs occurs in a vertical manner using a downframing conŢguration. As a result, multiple matrix bays must be installed in the same rack. When installing a new system containing multiple matrix bays to be downframed, note that the rear of each matrix bay is labeled to identify the location of each matrix bay in the downframe conŢguration. For example, the matrix bays are labeled 2A, 2B, 2C, and so on. • When expanding video inputs beyond 256 and video outputs beyond 16, a combination of sideframing and downframing is used. When installing a new system containing multiple matrix bays to be sideframed and downframed, note that the rear of each matrix bay is labeled to identify the location of each matrix bay in the sideframe and downframe conŢguration. For example, matrix bays to be side- framed are labeled 2A, 12A, 22A, and so on; and matrix bays to be downframed are labeled 2B, 12B, 22B, and so on. To help you determine the location of multiple matrix bays in your system, refer to Appendix B for sample illustrations of matrix bay conŢgurations. Note the labeling of the matrix bays shown in the sample illustrations. In addition, for detailed information about sideframing and downframing, refer to Sideframing and Downframing in the CM9760-MXB Matrix Bay section. C1572M (9/05) 21 MOUNTING THE CM9760-MXB DANGER: Always install equipment starting from the bottom of the rack. Installing equipment starting from the top of the rack can cause the rack to topple. To mount a CM9760-MXB into a rack, install the CM9760-MXB into the desired location and secure the unit using the supplied mounting hardware (refer to Figure 6). Figure 6. Mounting the CM9760-MXB If you are mounting multiple matrix bays, note the following: • If you are installing a new system, be sure to mount the matrix bays in a horizontal (sideframe) or vertical (downframe) manner according to the bay location label provided on the rear of each matrix bay (refer to the Selecting a Location for the CM9760-MXB section for additional information.) • After mounting matrix bays in a downframe conŢguration, connect each supplied coaxial ribbon cable, referred to as a downframe cable, to downframe connectors on rear panel cards as appropriate. The downframe cables are required to connect the video inputs from one matrix bay to another. Figure 7 illustrates sample downframe cable connections between a CM9760-RPC card and a CM9760-DFC card and between a CM9760-RPC card and a CM9760-DFL card in a conŢguration containing one downframed bay. For additional information, refer to Downframing in the CM9760-MXB Matrix Bay section and to Appendix B. 22 C1572M (9/05) CM9760-MXB Alarm Black BAY 1 Out RS-422 RS-422 CAMS 1-256 RPC RPC SUPPLIED DOWN- OR FRAMING CABLES 16X RIBBON COAXIAL CM9760-MXB Alarm Black BAY 2 Out RS-422 RS-422 DFC DFL Figure 7. Sample Downframe Cable Connections VERIFYING CM9760-MXB COMPONENT INSTALLATION Up to 16 CM9760-VCC video input cards, one CM9760-VMC video output card, and up to two power supplies are installed in a matrix bay at the factory as ordered. Verify component installation as follows: 1. Remove the front panel of the matrix bay to view the video input and output cards. 2. Verify that the correct number of cards and power supplies are installed. In addition, verify that each installed card and power supply is properly seated in the matrix bay. Refer to the following sections for detailed information. C1572M (9/05) 23 Removing the CM9760-MXB Front Panel To remove the front panel of the CM9760-MXB, loosen the eight captive panel screws indicated in Figure 8. CAPTIVE PANEL SCREW (4) FRONT PANEL CAPTIVE PANEL SCREW (4) Figure 8. CM9760-MXB Front Panel WARNING: Although the CM9760-MXB will function properly with the front panel removed, the front panel must be attached during system operation to meet safety standards. To reattach the front panel, tighten the eight captive panel screws. Verifying Input Card, Output Card, and Power Supply Installation The CM9760-MXB accepts up to 16 CM9760-VCC video input cards in slots 1-16, one CM9760-VMC card in slot 17, and up to two power supplies (refer to Figure 9). With the front panel removed, verify that the correct number of cards are installed as ordered and that they are Ţrmly seated in the appropriate slots. In addition, verify that the correct number of power supplies are installed as ordered and that each installed power supply is Ţrmly seated in the power supply slot. +10V -10V FRAME SUPPLY FAULT FAULT +10V -10V FRAME SUPPLY FAULT FAULT CM9760-VCC CM9760-VMC VIDEO OUTPUT VIDEO INPUT CARDS CARD (SLOT 17) (SLOTS 1-16) Figure 9. Sample CM9760-MXB ConŢguration NOTE: The conŢguration of your CM9760-MXB may differ from the conŢguration shown in Figure 9 depending on the number of video input cards and power supplies ordered. If your conŢguration contains only one power supply, a blank plate covers the lower power supply slot. 24 C1572M (9/05) CONNECTING THE CM9760-MXB TO THE CM9700-CC1 Connect a CM9760-MXB to the CM9700-CC1 using the 10-foot (3.05 meters) reversed cable supplied with the CM9760-MXB. If you must create a longer cable, it is recommended that you use a 24-gauge twisted pair cable. As illustrated in Figure 10, connect the female RJ-45 serial communications data port labeled RS-422 on the rear of the CM9760-MXB to the appropriate female RJ-45 serial communications port (RS-422) on the rear of the CM9700-CC1. Figure 10 provides an example of a CM9760-MXB connected to port 5 on the CM9700-CC1. 8-PIN SERCOM PORT (FEMALE) PIN 1=Tx+ PIN 1 PIN 2=Tx– . . . CM9760-MXB (FULLY LOADED) PIN 7=Rx– PIN 8 PIN 8=Rx+ CM9700-CC1 REVERSED DATA CABLE (SUPPLIED) RS-422 DATA CABLE CONNECTIONS CM9760-MXB CM9700-CC1 RJ-45 RJ-45 CONNECTOR CONNECTOR PIN 1=Tx+ PIN 1=Tx+ PIN 2=Tx– PIN 2=Tx– . . . . . . . . PIN 7=Rx– PIN 7=Rx– PIN 8=Rx+ PIN 8=Rx+ Figure 10. CM9760-MXB to CM9700-CC1 Connection C1572M (9/05) 25 CONNECTING POWER TO THE CM9760-MXB NOTE: A CM9760-MXB operates on 120 VAC, 60 Hz. A CM9760-MXB-X operates on 230 VAC, 50 Hz. To connect power to a CM9760-MXB, plug the supplied power cord into the power input receptacle on the rear of the matrix bay for each power supply installed (refer to Figure 11). Then plug the power cord for each installed power supply into an approved power source. Alarm Black Out RS-422 RS-422 POWER CORD CONNECTION TO UPPER POWER SUPPLY POWER SWITCH FOR UPPER POWER SUPPLY POWER SWITCH FOR LOWER POWER SUPPLY POWER CORD CONNECTION TO LOWER POWER SUPPLY Figure 11. CM9760-MXB Power Connections (Two Power Supplies Installed) POWERING ON THE CM9760-MXB NOTE: Do not power on the CM9760-MXB until after it is connected to the CM9700-CC1. To power on a CM9760-MXB, place the corresponding power switch of each installed power supply in the On (I) position. If, for some reason, you must power off the CM9760-MXB, place the corresponding power switch of each installed power supply in the Off (0) position. CHECKING DIAGNOSTIC LEDS Checking the diagnostic LEDs on a CM9760-MXB allows you to ensure that the unit is operating properly. It is recommended that you check the LEDs on the CM9760-MXB before connecting video inputs and outputs to the unit. With the CM9760-MXB powered on, check the LEDs as follows: 1. For each power supply installed, do the following: a. Verify that the +10V and –10V power LEDs are lit (green). If a power LED is not lit, ensure that the power supply is seated properly. If the condition persists, inspect the power supply fuse and replace the fuse if necessary (refer to Replacing a Power Supply Fuse in the CM9760-MXB Component Installation or Replacement section for detailed instructions). b. Verify that the Frame Fault and the Supply Fault LEDs are not lit. If the Frame Fault LED is lit (red), one or more video input/output cards has failed. Continue with step 2 for troubleshooting information. If the Supply Fault LED is lit (red), replace the power supply (refer to Replacing a Power Supply in the CM9760-MXB Component Installation or Replacement section for detailed instructions). 26 C1572M (9/05) 2. With the front panel of the CM9760-MXB removed, check the LEDs on the CM9760-VCC video input cards and on the CM9760-VMC video output card as follows (refer to Figure 12): a. Verify that all +10 VDC and –10 VDC power LEDs are lit (green). If a power LED is not lit, remove the card and inspect the fuses (refer Figure 13 for fuse locations on CM9760-VCC and CM9760-VMC cards). Replace fuse(s) if necessary. If the condition continues, replace the card. For instructions to replace a CM9760-VCC or CM9760-VMC card, refer to Replacing a CM9760-VCC Card or to Replacing a CM9760-VMC Card in the CM9760-MXB Component Installation or Replacement section as applicable. b. Verify that all Comm Fail LEDs are not lit: • If the LED is lit (red) on any video input card, reseat the card. If the condition continues, replace the card. • If the Comm Fail LED is lit (red) on the video output card only, check the communication to the CM9700-CC1. • If all Comm Fail LEDs are lit (red), press the Reset button located on the video output card (refer to Figure 12). If the problem continues, replace the video output card. For a summary of troubleshooting information relating to the CM9760-MXB, refer to Troubleshooting the CM9760-MXB in the Troubleshooting section. After you have veriŢed that the CM9760-MXB is operating properly, reattach the front panel of the CM9760-MXB. Then connect video inputs and outputs (refer to the Connecting Video Inputs and Video Outputs section). COMM FAIL COMM FAIL +10 VDC -10 VDC +10 VDC NO ASSIGNMENT -10 VDC RESET BUTTON CM9760-VCC CM9760-VMC VIDEO INPUT CARD VIDEO OUTPUT CARD Figure 12. CM9760-VCC and CM9760-VMC Diagnostic LEDs C1572M (9/05) 27 .7ASB FUSES CM9760-VCC VIDEO INPUT CARD .7ASB FUSES CM9760-VMC VIDEO OUTPUT CARD Figure 13. Fuse Locations on CM9760-VCC and CM9760-VMC Cards 28 C1572M (9/05) CONNECTING VIDEO INPUTS AND VIDEO OUTPUTS Connect all video inputs (up to 256) and all video outputs (up to 16) to the rear panel BNC cards (refer to Figure 14). 1 241 1 Alarm Black Out RS-422 RS-422 16 256 16 Figure 14. CM9760-MXB Video Input and Output Connections Note the following: • To provide adequate ground and signal connections, use crimp-on BNCs rather than screw-on BNCs. • Allow enough slack in a cable to act as a strain relief between the cable and the BNC connectors. • Be sure each connection is secure. • Label all cabling to minimize system downtime if troubleshooting becomes necessary and cabling needs to be disconnected. • Video output from the CM9760-VMC video output card is not terminated. Terminate the video signal at the output device (for example, monitor,VCR, or matrix switcher). If you are looping to other devices, terminate the last device only. • The endpoint of any video cable run must be teminated in 75 ohms. • For information about sideframing video inputs and downframing video outputs, refer to Sideframing and Downframing in the CM9760-MXB Matrix Bay section. C1572M (9/05) 29 VERIFYING SYSTEM OPERATION After installation of the 9760 system is complete, verify system operation. To do so, perform the following from a CM9760-KBD: 1. Verify that the CM9760-KBD LCD displays the following: SYSTEM 97XX NOTE: Depending on the version of the CM9760-KBD software, the LCD displays SYSTEM 9760 or SYSTEM 9700. 2. Enter the default operator password on the CM9760-KBD keypad: The default password for operator 1 is 0101; the default password for operator 2 is 0202; the default password for operator 3 is 0303, and so on. The passwords are deŢned in the Operator PIN Ţeld in CM9700-MGR. The LCD displays the following: ENTER MONITOR # 3. Enter the number of the monitor you are viewing—for example, 1—and then press the MON key. 4. Enter a camera number, and then press the CAM key. 5. Press the FWD key to advance through cameras and verify switching. For detailed information about 9760 system operation using the CM9760-KBD, refer to the CM9760-KBD/KBR Keyboard Installation/Operation manual. 30 C1572M (9/05) CM9700-CC1 Component Installation or Replacement WARNINGS: • Installation or replacement of CM9700-CC1 components should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing or replacing CM9700-CC1 components. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. This section provides information about the following: • Removing the top cover of the CM9700-CC1 (the top cover must be removed before CM9700-CC1 components can be installed or replaced) • Installing or replacing a CM9700-SER card For information about replacing the VGA card (CM9700-CC1-VID) in the CM9700-CC1, refer to the CM9700-CC1-VID VGA Video Card Installation manual. For information about adding CM9700-SER-32 port expander units to the CM9700-CC1, refer to the CM9700-SER-32 Port Expander Installation/Operation manual. REMOVING THE CM9700-CC1 TOP COVER To remove the top cover of the CM9700-CC1, refer to Figure 15 and do the following: 1. Power off the CM9700-CC1. WARNING: Failure to power off the CM9700-CC1 can result in serious damage to the equipment. 2. Remove the ten screws that hold the top cover in place. 3. Tilt the top cover up at a slight angle as indicated by the dotted line in Figure 15, and then pull the cover backwards to remove the cover from the front edge of the CM9700-CC1 chassis. Figure 15. CM9700-CC1 Top Cover Removal C1572M (9/05) 31 INSTALLING OR REPLACING A CM9700-SER CARD WARNINGS: • CM9700-SER card installation or replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing or replacing a CM9700-SER card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. The CM9700-CC1 is shipped from the factory with a minimum of two CM9700-SER cards installed on the motherboard in ISA slots 1 and 2 (refer to Figure 16). You can install additional CM9700-SER cards into ISA slots 3 and 4, totaling a maximum of four cards. You can also replace an existing card. When installing or replacing a CM9700-SER card, you must set the interrupt and address jumpers on the new card. CM9700-SER CARD ACCESS SLOTS (SLOT COVERS REMOVED) CC1 CHASSIS, REAR ISA SLOTS (DEFAULT CM9700-SER CARDS SUPPLIED IN ISA SLOTS 1 AND 2) CC1 CHASSIS, FRONT Figure 16. CM9700-CC1 with Top Cover Removed To install or replace a CM9700-SER card, do the following: 1. Power off the CM9700-CC1. WARNING: Failure to power off the CM9700-CC1 can result in serious damage to the equipment. 2. Remove the top cover of the CM9700-CC1 (refer to the Removing the CM9700-CC1 Top Cover section). 3. If replacing an existing CM9700-SER card, remove the card from the ISA slot. 4. On the new CM9700-SER card, set the W1 interrupt (IRQ) and W2 address select jumpers (refer to Figure 17 and to Table E). Note that the jumper settings vary depending on the ISA slot into which the card is to be installed. If you are replacing a card, the jumper settings should match the settings on the card being replaced. 32 C1572M (9/05) W1 IRQ SELECT PIN 2 PIN 22 PIN 1 PIN 21 W2 ADDRESS SELECT PIN 2 PIN 4 PIN 1 PIN 3 Figure 17. Sample CM9700-SER Card Jumper Assignments Table E. CM9700-SER Card Jumper Assignments ISA Slot Number W1 IRQ Setting W2 Address Setting 1 IRQ 10 Pins 1 to 2 and 3 to 4 2 IRQ 11 Pins 1 to 2 only 3 IRQ 12 Pins 3 to 4 only 4* IRQ 5 No jumpers *The jumper assignments shown for ISA slot 4 are applicable to the CM9700-CC1 but are not applicable to the CM9700-NW1. A maximum of three CM9700-SER cards can be installed into the CM9700-NW1 (ISA slots 1, 2, and 3). The CM9700-NW1 is shipped from the factory with a minimum of one CM9700-SER card installed into ISA slot 1. 5. Install the new CM9700-SER card into the desired slot. 6. Reattach the front cover of the CM9700-CC1. 7. Power on the CM9700-CC1. Note the following: • You can cycle through the IRQ/address settings by toggling the ALT+A key combination on the PC keyboard associated with the CM9700-CC1 diagnostic screen. (For information about the CM9700-CC1 diagnostic screen, refer to the System Diagnostics section.) • When connecting system devices to the serial communication ports of the CM9700-SER card, shielded cabling is required to comply with CE emissions guidelines. C1572M (9/05) 33 IRQ 3 IRQ 4 IRQ 5 IRQ 6 IRQ 7 IRQ 9 IRQ 10 IRQ 11 IRQ 12 IRQ 14 IRQ 15 CM9760-MXB Component Installation or Replacement WARNINGS: • Installation or replacement of CM9760-MXB components should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing or replacing CM9760-MXB components. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. This section provides information about the following: • Installing or replacing rear panel cards (CM9760-RPC, CM9760-RPL, CM9760-DFC, CM9760-DFL, and CM9760-RPM) • Installing or replacing a CM9760-VCC video input card • Installing or replacing a CM9760-VMC video output card • Installing a CM9760-VMM module on a CM9760-VMC video output card • Installing or replacing a power supply • Replacing a power supply fuse In addition, this section also provides information about enabling/disabling the power supply alarm. INSTALLING OR REPLACING REAR PANEL CARDS CM9760-RPC, CM9760-RPL, CM9760-DFC, CM9760-DFL, and CM9760-RPM cards are installed into the rear of the matrix bay. For an initial system installation, the cards are installed at the factory as ordered. Rear panel cards (and associated front panel cards) can be added to expand a system or can be replaced if necessary. NOTE: Rear panel cards must be installed before the associated CM9760-VCC video input card or CM9760-VMC video output card is installed into the front of the matrix bay. INSTALLING OR REPLACING A CM9760-RPC REAR PANEL INPUT CARD Up to 16 CM9760-RPC cards can be installed into 16 possible slot positions that are associated with the slot positions of the corresponding CM9760-VCC cards to be installed. If necessary, a CM9760-RPC card can be replaced. To install or replace a CM9760-RPC card, refer to the sections that follow. Installing a CM9760-RPC Card WARNINGS: • Rear panel card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: A CM9760-RPC card must be installed before the associated CM9760-VCC video input card is installed. To install a CM9760-RPC card, do the following: 1. Set termination jumpers JP1-JP16 (refer to Figure 18) in the proper position: • In a single-bay configuration, the setting of the jumpers depends on whether video is to be looped to another device (for example, a DVR, VCR, or matrix switcher): – When looping is not required, set the jumpers in the terminated position (jumper positions 1 and 2) (default setting). – When looping is required, set the jumpers in the unterminated position (jumper positions 2 and 3). • In multiple-bay configurations, set the jumpers in the unterminated position. 2. Locate the desired slot position at the rear of the bay. NOTE: The physical number of a video input is determined by the position of the CM9760-VCC card, which is installed into the front of the matrix bay. Viewed from the rear of the matrix bay, slot 1 is located on the right and corresponds to physical input numbers 1-16, slot 2 corresponds to physical input numbers 17-32, and so on. As a result, if you do not install CM9760-RPC cards in sequential order, be sure to use the correct physical input number when programming the system using the CM9700-MGR. 3. Remove the blank cover plate by loosening the screw at the top and bottom of the plate. 34 C1572M (9/05) 4. Slide the new card into the card guides (refer to Figure 19). 5. Push the card into place Ţrmly. 6. Tighten the screw at the top and bottom of the card. 7. Connect BNC and downframe cables as applicable. UNTERMINATED TERMINATED JP1-JP16 Figure 18. Termination Jumpers on CM9760-RPC Rear Panel Input Card Figure 19. CM9760-RPC Rear Panel Input Card Installation C1572M (9/05) 35 Replacing a CM9760-RPC Card WARNINGS: • Rear panel card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: Before replacing a CM9760-RPC card, you must remove the front panel of the matrix bay and disconnect the associated CM9760-VCC video input card from the connectors on the backplane and from the connector on the CM9760-RPC card that is to be replaced. To disconnect the CM9760-VCC card, grasp the two card handles and Ţrmly pull the card toward you until the card is disconnected (refer to the Installing or Replacing a CM9760-VCC Video Input Card section for additional information). To replace a CM9760-RPC card, do the following: 1. Ensure that the associated CM9760-VCC video input card is disconnected as noted above. 2. Disconnect BNC and downframe cables, as applicable, from the CM9760-RPC card being replaced. 3. Remove the CM9760-RPC card by loosening the screw at the top and bottom of the card and then pulling the card toward you until it is out of the frame. 4. Install the new CM9760-RPC card (refer to the Installing a CM9760-RPC Card section). Note that you should set the termination jumpers on the new card to match the jumper positions on the card being replaced. After the CM9760-RPC card has been replaced, reconnect the associated CM9760-VCC card by sliding the card toward the rear of the matrix bay until the card is seated Ţrmly with the backplane connectors and the CM9760-RPC connector. Note that, unless the audible alarm on the power supply has been disabled, the alarm beeps twice and the Frame Fault LED ţashes red twice. Then reattach the front panel of the matrix bay. 36 C1572M (9/05) INSTALLING OR REPLACING A CM9760-RPL REAR PANEL LOOPING CARD The CM9760-RPL rear panel looping card contains two rows of BNC connectors and therefore occupies two slot positions in the matrix bay. The CM9760-RPL card connects to one CM9760-VCC video input card, which is installed into the front of the matrix bay. Up to eight CM9760-RPL cards can be installed when a maximum of 128 video inputs is required in a system that also requires looping. If necessary, a CM9760-RPL card can be replaced. To install or replace a CM9760-RPL card, refer to the sections that follow. Installing a CM9760-RPL Card WARNINGS: • Rear panel card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a rear panel card. Always wear a grounding strap con- nected to an approved grounding source when working on or near exposed electronic equipment. NOTE: A CM9760-RPL card must be installed before the associated CM9760-VCC video input card is installed. To install a CM9760-RPL card, do the following: 1. Set termination jumpers JP1-JP16 (refer to Figure 20) in the proper position: • When looping functions are required, set the jumpers in the unterminated position (positions 2 and 3). • When looping functions are not required, set the jumpers in the terminated position (positions 1 and 2). TERMINATED UNTERMINATED JP1-JP16 Figure 20. Termination Jumpers on CM9760-RPL Card 2. Locate the desired slot position at the rear of the bay. NOTE: In a bay that is to be fully populated with CM9760-RPL cards, each card must be installed into an odd slot position only. The corresponding CM9760-VCC cards must also occupy odd slot positions. C1572M (9/05) 37 3 2 1 3. Remove the blank cover plate by loosening the screw at the top and bottom of the plate. 4. Slide the new card into the card guides (refer to Figure 21). Figure 21. CM9760-RPL Rear Panel Looping Card Installation 5. Push the card into place Ţrmly. 6. Tighten the two screws at the top and bottom of the card. 7. Connect BNC and downframe cables as applicable. Replacing a CM9760-RPL Card WARNINGS: • Rear panel card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: Before replacing a CM9760-RPL card, you must remove the front panel of the matrix bay and disconnect the associated CM9760-VCC video input card from the connectors on the backplane and from the connector on the CM9760-RPL card that is to be replaced. To disconnect the CM9760-VCC card, grasp the two card handles and Ţrmly pull the card toward you until the card is disconnected (refer to the Installing or Replacing a CM9760-VCC Video Input Card section for additional information). To replace a CM9760-RPL card, do the following: 1. Ensure that the associated CM9760-VCC video input card is disconnected as noted above. 2. Disconnect BNC and downframe cables, as applicable, from the CM9760-RPL card being replaced. 3. Remove the CM9760-RPL card by loosening the two screws at the top and bottom of the card and then pulling the card toward you until it is out of the frame. 4. Install the new card (refer to the Installing a CM9760-RPL Card section). Note that you should set termination jumpers on the new card to match the jumper positions on the card being replaced. After the CM9760-RPL card has been replaced, reconnect the associated CM9760-VCC card by sliding the card toward the rear of the matrix bay until the card is seated Ţrmly with the backplane connectors and CM9760-RPL connector. Note that, unless the audible alarm on the power supply has been disabled, the alarm beeps twice and the Frame Fault LED ţashes red twice. Then reattach the front panel of the matrix bay. 38 C1572M (9/05) INSTALLING OR REPLACING A CM9760-DFC DOWNFRAME CARD The CM9760-DFC card is installed in every bay between the Ţrst and last bays in a downframe conŢguration. The card can also be used in the last bay if looping is not required. Up to 16 CM9760-DFC cards can be installed into 16 possible slot positions that are associated with the slot positions of the corresponding CM9760-VCC cards to be installed. If necessary, a CM9760-DFC card can be replaced. To install or replace a CM9760-DFC card, refer to the sections that follow. Installing a CM9760-DFC Card WARNINGS: • Rear panel card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: A CM9760-DFC card must be installed before the associated CM9760-VCC video input card is installed. To install a CM9760-DFC card, do the following: 1. Set termination jumpers JP1-JP16 (refer to Figure 22) in the proper position: • When CM9760-DFC cards are to be installed in intermediate bays, set the jumpers in the unterminated position (jumper positions 2 and 3). • When CM9760-DFC cards are to be installed in the last bay, set the jumpers in the terminated position (jumper positions 1 and 2). UNTERMINATED 3 2 1 TERMINATED Figure 22. Termination Jumpers on CM9760-DFC Downframe Card 2. Locate the desired slot position at the rear of the bay. 3. Remove the blank cover plate by loosening the screw at the top and bottom of the plate. 4. Slide the new card into the card guides (refer to Figure 23). C1572M (9/05) 39 JP 16 JP 1 Figure 23. CM9760-DFC Downframe Card Installation 5. Push the card into place Ţrmly. 6. Tighten the screw at the top and bottom of the card. 7. Connect downframe cables as applicable. Replacing a CM9760-DFC Card WARNINGS: • Rear panel card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: Before replacing a CM9760-DFC card, you must remove the front panel of the matrix bay and disconnect the associated CM9760-VCC video input card from the connectors on the backplane and from the connector on the CM9760-DFC card that is to be replaced. To disconnect the CM9760-VCC card, grasp the two card handles and Ţrmly pull the card toward you until the card is disconnected (refer to the Installing or Replacing a CM9760-VCC Video Input Card section for additional information). To replace a CM9760-DFC card, do the following: 1. Ensure that the associated CM9760-VCC video input card is disconnected as noted above. 2. Disconnect downframe cables, as applicable, from the CM9760-DFC card being replaced. 3. Remove the CM9760-DFC card by loosening the screw at the top and bottom of the card and then pulling the card toward you until it is out of the frame. 4. Install the new card (refer to the Installing a CM9760-DFC Card section). Note that when setting the termination jumpers on the new card, the jumper positions should match the jumper positions on the card being replaced. After the CM9760-DFC has been replaced, reconnect the associated CM9760-VCC card by sliding the card toward the rear of the matrix bay until the card is seated Ţrmly with the backplane connectors and CM9760-DFC connector. Note that, unless the audible alarm on the power supply has been disabled, the alarm beeps twice and the Frame Fault LED ţashes red twice. Then reattach the front panel of the matrix bay. 40 C1572M (9/05) INSTALLING OR REPLACING A CM9760-DFL DOWNFRAME LOOPING CARD The CM9760-DFL downframe looping card is used in the last bay in a downframe conŢguration. Note the following: • In a CM9760-MXB(-X), the CM9760-DFL card connects to a CM9760-VCC video input card, which is installed into the front of the matrix bay. Up to 16 CM9760-DFL cards can be installed into 16 possible slot positions that are associated with the slot positions of the corresponding CM9760-VCC cards to be installed. • In a CM9760-MXBL, up to 16 CM9760-DFL cards can be installed into slot positions that correspond to the video input slot positions in the bay above. In the CM9760-MXBL, the CM9760-DFL cards do not connect to CM9760-VCC cards. If necessary, a CM9760-DFL card can be replaced. To install or replace a CM9760-DFL card, refer to the sections that follow. Installing a CM9760-DFL Card WARNINGS: • Rear panel card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: When a CM9760-DFL card is to be connected to a CM9760-VCC video input card, the CM9760-DFL card must be installed before the associated CM9760-VCC card is installed. To install a CM9760-DFL card, do the following: 1. Set termination jumpers JP1-JP16 (refer to Figure 24) in the proper position: • When looping to another device is required, set the jumpers in the unterminated position (jumper positions 2 and 3). Termination must occur at the final device. • When looping is not required, set the jumpers in the terminated position (jumper positions 1 and 2). UNTERMINATED TERMINATED JP1-JP16 Figure 24. Termination Jumpers on CM9760-DFL Card 2. Locate the desired slot position at the rear of the bay. 3. Remove the blank cover plate by loosening the screw at the top and bottom of the plate. C1572M (9/05) 41 4. Slide the new card into the card guides (refer to Figure 25). Figure 25. CM9760-DFL Downframe Looping Card Installation 5. Push the card into place Ţrmly. 6. Tighten the screw at the top and bottom of the card. 7. Connect BNC and downframe cables as applicable. Replacing a CM9760-DFL Card WARNINGS: • Rear panel card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: Before replacing a CM9760-DFL card in a CM9760-MXB(-X), you must remove the front panel of the matrix bay and disconnect the associated CM9760-VCC video input card from the connectors on the backplane and from the connector on the CM9760-DFL card that is to be replaced. To disconnect the CM9760-VCC card, grasp the two card handles and Ţrmly pull the card toward you until the card is disconnected (refer to the Installing or Replacing a CM9760-VCC Video Input Card section for additional information). To replace a CM9760-DFL card, do the following: 1. CM9760-MXB(-X) only: Ensure that the associated CM9760-VCC video input card is disconnected as noted above. 2. Disconnect BNC and downframe cables, as applicable, from the CM9760-DFL card being replaced. 3. Remove the CM9760-DFL card by loosening the screw at the top and bottom of the card and then pulling the card toward you until it is out of the frame. 4. Install the new card (refer to the Installing a CM9760-DFL Card section). Note that when setting the termination jumpers on the new card, you should match the jumper positions on the card being replaced. CM9760-MXB(-X) only: After the CM9760-DFL has been replaced, reconnect the associated CM9760-VCC card by sliding the card toward the rear of the matrix bay until the card is seated Ţrmly with the backplane connectors and CM9760-DFL connector. Note that, unless the audible alarm on the power supply has been disabled, the alarm beeps twice and the Frame Fault LED ţashes red twice. Then reattach the front panel of the matrix bay. 42 C1572M (9/05) INSTALLING OR REPLACING A CM9760-RPM REAR PANEL OUTPUT CARD Only one CM9760-RPM card can be installed into the rear of the matrix bay. The card must always be installed into the leftmost slot. From the rear of the bay, the leftmost slot provides the connection point for the CM9760-VMC video output card, which is always installed into slot 17 in the front of the bay. If necessary, a CM9760-RPM card can be replaced. To install or replace a CM9760-RPM card, refer to the sections that follow. Installing a CM9760-RPM Card WARNINGS: • Rear panel card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: A CM9760-RPM card must be installed before the associated CM9760-VMC video input card is installed. To install a CM9760-RPM card, do the following: 1. Ensure that termination jumpers JP1-JP16 are set in the unterminated position (positions 2 and 3) (refer to Figure 26). UNTERMINATED TERMINATED JP1-JP16 Figure 26. Termination Jumpers on CM9760-RPM Card 2. Locate the desired slot position at the rear of the bay. 3. Remove the blank cover plate by loosening the screw at the top and bottom of the plate. 4. Slide the new card into the card guides of the leftmost slot (refer to Figure 27). C1572M (9/05) 43 Figure 27. CM9760-RPM Rear Panel Output Card Installation 5. Push the card into place Ţrmly. 6. Tighten the screw at the top and bottom of the card. 7. Connect BNC cables (or ribbon cable, if applicable). Replacing a CM9760-RPM Card WARNINGS: • Rear panel card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a rear panel card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. NOTE: Before replacing a CM9760-RPM card, you must remove the front panel of the matrix bay and disconnect the associated CM9760-VMC video output card from the connectors on the backplane and from the connector on the CM9760-RPM card that is to be replaced. To disconnect the CM9760-VMC card, grasp the two card handles and Ţrmly pull the card toward you until the card is disconnected. Unless the audible alarm on the power supply has been disabled, the alarm beeps and the Frame Fault LED ţashes red when the CM9760-VMC card is disconnected (refer to the Installing or Replacing a CM9760-VMC Video Output Card section for additional information). To replace a CM9760-RPM card, do the following: 1. Ensure that the associated CM9760-VMC video output card is disconnected as noted above. 2. Disconnect BNC cables (or ribbon cable, if applicable) from the CM9760-RPM card being replaced. 3. Remove the CM9760-RPM card by loosening the screw at the top and bottom of the card and then pulling the card toward you until it is out of the frame. 4. Install the new card (refer to the Installing a CM9760-RPM Card section). After the CM9760-RPM card has been replaced, reconnect the associated CM9760-VMC card by sliding the card toward the rear of the matrix bay until the card is seated Ţrmly with the backplane connectors and CM9760-RPM connector. If the audible alarm on the power supply is enabled, the alarm stops beeping and the Frame Fault LED turns off. To ensure proper operation of the CM9760-VMC card, reset the card by pressing the Reset button on the card. For about Ţve seconds, the audible alarm on the power supply beeps and the Frame Fault LED ţashes red. Then reattach the front panel of the matrix bay. 44 C1572M (9/05) INSTALLING OR REPLACING A CM9760-VCC VIDEO INPUT CARD CM9760-VCC video input cards are installed into the front of the matrix bay behind the front panel. For an initial system installation, the cards are installed at the factory as ordered. CM9760-VCC cards (and associated rear panel cards) can be added to expand a system or can be replaced if necessary. To install or replace a CM9760-VCC card, refer to the sections that follow. INSTALLING A CM9760-VCC CARD WARNINGS: • CM9760-VCC video input card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a CM9760-VCC card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. Before installing a CM9760-VCC card, note the following: • A CM9760-VCC card can be installed while the matrix bay is powered on. • A CM9760-VCC card can be installed into any available slot ranging from slot 1 to slot 16, totaling a maximum of 16 CM9760-VCC cards. A CM9760-VCC card cannot be installed into slot 17—slot 17 is reserved for the CM9760-VMC video output card. • Each slot position (slots 1-16) into which a CM9760-VCC card can be installed corresponds to a speciŢc range of physical inputs; for example, slot position 1 corresponds to physical inputs 1-16, slot position 2 corresponds to physical inputs 17-32, and so on. Physical input numbers are used when programming the CM9760-MXB using the CM9700-MGR; therefore, if you do not install CM9760-VCC cards in sequential order, be sure to use the correct physical input numbers when programming the CM9760-MXB. Table F lists the 16 slot positions and their corresponding physical input range. Table F. CM9760-VCC Slot Positions and Corresponding Physical Input Range Slot Physical Slot Physical Position Input Range Position Input Range 1 1-16 9 129-144 2 17-32 10 145-160 3 33-48 11 161-176 4 49-64 12 177-192 5 65-80 13 193-208 6 81-96 14 209-224 7 97-112 15 225-240 8 113-128 16 241-256 • The CM9760-VCC card requires a rear panel input card: CM9760-RPC, CM9760-RPL, CM9760-DFC, or CM9760-DFL. The associated rear panel input card should be installed into the correct slot in the rear of the matrix bay before a CM9760-VCC card is installed. For instructions to install rear panels cards, refer to the Installing or Replacing Rear Panel Cards section. C1572M (9/05) 45 To install a CM9760-VCC card, do the following: 1. Remove the front panel of the matrix bay. 2. Insert the CM9760-VCC card into the desired slot (slots 1-16) as follows (refer to Figure 28): a. Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay. b. Slide the card toward the rear of the matrix bay until the card is seated Ţrmly with the connectors on the backplane and with the associated rear panel card connector. Note that, unless the audible alarm on the power supply has been disabled, the alarm beeps twice and the Frame Fault LED ţashes red twice. The LEDs on the CM9760-VCC card indicate proper operation. 3. Reattach the front panel of the matrix bay. SLOT 17 (RESERVED FOR VIDEO OUTPUT CARD) VIDEO INPUT CARDS (SLOTS 1-16) CARD HANDLE FRAME FAULT LED CARD HANDLE CARD GUIDE Figure 28. CM9760-VCC Video Input Card Installation (Slots 1-16) 46 C1572M (9/05) REPLACING A CM9760-VCC CARD WARNINGS: • CM9760-VCC video input card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a CM9760-VCC card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. To replace a CM9760-VCC card, do the following: 1. Remove the front panel of the matrix bay. 2. Remove the CM9760-VCC card to be replaced by grasping the two card handles and Ţrmly pulling the card out of the connectors on the backplane and associated rear panel card. The card slides out of the slot. 3. Install the new card into the slot of the card being replaced (refer to the Installing a CM9760-VCC Card section for installation instructions). C1572M (9/05) 47 INSTALLING OR REPLACING A CM9760-VMC VIDEO OUTPUT CARD One CM9760-VMC4, CM9760-VMC8, CM9760-VMC12, or CM9760-VMC16 video output card can be installed in the CM9760-MXB. For an initial system installation, the CM9760-VMC card is installed at the factory as ordered. If additional matrix bays are ordered to expand an existing system, the CM9760-VMC card may need to be installed. If necessary, a CM9760-VMC card can be replaced. To install or replace a CM9760-VMC card, refer to the sections that follow. INSTALLING A CM9760-VMC CARD WARNINGS: • CM9760-VMC video output card installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when installing a CM9760-VMC card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. Before installing a CM9760-VMC card, note the following: • The CM9760-VMC card can be installed while the matrix bay is powered on. • The CM9760-VMC card must always be installed into slot 17 in the front of the matrix bay. • The CM9760-VMC card requires the CM9760-RPM rear panel video output card. The CM9760-RPM card should be installed in the correct slot in the rear of the matrix bay before the CM9760-VMC card is installed. For instructions to install a CM9760-RPM card, refer to the Installing a CM9760-RPM Card section. • When installed in the matrix bay at the factory according to your system order, the S2 DIP switch and X55 and JP2 jumper settings on the CM9760-VMC card are set in the proper position. You must, however, set DIP switch and jumper settings on a new card as instructed in the procedure below. 48 C1572M (9/05) ON 1 2 3 4 To install a CM9760-VMC card, do the following: 1. Remove the front panel of the matrix bay. 2. Remove the blank cover plate of slot 17 by loosening the screw at the top and bottom of the plate. 3. Set the S2 DIP switch and the X55 and JP2 jumpers on the new card to be installed: a. Refer to Figure 29 for DIP switch and jumper locations on the CM9760-VMC card. b. Refer to Table G for S2 DIP switch functions and associated settings. c. Refer to Table H for X55 video standards and associated jumper positions. d. Ensure that the JP2 jumper is installed in the two-pin header. The JP2 jumper must always be installed for proper operation. S2 JP2 X55 Figure 29. DIP Switch and Jumper Locations on CM9760-VMC Video Output Card C1572M (9/05) 49 Table G. S2 DIP Switch Functions and Settings Function Options Switch Setting 1 Off 2400 2 Off 1 Off 4800 2On Baud Rate 1On 9600 2 Off 1On 19200 2On NTSC* 3 Off Video Standard PAL* 3 On Enabled 4 On Video Loss Detection Disabled (default) 4 Off *X55 jumper must also be set (refer to Table H). Table H. X55 Video Standards and Associated Jumper Positions Jumper Positions Video Oscillator Standard Frequency Pins 1 to 2 Pins 3 to 4 Pins 5 to 6 Pins 7 to 8 SECAM1 5.0 MHz On On On On SECAM2 5.0 MHz On On Off On 624 5.0 MHz On Off On On PAL/CCIR 5.0 MHz On Off Off On NTSC1 5.034964 MHz On On On Off NTSC2 5.034964 MHz On On Off Off 524 5.034964 MHz On Off On Off PAL-M 5.034964 MHz On Off Off Off 50 C1572M (9/05) 4. Install the new card into slot 17 of the matrix bay as follows (refer to Figure 30): a. Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay. b. Slide the card toward the rear of the matrix bay until the card is seated Ţrmly with the connectors on the backplane and with the associated rear panel card connector. If the audible alarm on the power supply is enabled, the alarm stops beeping and the Frame Fault LED turns off. c. To ensure proper operation of the CM9760-VMC card, reset the card by pressing the Reset button on the card. For about Ţve seconds, the audible alarm on the power supply beeps and the Frame Fault LED ţashes red. The LEDs on the video output card then indicate proper operation. 5. Reattach the front panel of the matrix bay. CARD VIDEO OUTPUT CARD GUIDE (SLOT 17) CARD HANDLE FRAME FAULT LED LEDs RESET BUTTON CARD HANDLE CARD GUIDE Figure 30. CM9760-VMC Video Output Card Installation (Slot 17) C1572M (9/05) 51 OUTPUT 15 OUTPUT 14 OUTPUT 13 OUTPUT 12 OUTPUT 11 OUTPUT 10 OUTPUT 9 OUTPUT 8 OUTPUT 7 OUTPUT 6 OUTPUT 5 OUTPUT 4 OUTPUT 3 OUTPUT 2 OUTPUT 1 OUTPUT 0 REPLACING A CM9760-VMC CARD WARNINGS: • CM9760-VMC video output card replacement should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed when replacing a CM9760-VMC card. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. Before replacing a CM9760-VMC card, note the following: • The CM9760-RPM card can be replaced while the matrix bay is powered on. • When installed in the matrix bay at the factory according to your system order, the S2 DIP switch and X55 and JP2 jumper settings on the CM9760-RPM card are set in the proper position. You must, however, set DIP switch and jumper settings on a new card as instructed in the procedure below. To replace the CM9760-VMC card, do the following: 1. Remove the front panel of the matrix bay. 2. Remove the CM9760-VMC card to be replaced by grasping the two card handles and Ţrmly pulling the card out of the connectors on the backplane and associated rear panel card. The card slides out of the slot. NOTE: Unless the audible alarm on the power supply has been disabled, the alarm beeps and the Frame Fault LED ţashes red when the CM9760-VMC card is removed. 3. Install the new CM9760-VMC card (refer to the Installing a CM9760-VMC Card section). Note that you should set the S2 DIP switch and the X55 and JP2 jumpers on the new card to match the settings on the card being replaced. INSTALLING A CM9760-VMM VIDEO OUTPUT MODULE WARNINGS: • CM9760-VMM video output module installation should be performed by qualiŢed personnel only. • Electrostatic discharge (ESD) precautions must be observed. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic equipment. • When installing a CM9760-VMM module, exercise caution to prevent bending any of the pins on the module. To install a CM9760-VMM module into an empty slot on a CM9760-VMC4, CM9760-VMC8, or CM9760-VMC12 card, align the pins on the module with the three sockets on the card (refer to Figure 31) and push the card down carefully until the pins are Ţrmly seated into the sockets. VIDEO EMPTY OUTPUT SLOTS MODULES Figure 31. CM9760-VMM Video Output Module Locations (CM9760-VMC8 Video Output Card) NOTE: CM9760-VMM slot locations on the CM9760-VMC card are numbered OUTPUT 0 to OUTPUT 15—not OUTPUT 1 to OUTPUT 16. 52 C1572M (9/05) INSTALLING OR REPLACING A POWER SUPPLY Unless a backup power supply is ordered with the matrix bay, the unit is shipped from the factory with one power supply installed. A backup power supply can be added to the matrix bay to provide power redundancy to the unit. If necessary, a power supply can be replaced. Note the following: • The CM9760-MXB uses the CM9760-MPS power supply (120 VAC, 60 Hz). • The CM9760-MXB-X uses the CM9760-MPS-X power supply (230 VAC, 50 Hz). • A power supply provides an audible alarm that operates in conjunction with the Fault LEDs located on the front of the power supply. By default, the alarm is enabled. You can disable the alarm if desired. For additional information, refer to the Enabling/Disabling the Power Supply Alarm section. INSTALLING A BACKUP POWER SUPPLY NOTE: You can install a backup power supply while the matrix bay is powered on. You do not need to turn off power to the unit. To install a backup power supply, do the following: 1. Remove the blank plate from the unoccupied power supply slot. 2. Align the power supply in the mounting rails and then slide the power supply into the slot (refer to Figure 32). 3. Press Ţrmly on the front of the power supply until it is Ţrmly seated into the rear connector. 4. Tighten the two captive panel screws at the top and bottom of the power supply. 5. Plug the power cord into the power input receptacle of the power supply. 6. Plug the other end of the power cord into the power source. 7. Place the power switch of the power supply in the On (I) position. Figure 32. CM9760-MXB Backup Power Supply Installation C1572M (9/05) 53 REPLACING A POWER SUPPLY To replace a power supply, do the following: 1. Remove the power supply to be replaced as follows: a. Place the power switch in the Off (0) position. b. Disconnect the power cord from the power source. c. Remove the power supply from the power supply slot as follows: (1) Loosen the two captive panel screws at the top and bottom of the power supply. (2) Pull the power supply toward you. The power supply slides out of the slot. 2. Install the new power supply as follows: a. Align the power supply in the mounting rails and then slide the power supply into the slot. b. Press Ţrmly on the front of the power supply until it is Ţrmly seated into the rear connector. c. Tighten the two captive panel screws at the top and bottom of the power supply. d. Plug the power cord into the power source. e. Place the power switch of the power supply in the On (I) position. 54 C1572M (9/05) REPLACING A POWER SUPPLY FUSE The rear of the matrix bay provides a separate power input receptacle for each power supply. Each power input receptacle is equipped with a fuse holder (refer to Figure 33). Each fuse holder provides a spare fuse to be used when replacing a blown fuse. WARNING: Failure to replace a fuse with a fuse of the same rating can result in serious damage to the matrix bay. To replace the fuse in a power supply, do the following: 1. Remove the power cord from the power input receptacle. 2. Using a small screwdriver, pry the fuse holder out of the socket. The fuse holder comes out of the unit. 3. Replace the fuse with a fuse of the same rating. If using the spare fuse, be sure to replace it with a fuse of the same rating. 4. Install the fuse holder back into the socket. 5. Plug the power cord into the power input receptacle. STORAGE DRAWER FOR SPARE FUSE FUSE HOLDER Figure 33. CM9760-MXB Power Supply Fuse Replacement C1572M (9/05) 55 ENABLING/DISABLING THE POWER SUPPLY ALARM The power supply provides an audible alarm that operates in conjunction with the Fault LEDs located on the front of the power supply. By default, the alarm is enabled. The X5 jumper on the power supply allows you to enable/disable the alarm (refer to Figure 34). To enable/disable the audible power supply alarm, do the following: 1. Place the power switch of the power supply in the Off (0) position. 2. Disconnect the power cord from the power source. 3. Remove the power supply from the power supply slot as follows: a. Loosen the two captive panel screws at the top and bottom of the power supply. b. Pull the power supply toward you. The power supply slides out of the slot. 4. Locate the X5 jumper on the power supply (refer to Figure 34). 5. Position the jumper to enable/disable the alarm as shown in Figure 34. X5 ALARM ALARM DISABLED ENABLED Figure 34. CM9760-MXB Power Supply Alarm Jumper Positions 6. Install the power supply back into the power supply slot as follows: a. Align the power supply in the mounting rails and then slide the power supply into the slot. b. Press Ţrmly on the front of the power supply until it is Ţrmly seated into the rear connector. c. Tighten the two captive panel screws at the top and bottom of the power supply. 7. Plug the power cord into the power source. 8. Place the power switch of the power supply in the On (I) position. 56 C1572M (9/05) System Programming Using DOS ® ® The CM9700-CC1 runs under Microsoft DOS (Disk Operating System) 6.22, referred to as MS-DOS 6.22 and also commonly referred to simply as DOS. This section provides information about the following: • System 9760 programming tasks that are performed using DOS operations • DOS Ţlename conventions • DOS commands that are commonly used when managing 9760 system Ţles NOTES: • For an overview of the DOS directory structure of the CM9700-CC1, refer to Directory Structure in the CM9700-CC1 Controller section. • For detailed information about programming the 9760 system using the CM9700-MGR, refer to the CM9700-MGR Software Guide. PERFORMING SYSTEM 9760 DOS PROGRAMMING TASKS Using DOS operations, you can perform the following tasks: • Copy conŢguration Ţles from the CM9700-MGR to the CM9700-CC1 • Set and adjust system time in a single-node system • Set and adjust system time in a multi-node system To perform each of the above tasks, refer to the sections that follow. COPYING CONFIGURATION FILES FROM THE CM9700-MGR TO THE CM9700-CC1 NOTE: Before copying conŢguration Ţles from the CM9700-MGR to the CM9700-CC1, it is recommended that you save a copy of the existing CM9700-CC1 conŢguration Ţles. To copy conŢguration Ţles from the CM9700-MGR to the CM9700-CC1, do the following: 1. Export conŢguration Ţles from the CM9700-MGR to a ţoppy disk using the Export to ConŢguration Files option of the CM9700-MGR. For detailed instructions, refer to the CM9700-MGR Software Guide. 2. Insert the ţoppy disk into the disk drive of the CM9700-CC1. 3. Using the keyboard connected to the AT-compatible keyboard port of the CM9700-CC1, press Ctrl+Q to exit the 9760 system. The VGA monitor displays the C:\9700> prompt. 4. At the prompt, copy all conŢguration Ţles from the ţoppy disk to the CM9700-CC1 by entering the following: copy a:Ţlename.* where Ţlename is the root name of the conŢguration Ţles. For example, if the root name is NODE1, enter the following: copy a:node1.* 5. Press Enter. Either of the following occurs: • The configuration files are copied to the CM9700-CC1. Skip step 6 and proceed to step 7. • If the previous configuration files exist in the C:\9700 directory, the following message appears: Files Already Exist, Over Write? Y/N/A Continue with step 6. 6. Enter A to overwrite all existing Ţles on the CM9700-CC1 with the Ţles contained on the ţoppy disk. NOTE: Entering Y for Yes requires that you conŢrm on a Ţle-by-Ţle basis that you wish to overwrite the existing Ţle. Entering N for No requires that you conŢrm on a Ţle-by-Ţle basis that you do not wish to overwrite the existing Ţle. 7. Remove the ţoppy disk from the disk drive of the CM9700-CC1. 8. Press Ctrl+Alt+Delete to reboot the CM9700-CC1. Note that you must press the Del key on the numeric keypad of your keyboard in order to reboot the system. C1572M (9/05) 57 SETTING AND ADJUSTING SYSTEM TIME IN A SINGLE-NODE SYSTEM You can set system time in a single-node system using the PC keyboard that is connected to the AT-compatible keyboard port of the CM9700-CC1. Using the CM9700-CC1 PC keyboard, you can also adjust system time if the system clock is running fast (system lead time) or slow (system lag time). For detailed instructions to set and adjust system time, refer to the sections that follow. NOTE: System time can also be set using the CM9760-KBD rather than the CM9700-CC1 PC keyboard; however, to adjust system time, the CM9700-CC1 PC keyboard must be used. Setting System Time in a Single-Node System Before setting system time, note the following: • Begin the process of setting system time close to the top of the hour. • When setting system time, you must synchronize the system clock to a reference time clock (RTC). • In a conŢguration having a CM9760-HS hot switch, setting and adjusting time on one CM9700-CC1 synchronizes the time between both CM9700-CC1s. (For detailed information about the CM9760-HS hot switch, refer to the CM9760-HS Hot Switch Installation/Operation manual.) To set the system time using the CM9700-CC1 PC keyboard, do the following: 1. From the CM9700-CC1 diagnostic screen, press Alt+N to display the current conŢguration Ţlename. The conŢguration Ţlename is displayed in the System box. You will need to enter the name later in this procedure when directed. 2. Press Ctrl+Q to exit the 9760 system. The C:\9700> prompt appears. 3. At the prompt, enter time and then press Enter. The currently set time is displayed and the following prompt appears: Enter new time: 4. Do the following: a. Enter a time equaling the top of the hour in the xx:xx:xx.xx format followed by the letter a for AM or p for PM (for example, 2:00:00.00p for 2:00 PM). Do not press Enter. b. Wait for the RTC to approach the top of the hour. c. When the RTC equals the top of the hour, press Enter. 5. At the C:\9700> prompt, invoke the system executable by entering startup and then pressing Enter. After the CM9700-CC1 initializes, the CM9700-CC1 diagnostic screen appears. In addition, the system time entered in step 4 is displayed on all monitors in the system. After the system has run 24 hours or a multiple of 24 hours, you can adjust system time if the system clock is running fast or slow when compared to the RTC. To adjust system time, refer to the Adjusting System Time in a Single-Node System section. 58 C1572M (9/05) Adjusting System Time in a Single-Node System To adjust system time in a single-node system, do the following: 1. Wait 24 hours—or a multiple of 24 hours if necessary—since the system time was set, and then compare the system time displayed on any monitor in the system with the RTC time. Note the difference in time for a 24-hour period and whether the system time is ahead of or behind RTC time. For example, if system time is 2:02:30 PM and RTC time is 2 PM after a 24-hour period, then system time is ahead of RTC time by 2 minutes and 30 seconds. If the amount of time over which you are comparing system time to RTC time is a multiple of 24 hours, perform steps a-c that follow to determine the difference in time per 24-hour period; otherwise, proceed to step 2. a. Convert the time difference noted between system time and RTC time to seconds. b. Divide the total number of seconds by the elapsed time in hours to determine the seconds per hour rate of change. For example, if a 90-second time difference had occurred over a time interval of 3 days or 72 hours, then the rate of change in seconds per hour is 1.25 (90 divided by 72 = 1.25). c. Multiply the seconds per hour rate of change by 24 to obtain the time difference in seconds for a 24-hour period. For example, multiplying 1.25 by 24 equals a time difference of 30 seconds per 24-hour period. 2. Using the CM9760-KBD, set system time at the top of the hour in 24-hour format. For example, if RTC time equals 2:00 PM, enter the following: 14 00 00 3. At the CM9700-CC1 diagnostic screen, press Alt+L using the CM9700-CC1 PC keyboard. The System box displays the following: System :-Last Adj 0:0.0 Total 0:0.0 4. Enter the time difference noted in step 1 in the following format: –mm.ss.hh or mm:ss.hh where: • – = minus sign. A minus sign must be entered if system time is ahead of RTC time and must be slowed for synchronization with RTC time. • mm = minutes • ss = seconds • hh = hundredths of a second For example, to enter the time difference of 2 minutes and 30 seconds noted in step 1 in order to slow system time over the next 24 hours, enter the following: –02:30.00 5. Press Enter. 6. Press Alt+L to display the adjustment you have made to system time. The adjustment is displayed in the System box on the diagnostic screen. For example, for the time difference of 2 minutes and 30 seconds that was entered in step 4 above, the System box displays the following: Last Adj. –2:30.0 Total –2.30.0 where: Last Adj. displays the last time adjustment that was made in minutes, seconds, and hundredths of a second. In the example, the last adjustment that was made is –2:30.0. Total displays the total time adjustment that was made in minutes, seconds, and hundredths of a second. In the example, the total adjustment that was made is –2:30.0. After the system has run 24 hours or a multiple of 24 hours after the time adjustment was made, you can adjust the system time again if necessary. To make additional adjustments to system time, refer to the Making Additional Adjustments to System Time section. C1572M (9/05) 59 NOTE: The time adjustment that was made to system time as displayed in step 6 above is a temporary time adjustment. If you reboot the CM9700-CC1 by pressing Ctrl+Alt+Del or exit the 9760 system by pressing Ctrl+Q, the time adjustment reverts to 0:0.0. As a result, you must edit the startup.bat Ţle to permanently program the total time adjustment indicated in the System box after the Ţnal time adjustment is made. Instructions for editing the startup.bat Ţle are provided in the Editing the Startup.bat File to Permanently Adjust System Time section. Making Additional Adjustments to System Time To make an additional adjustment to system time, do the following: 1. Wait 24 hours—or a multiple of 24 hours if necessary—since the last time adjustment was made, and then compare the system time displayed on any monitor in the system with the RTC time. Note the difference in time for a 24-hour period and whether the system time is ahead of or behind RTC time. 2. Using the CM9760-KBD, set system time at the top of the hour in 24-hour format when the RTC reaches the top of the hour. 3. At the CM9700-CC1 diagnostic screen, press Alt+L. The System box displays the latest time adjustment values. For example, if a time adjustment of –2:30.00 was entered to slow system time 2 minutes and 30 seconds, the System box displays the following: Last Adj. –2:30.0 Total –2.30.0 4. Enter a new time adjustment based on adding or subtracting time from the last time adjustment that was made. For example, when comparing system time with RTC time after Ţve 24-hour periods have passed since the last time adjustment was made and determining that system time is running 10 seconds slow—an average of 2 seconds slower for each 24 hours of elapsed time—you can change the last time adjustment by adding 2 seconds. If the last time adjustment was –02:30.00, the following time adjustment must be entered as follows to add 2 seconds: –02:28.0 Note that –02.28.0 is derived from the following equation: [(–02:30.0) + (00:02.0)] = –02.28.0 5. Press Enter. The System box displays the last time adjustment and total time adjustment values. In the example, the System box displays the following: Last Adj. –2:28.0 Total –4.58.0 Note that the total time adjustment is –4.58.0. 6. If necessary, continue to make additional time adjustments until the system clock and RTC are synchronized. NOTE: The time adjustments that are made to system time are temporary time adjustments. If you reboot the CM9700-CC1 by pressing Ctrl+Alt+Del or exit the 9760 system by pressing Ctrl+Q, the time adjustment values revert to 0:0.0. As a result, you must edit the startup.bat Ţle to permanently program the total time adjustment indicated in the System box after the Ţnal time adjustment is made. Instructions for editing the startup.bat Ţle are provided in the Editing the Startup.bat File to Permanently Adjust System Time section. 60 C1572M (9/05) Editing the Startup.bat File to Permanently Adjust System Time To permanently adjust system time, you must edit the startup.bat Ţle to include the total time adjustment indicated in the System box after the Ţnal adjustment is made to system time. To edit the startup.bat Ţle to include the total time adjustment, do the following: 1. Press Ctrl+Q to exit the 9760 system. The C:\9700> prompt appears. 2. At the prompt, enter edit startup.bat and then press Enter. The startup.bat Ţle opens and appears as follows: CM9700 NODEx where: x is the node number: • NODE1 is the default configuration filename for a single-node system. • Default configuration filenames for each node within a multi-node system are numbered sequentially according to the CM9700-NW1 port number to which each CM9700-CC1 is connected, for example, NODE5 and NODE6 in a two-node system. 3. Edit the startup.bat Ţle to include the total time adjustment as follows: CM9700 NODEx /T:–mm:ss:hh or CM9700 NODEx /T:mm:ss:hh where: • /T = time adjustment switch command • – = minus sign. A minus sign must be entered if system time is ahead of RTC time and must be slowed for synchronization with RTC time. • mm = minutes • ss = seconds • hh = hundredths of a second For example, to enter the total time adjustment of 4 minutes and 58 seconds to slow the system clock in a 24-hour period, edit the startup.bat Ţle as follows: CM9700 NODEx /T:-04:58:00 4. Press Alt+F and then type the letter s to save the Ţle. 5. Press Alt+F and then type the letter x to exit the Ţle. 6. At the C:\9700 prompt, enter startup and then press Enter to restart the system. The time adjustment is now permanent. If you reboot the CM9700-CC1 by pressing Ctrl+Alt+Del or exit the 9760 system by pressing Ctrl+Q, the time adjustment remains in system memory and does not revert to 0:0.0. C1572M (9/05) 61 SETTING AND ADJUSTING SYSTEM TIME IN A MULTI-NODE SYSTEM You can set system time in a multi-node system using the PC keyboard that is connected to the AT-compatible keyboard port of the CM9700-NW1. The CM9700-NW1 then provides system timing to the network. Using the CM9700-NW1 PC keyboard, you can also adjust system time if the system clock is running fast (system lead time) or slow (system lag time). For detailed instructions to set and adjust system time, refer to the sections that follow. NOTE: System time can also be set using the CM9760-KBD rather than the CM9700-NW1 PC keyboard; however, to adjust system time, the CM9700-NW1 PC keyboard must be used. Setting System Time in a Multi-Node System Before setting system time, note the following: • Begin the process of setting system time close to the top of the hour. • When setting system time, you must synchronize the system clock to a reference time clock (RTC). • If the CM9700-NW1 goes ofţine, each node reverts to its own internal system time. To set system time using the CM9700-NW1 PC keyboard, do the following: 1. Press Ctrl+Q to exit the CM9700-NW1 diagnostic screen. The screen provides a display similar to the following: Program end. Vectors reset. 11:36:49.12 Mon 06-22-2005 C:\NETWORK>_ 2. At the prompt, enter time and then press Enter. The currently set time is displayed and the following prompt appears: Enter new time: 3. Do the following: a. Enter a time equaling the top of the hour in the xx:xx:xx.xx format followed by the letter a for AM or p for PM (for example, 2:00:00.00p for 2:00 PM). Do not press Enter. b. Wait for the RTC to approach the top of the hour. c. When the RTC equals the top of the hour, press Enter. 4. At the C:\NETWORK> prompt, invoke the system executable by entering net and then press Enter. The system time entered in step 3 is displayed on all monitors in the system. After the system has run 24 hours or a multiple of 24 hours, you can adjust system time if the system clock is running fast or slow when compared to the RTC. To adjust system time, refer to the Adjusting System Time in a Multi-Node System section. 62 C1572M (9/05) Adjusting System Time in a Multi-Node System To adjust system time in a multi-node system, do the following: 1. Wait 24 hours—or a multiple of 24 hours if necessary—since the system time was set, and then compare the system time displayed on any monitor in the system with the RTC time. Note the difference in time for a 24-hour period and whether the system time is ahead of or behind RTC time. For example, if system time is 2:02.30 PM and RTC time is 2 PM after a 24-hour period, then system time is ahead of RTC time by 2 minutes and 30 seconds. If the amount of time over which you are comparing system time to RTC time is a multiple of 24 hours, perform steps a-c that follow to determine the difference in time per 24-hour period; otherwise, proceed to step 2. a. Convert the time difference noted between system time and RTC time to seconds. b. Divide the total number of seconds by the elapsed time in hours to determine the seconds per hour rate of change. For example, if a 90-second time difference had occurred over a time interval of 3 days or 72 hours, then the rate of change in seconds per hour is 1.25 (90 divided by 72 = 1.25). c. Multiply the seconds per hour rate of change by 24 to obtain the time difference in seconds for a 24-hour period. For example, multiplying 1.25 by 24 equals a time difference of 30 seconds per 24-hour period. 2. Using the CM9760-KBD, set system time at the top of the hour in 24-hour format. For example, if RTC time equals 2:00 PM, enter the following: 14 00 00 3. At the CM9700-NW1 diagnostic screen, press Alt+L using the CM9700-NW1 PC keyboard. The screen provides a display similar to the following: **********TIME ADJUSTMENT********* Last Time Adjustment 0:0.0 Total Time Adjustment 0:0.0 Format Example +10:20.5 Adds 10 min 20.5 seconds per day -5:10.61 Subtracts 5 min 10.61 seconds per day ***********ESC TO CANCEL********** => 4. At the => system prompt, enter the time difference noted in step 1 in the following format: –mm.ss.hh or mm:ss.hh where: • – = minus sign. A minus sign must be entered if system time is ahead of RTC time and must be slowed for synchronization with RTC time. • mm = minutes • ss = seconds • hh = hundredths of a second For example, to enter the time difference of 2 minutes and 30 seconds noted in step 1 in order to slow system time over the next 24 hours, enter the following: –02:30.00 C1572M (9/05) 63 5. Press Enter. The adjustment is displayed. For example, for the adjustment of –02.30.00 that was made in step 4, the following line appears: Last Adj. –2:30.0 Total –2.30.0 where: Last Adj. displays the last time adjustment that was made in minutes, seconds, and hundredths of a second. In the example, the last adjustment that was made is –2:30:0. Total displays the total time adjustment that was made in minutes, seconds, and hundredths of a second. In the example, the total adjustment that was made is –2:30.0. 6. If desired, press Alt+N to check the system time. The line containing the system time appears similar to the following: Fri June 24 15:40:23 2005 CM9700 NIU Ver xxx xxx Setup Ţle:2nodes.niu After the system has run 24 hours or a multiple of 24 hours since a time adjustment was made, you can adjust the system time again if necessary. To make additional adjustments to system time, refer to the Making Additional Adjustments to System Time section. NOTE: The time adjustment that was made to system time as displayed in step 5 above is a temporary time adjustment. If you reboot the CM9700-NW1 by pressing Ctrl+Alt+Del or stop operation of the CM9700-NW1 by pressing Ctrl+Q, the time adjustment reverts to 0:0.0. As a result, you must edit the net.bat Ţle to permanently program the total time adjustment indicated on the diagnostic screen after the Ţnal time adjustment is made. Instructions for editing the net.bat Ţle are provided in the Editing the Net.bat File to Permanently Adjust System Time section. 64 C1572M (9/05) Making Additional Adjustments to System Time To make an additional adjustment to system time, do the following: 1. Wait 24 hours—or a multiple of 24 hours if necessary—since the last time adjustment was made, and then compare the system time displayed on any monitor in the system with the RTC time. Note the difference in time for a 24-hour period and whether the system time is ahead of or behind RTC time. 2. Using the CM9760-KBD, set system time at the top of the hour in 24-hour format when the RTC reaches the top of the hour. 3. At the CM9700-NW1 diagnostic screen, press Alt+L. The screen displays the latest time adjustment that was made. For example, if a time adjustment of –2:30.0 was entered to slow system time 2 minutes and 30 seconds, the screen displays the following: **********TIME ADJUSTMENT********* Last Time Adjustment –2:30.0 Total Time Adjustment –2:30.0 Format Example +10:20.5 Adds 10 min 20.5 seconds per day -5:10.61 Subtracts 5 min 10.61 seconds per day ***********ESC TO CANCEL********** => 4. At the => system prompt, enter a new time adjustment based on adding or subtracting time from the original time adjustment. For example, when comparing system time with RTC time after Ţve 24-hour periods have passed since the original time adjustment was made and determining that system time is running 10 seconds slow—an average of 2 seconds slower for each 24 hours of elapsed time—you can change the original time adjustment by adding 2 seconds. If the original time adjustment was –02:30.00, the following time adjustment must be entered as follows to add 2 seconds: –02:28.0 Note that –02.28.0 is derived from the following equation: [(–02:30.0) + (00:02.0)] = –02.28.0 5. Press Enter. The adjustment is displayed. For example, for the adjustment of –02.28.0 that was made in step 4, the following line appears: Last Adj. –2:28.0 Total –4.58.0 Note that the total time adjustment is –4.58.0. 6. If desired, press Alt+N to check the system time. The line containing the system time appears similar to the following: Sat June 25 15:40:18 2005 CM9700 NIU Ver xxx xxx Setup Ţle:2nodes.niu 7. If necessary, continue to make additional time adjustments until the system clock and RTC are synchronized. NOTE: The time adjustments that are made to system time are temporary time adjustments. If you reboot the CM9700-NW1 by pressing Ctrl+Alt+Del or stop operation of the CM9700-NW1 by pressing Ctrl+Q, the time adjustment values revert to 0:0.0. As a result, you must edit the net.bat Ţle to permanently program the total time adjustment indicated on the diagnostic screen after the Ţnal time adjustment is made. Instructions for editing the net.bat Ţle are provided in the Editing the Net.bat File to Permanently Adjust System Time section. C1572M (9/05) 65 Editing the Net.bat File to Permanently Adjust System Time To permanently adjust system time, you must edit the net.bat Ţle to include the total time adjustment indicated on the diagnostic screen after the Ţnal adjustment is made to system time. To edit the net.bat Ţle to include the total time adjustment, do the following: 1. Press Ctrl+Q to stop operation of the CM9700-NW1. The screen displays the following: Program end. Vectors reset. 11:36:49.12 Mon 06-27-2005 C:\NETWORK>_ 2. At the prompt, enter edit net.bat and then press Enter. The net.bat Ţle opens and appears as follows: 9700NIU xNODES where x equals the number of nodes in the network when the CM9700-NW1 is shipped as part of a system order, for example, 2NODES.NIU for a two-node system, 3NODES.NIU for a three-node system, and so on. The default conŢguration Ţle name is 2NODES.NIU when the CM9700-NW1 is shipped as a standalone unit. 3. Edit the net.bat Ţle to include the total time adjustment as follows: 9700NIU xNODES /T:-mm:ss:hh or 9700NIU xNODES /T:mm:ss:hh where: • /T = time adjustment switch command • – = minus sign. A minus sign must be entered if system time is ahead of RTC time and must be slowed for synchronization with RTC time. • mm = minutes • ss = seconds • hh = hundredths of a second For example, to enter the total time adjustment of 4 minutes and 58 seconds to slow the system clock in a 24-hour period, edit the net.bat Ţle as follows: 9700NIU xNODES /T:-04:58:00 4. Press Alt+F and then type the letter s to save the Ţle. 5. Press Alt+F and then type the letter x to exit the Ţle. 6. At the C:\NETWORK prompt, enter net and then press Enter to restart the system. The time adjustment is now permanent. If you reboot the CM9700-NW1 by pressing Ctrl+Alt+Del or stop operation of the CM9700-NW1, the time adjustment remains in memory and does not revert to 0:0.0. 66 C1572M (9/05) DOS FILENAME CONVENTIONS The naming convention for a DOS Ţlename is a root name followed by a period followed by an extension: • The root name is limited to eight characters with no spaces. • The extension is three characters. For example, if the Ţlename is NODE1.CAM, the root name is NODE1 and the extension is CAM. The following characters cannot be used in the root name or extension. The characters are reserved for particular uses as follows: \ (backslash) Used for directory navigation / (forward slash) Used as a delimiter in command line options : (colon) Used for a command prompt . (dot) Used as a separator between root and extension * (asterisk) Used as a wildcard character ? (question mark) Used as a wildcard character > (greater than symbol) Used as a command prompt < (less than symbol) Used as a command prompt DOS COMMAND REFERENCE Table I provides a listing of DOS commands that are commonly used when managing 9760 system Ţles. Table I. DOS Command Reference † †† § Command Switch Description Example(s) ¶ Directory Management Commands CD Displays the current C:\>CD Displays the root directory as directory. the current directory: C:\> Changes the current C:\>CD 9700 Changes from the root direc- directory. tory (C:\) to the 9700 directory: C:\9700> C:\>CD 9700\BKUP Changes from the root direc- tory to the BKUP directory within the 9700 directory: C:\9700\BKUP> C:\9700>CD.. Moves up one level in the directory structure. In the example, moves from the 9700 directory to the root directory. C:\9700\BKUP>CD\ Changes to the root directory. In the example, changes from the C:\9700\BKUP directory to the root directory. C:\>CD A: Changes from the root directory to the A drive. DIR Displays a list of Ţles C:\>DIR Displays a list of Ţles and and subdirectories subdirectories within the root within the speciŢed directory (C:\). directory. /W Displays the contents of C:\>DIR/W Displays the contents of the a directory in wide root directory in wide format. format. Up to Ţve Ţle- names or directory names are displayed on one line. C1572M (9/05) 67 Table I. DOS Command Reference (Continued) † †† § Command Switch Description Example(s) ¶ Directory Management Commands (Continued) DIR (Continued) /P Displays the contents of C:\>DIR/P Displays the contents of the a directory one screen at root directory one screen at a a time. time. /W/P Combines /W and /P C:\>DIR/W/P Displays the contents of the switches to display the root directory in wide format contents of a directory one screen at a time. in wide format one screen at a time. MD Creates a directory C:\9700>MD FACTORY Creates a directory named FACTORY within the 9700 directory. RD Removes the speciŢed C:\>RD NETWORK Removes the NETWORK or directory. The directory or directory if empty. RMDIR to be removed must not C:\>RMDIR NETWORK contain any Ţles or sub- directories—the direc- tory must be empty except for the single-dot (.) and double-dot (..) entries. TREE Displays the directory C:\TREE Displays the directories in the structure of the root directory and any speciŢed directory and associated subdirectories. those below it. File and Disk Management Commands COPY Copies a single Ţle or a C:\>COPY A:\NODE1.MON C:\9700 Copies the NODE1.MON Ţle group of Ţles from one from the ţoppy disk in drive A location to another to the C:\9700 directory. location. C:\>COPY A:\NODE1.* C:\9700 Copies all Ţles with the NODE1 root name from the ţoppy disk in drive A to the C:\9700 directory. C:\9700>COPY A:NODE1.* Copies all Ţles with the NODE1 root name from the ţoppy disk in drive A to the C:\9700 directory. A:\>COPY NODE1.* C:\9700 Copies all Ţles with the NODE1 root name from the ţoppy disk in drive A to the C:\9700 directory. C:\>COPY A:\*.* C:\9700 Copies all Ţles from the ţoppy disk in drive A to the C:\9700 directory. C:\9700>COPY NODE1.* A: Copies all Ţles with the NODE1 root name from the C:\9700 directory to the A drive. 68 C1572M (9/05) Table I. DOS Command Reference (Continued) † †† § Command Switch Description Example(s) ¶ File and Disk Management Commands (Continued) DEL Deletes a single Ţle or a C:\>DEL C:\9700\OLDFILE.MON Deletes the OLDFILE.MON Ţle group of Ţles from the from the C:\9700 directory. speciŢed location. C:\9700>DEL OLDFILE.MON Deletes the OLDFILE.MON Ţle NOTE: You can restore from the C:\9700 directory. deleted Ţles using the UNDELETE command. C:\>DEL A:OLDFILE.MON Deletes the OLDFILE.MON Ţle WARNING: Be careful from the ţoppy disk in drive A. that you do not delete A:\>DEL OLDFILE.MON Deletes the OLDFILE.MON Ţle necessary system or from the ţoppy disk in drive A. conŢguration Ţles. C:\9700>DEL OLDFILE.* Deletes all Ţles with the OLDFILE root name from the C:\9700 directory. /P Prompts you for conŢr- C:\9700>DEL OLDFILE.* /P Prompts you for conŢrmation mation before deleting a before deleting each Ţle with Ţle. the OLDFILE root name from the C:\9700 directory. EDIT Starts the MS-DOS C:\9700>EDIT STARTUP.BAT Allows you to edit the editor, which is a text startup.bat Ţle. editor that can be used to create and edit ASCII text Ţles. FORMAT Formats a disk for use C:\>FORMAT A: Formats the ţoppy disk in drive with DOS. If data is A for use with DOS. present on the disk, the data is erased. WARNING: Do not format the C: drive. /S Transfers operating sys- C:\>FORMAT A:\S Transfers operating system tem Ţles to a newly for- Ţles to a newly formatted matted ţoppy disk that ţoppy disk in drive A. can be used as the sys- tem disk, allowing you to boot from the disk. REN Changes the name of a —— single Ţle or a group of Ţles. For information about DOS Ţlename conventions, refer to the DOS Filename Conven- tions section. C1572M (9/05) 69 Table I. DOS Command Reference (Continued) † †† § Command Switch Description Example(s) ¶ File and Disk Management Commands (Continued) TYPE Displays the contents of C:\9700>TYPE NODE1.MON Displays the contents of the the speciŢed text Ţle on NODE1.MON Ţle located in the screen. If the loca- the C:\9700 directory tion of the Ţle is in a C:\>TYPE C:\9700\NODE1.MON Displays the contents of the directory other than the NODE1.MON Ţle located in one you are in, you must the C:\9700 directory specify the directory path. | MORE Allows a long text Ţle to C:\ TYPE C:\9700\NODE1.ALM | MORE Allows the NODE1.ALM text be viewed one screen at Ţle to be viewed one screen at a time. The | redirection a time operator symbol precedes the MORE command. The symbol is located above the backslash (\) on the keyboard. UNDELETE Recovers Ţles that were C:\UNDELETE C:\9700\TEST.BAT Recovers the TEST.BAT Ţle previously deleted using that was previously deleted the DEL command. using the DEL command. /LIST Lists the deleted Ţles C:\UNDELETE C:\9700\ /LIST Lists the Ţles that have been that are available to be deleted from the C:\9700 direc- recovered but does not tory and are available to be recover any Ţles. recovered but does not recover the Ţles. /ALL Recovers deleted Ţles C:\UNDELETE C:\9700\ /ALL Recovers all Ţles that have without prompting for been deleted from the C:\9700 conŢrmation for each directory without prompting Ţle for conŢrmation for each Ţle Environment Commands PATH Displays the current C:\>PATH — search path used when DOS looks for a program Ţle. PATH [drive:][path[;…]] Sets the search path to C:\>PATH C:;C:\DOS;C:\WINDOWS Sets the search path to be used when DOS C:;C:\DOS;C:\WINDOWS looks for a program Ţle Miscellaneous Commands CLS Clears the screen. Only C:\>CLS Clears the screen. The follow- the command prompt ing remains: C:\>_ and cursor remains. FASTHELP Lists and brieţy C:\>FASTHELP — describes MS-DOS commands. Provides less detail than the information provided by the HELP command (see below). 70 C1572M (9/05) Table I. DOS Command Reference (Continued) † †† § Switch Description Example(s) ¶ Command Miscellaneous Commands (Continued) FASTHELP command Brieţy describes the C:\FASTHELP DIR Displays brief information speciŢed command. about the DIR command. Provides less detail than the information provided by HELP command (see below). HELP Starts the MS-DOS C:\HELP — command reference, which provides detailed information about MS-DOS commands. HELP command Displays detailed C:\HELP DIR Displays detailed information information about the about the DIR command. speciŢed command only. MORE Displays one screen of C:\DIR C:\DOS | MORE Displays the contents of the information at a time. DOS directory one screen at a Can also be used with time. the TYPE command when viewing a long text Ţle. When MORE follows a command, the | redirection operator symbol is used. The symbol is located above the backslash (\) on the keyboard. VER Displays the current C:\VER — version of DOS. † DOS commands can be entered in lowercase or uppercase. †† A switch modiŢes the way DOS carries out a command. Generally, a switch consists of a forward slash (/) followed by one or more letters or numbers. § An asterisk (*) used in the examples denotes a wildcard. The asterisk matches any character in that position and all the positions that follow. The asterisk can be used to manage (for example, copy or delete) a group of conŢguration Ţles without the need to manage each conŢguration Ţle individually. NOTE: The root directory does not have a name. It is simply referred to as a backslash (\). Entering the CD\ command from any directory always returns you to the root directory, which is denoted by the command prompt C:\>. C1572M (9/05) 71 System Diagnostics The 9760 system provides diagnostic screens that allow you to monitor single-node and multi-node status. This section provides information about the following: • Monitoring CM9700-CC1 functions using the CM9700-CC1 diagnostic screen and associated PC keyboard commands • Viewing multi-node system status using the CM9700-NW1 diagnostic screen and associated PC keyboard commands NOTE: Additional displays, such as those provided by the CM9700-MGR Main window and the CM9760-KBD LCD, also provide information about system status. For detailed information, refer to the product-speciŢc documentation. MONITORING CM9700-CC1 FUNCTIONS The CM9700-CC1 provides a diagnostic screen that allows you to monitor CM9700-CC1 functions. You can view the diagnostic screen on a VGA monitor that is connected to the VGA port on the rear of the CM9700-CC1. The diagnostic screen appears after the CM9700-CC1 initializes. Refer to Figure 35 for a sample CM9700-CC1 diagnostic screen. MONITOR BOXES (8) CONFIGURATION INFORMATION CM9700-CC1 SOFTWARE VERSION GPI AND SYSTEM AUXILIARY BOX BOX Figure 35. Sample CM9700-CC1 Diagnostic Screen As illustrated in Figure 35, the CM9700-CC1 diagnostic screen displays the following items: • Monitor boxes: Up to eight monitor boxes are displayed on the CM9700-CC1 diagnostic screen at one time. Each monitor box represents a monitor and the camera currently being displayed on that monitor (for detailed information about the monitor box, refer to the Viewing Monitor Box Diagnostics section). • GPI and auxiliary box: Displays GPI and auxiliary information (if applicable): – GPI displays the GPI currently selected. The GPI number is updated when an auxiliary command is executed. – Ax displays the auxiliary currently selected and whether the auxiliary is on or off. • System box: Displays system status messages, error messages, and responses to commands issued from the PC keyboard that is connected to the AT-compatible port of the CM9700-CC1. • ConŢguration information: Indicates whether the CM9700-CC1 is part of a CM9760-HS hot switch conŢguration. Note that A OFF indicates that the CM9700-CC1 is not part of a hot switch conŢguration. (The letter A indicates asynchronous mode.) For detailed information about the diagnostic screen in a hot switch conŢguration, refer to the CM9760-HS Hot Switch Installation/Operation manual. • CM9700-CC1 software version: Displays the software version number (xxx xxx) of the CM9700.EXE executable Ţle (for example, version 903 023 which represents version 9.03.023). 72 C1572M (9/05) VIEWING MONITOR BOX DIAGNOSTICS The monitor box on the CM9700-CC1 diagnostic screen provides information about the monitor, camera, auxiliary conditions, and alarms currently being displayed. Refer to Figure 36 for a sample monitor box. LOGICAL ALARM NUMBER LOGICAL CAMERA FOCUS NUMBER INDICATION LINES CAMERA AUXILIARIES LOGICAL MONITOR ZOOM AND NUMBER JOYSTICK CONTROL BOX Figure 36. Sample Monitor Box on CM9700-CC1 Diagnostic Screen As illustrated in Figure 36, a monitor box displays the following information: • Logical camera number: IdentiŢes the logical number of the selected camera. Note that the letters CC denote that the camera is a controllable camera. If the letters CC do not appear for a particular camera, the camera is a Ţxed camera. • Camera auxiliary numbers 1-8: Indicate whether auxiliaries 1-8 are on or off. An auxiliary number appears white when the corresponding auxiliary is off and changes color when the corresponding auxiliary is turned on. • Logical monitor number: IdentiŢes the logical number of the selected monitor. • Logical alarm number: IdentiŢes the logical number of an alarm that has been triggered. • Focus indication lines: Indicate when a camera is focused near or far. When a camera is focused near, the distance between the lines increases. When a camera is focused far, the distance between the lines decreases. • Iris: Indicates when the iris of the camera is being opened or closed. When the iris is being opened, the black area inside the circle increases. When the iris is being closed, the black area decreases. • Zoom and joystick control box: Indicates when a camera is zoomed in or out. When a camera is zoomed in, the box becomes larger. When a camera is zoomed out, the box becomes smaller. The box also displays camera movement by mimicking joystick control. Note that each monitor box that is assigned to a camera is displayed in a color. The color of the monitor box changes when a different camera is selected. When a monitor box appears empty, a camera is not selected. C1572M (9/05) 73 ALLOCATING MONITORS TO MONITOR BOXES When the diagnostic screen appears on the VGA monitor after the CM9700-CC1 is initialized, the Ţrst eight monitors are displayed in the eight monitor boxes. Using the PC keyboard connected to the AT-compatible keyboard port of the CM9700-CC1, you can allocate a different monitor to a monitor box by using the function keys F1 through F8. The function keys correspond to the monitor boxes: • The top four monitor boxes are 1 to 4 (from left to right); therefore, F1 corresponds to monitor box 1, F2 corresponds to monitor box 2, and so on. • The bottom four monitor boxes are 5 to 8; therefore, F5 corresponds to monitor box 5, F6 corresponds to monitor box 6, and so on. To allocate a monitor to a monitor box, do the following: 1. Press the function key corresponding to the monitor box to which you want to want to assign a different monitor. For example, press F1 if you want to assign monitor box 1 a different monitor. In the System box, the following prompt appears: Allocate Box [x] to ? where x is the number of the desired monitor box (1-8). For example, pressing the F1 key causes the following prompt to appear: Allocate Box 1 to ? 2. Enter the number of the monitor you want to assign to the monitor box, and then press the Enter key. The desired monitor is displayed in the monitor box. 74 C1572M (9/05) ENTERING CM9700-CC1 PC KEYBOARD COMMANDS Using the PC keyboard connected to the AT-compatible keyboard port of the CM9700-CC1, you can enter commands to perform certain functions or to obtain system status information in the System box on the diagnostic screen. Refer to Table J for a list of CM9700-CC1 functions and associated PC keyboard commands. Table J. CM9700-CC1 PC Keyboard Command Functions Function Keyboard Command System Box Display Message Allocate monitor box 1 to 8 on diagnostic screen Function key F1 to F8, Example: Pressing F1 to allocate monitor box 1 results in which correspond to the following message: monitor box 1 to 8, Allocate Box 1 to ? respectively (Refer to the Allocating Monitors to Monitor Boxes section for additional information.) Stop system operation Ctrl+Q Exit to DOS prompt NOTE: When Ctrl+Q is entered, the 9760 system stops operating and the C:\9700 prompt appears. The CM9760-KBDs go ofţine and the time and date titling on the monitor outputs from the CM9760-MXB stop at XX:XX:59. Operators then lose control of the system. It is recommended that system operation be stopped during off-peak hours if possible. Display number of messages to be printed Alt+O Total Ptr Msg => 0 NOTE: Printer port is reserved for future use. Display port parameters Alt+A Example: 1 - ATNRQ (IRQ 10) Connected to SER1 NOTE: Toggling the Alt+A key combination cycles through all allocated IRQs and associated connections as conŢgured. Display operator logged-on parameters Alt+J Example: LogOn–Opr1, KB2,Pin1111,Port 7,index2 NOTE: Toggling the Alt+J key combination cycles through operators. Display system alarm parameters Alt+K Example: Sys:3 Auto:0 1 Alt+Z Example: (10,0) (10,0) (10,0) (10,0) Display/set time adjustment parameters Alt+L Last Adj. 0 : 0. 0 Total 0: 0 . 0 (Refer to the System Programming Using DOS section for detailed information about setting and adjusting time in a single-node system.) Shift+ESC Last Adj. 0 : 0. 0 Total 0: 0 . 0.60 NOTE: The Shift+ESC command must follow the Alt+L command. Display operator alarm parameters Alt+C Example: Kb2 Alms 0 Alarm 0 0 0 0 FI0 0 0 Display alarm sequence parameters Alt+B Cur0, Alms0-0 0 0 0 Cams0-0 0 0 0 Display conŢguration Ţlename Alt+N Example: ConŢguration Ţle is NODE1 Display number of peripheral devices connected to the Alt+V Example: Port10 Node1 NIU0 Cam16 Mon8 Kbd11 system NOTE: Continue toggling for entire list of peripheral devices. Toggle printer port on/off Alt+P Printer not allocated NOTE: Printer port is reserved for future use. C1572M (9/05) 75 Table J. CM9700-CC1 PC Keyboard Command Functions (Continued) Function Keyboard Command System Box Display Message Toggle system error printing on/off Alt+R System Error Print ON or System Error Print OFF NOTE: Printer port is reserved for future use. Toggle system synchronization diagnostic trap on/off Alt+T Resynch Trap Ofţine or Resynch Trap Online Toggle system diagnostics on/off. When system diag- Alt+D Demo On nostics is off, the diagnostic screen is visible but is not or updated. Demo Off Toggle system error reporting on/off. When system error Alt+S System on reporting is off, the System box is not updated with or system error messages. When a visual display of error System off reporting is not necessary, it is recommended that error reporting be turned off to reduce system load. Toggle between master/slave units, PC keyboard, and Alt+M — monitor using ChangeOver system Trigger alarm points 1 to 9 (test function) Shift + function key F1 — to F9, which corre- spond to alarm points 1 to 9, respectively Clear message displayed in System box Space bar — 76 C1572M (9/05) VIEWING MULTI-NODE SYSTEM STATUS The CM9700-NW1 provides a diagnostic screen that displays multi-node system status during the initialization of the CM9700-NW1 and any changes in system status that occur after the initialization process. Refer to Figure 37 for a sample CM9700-NW1 diagnostic screen. PELCO CM9700 N.I.U. Ver xxx xxx Vector initialized 2nodes.niu Com init COM1 ATNRQ 3 (IRQ 5) Connected to _ _ _ _ ATNRQ 4 (IRQ 10) Connected to SER 1 ATNRQ 6 (IRQ 11) Connected to SER 2 ATNRQ 7 (IRQ 12) Connected to SER 3 ATNRQ 5 (IRQ 7) Connected to _ _ _ _ ATNRQ 2 (IRQ 4) Connected to COM 1 ATNRQ 1 (IRQ 3) Connected to _ _ _ _ ATNRQ 0 (IRQ 15) Connected to _ _ _ _ Fri Jul 23 11:46:10 2005 Port 8 Request download Fri Jul 23 11:46:11 2005 Port 8 on line Fri Jul 23 11:47:13 2005 Port 8 Receiving Monitor parameters Fri Jul 23 11:47:16 2005 Port 8 Receiving Camera parameters Fri Jul 23 11:47:17 2005 Port 8 Received Tie Line parameters Fri Jul 23 11:47:18 2005 Port 8 Received Operator parameters Figure 37. Sample CM9700-NW1 Diagnostic Screen As the CM9700-NW1 initializes, the SERCOM ports of the CM9700-NW1 are set up according to the CM9700-NW1 conŢguration Ţle. The CM9700-NW1 then polls each of the SERCOM ports and requests download information about the setup of each port. As shown in Figure 37, the CM9700-NW1 diagnostic screen displays the hardware conŢguration of the CM9700-NW1 and then displays the downloaded information about each of the SERCOM ports connected to a CM9700-CC1 as each port is polled. The CM9700-NW1 reports that a port is online (for example, port 8 is online) and displays the status of setup information for the port (for example, received operator parameters). In addition, date and time information is also displayed for each status condition. The CM9700-NW1 continues to poll until each port connected to a CM9700-CC1 has responded with the download information. The diagnostic screen also indicates when the CM9700-MGR PC, referred to as the Admin PC, goes online. The CM9700-NW1 diagnostic screen changes only when a change in system status occurs. For example, if port 8 is online (as shown in Figure 37) but then goes ofţine, the diagnostic screen then displays the ofţine condition including the date and time of the occurrence: Fri Jul 24 15:23:13 2005 Port 8 off line When port 8 goes online, the diagnostic screen then displays the online condition including the date and time of the occurrence: Fri Jul 24 16:20:23 2005 Port 8 on line The diagnostic screen also indicates a change in status of the CM9700-MGR PC. For example, the diagnostic screen displays the following when the CM9700-MGR PC goes ofţine and then back online: Fri Jul 23 16:21:32 2005 Admin PC off line Fri Jul 23 16:30:24 2005 Admin PC on line C1572M (9/05) 77 ENTERING CM9700-NW1 PC KEYBOARD COMMANDS Using the keyboard connected to the AT-compatible keyboard port of the CM9700-NW1, you can enter commands to perform certain functions. Refer to Table K for a list of CM9700-NW1 functions and associated keyboard commands. Table K. CM9700-NW1 PC Keyboard Command Functions Function Keyboard Command Display operator/node information Alt+O Display/set time adjustment parameters* Alt+L Display system version level Alt+N Display tie line information Alt+T Display updated tie line information Alt+X Toggle CM9700-NW1 system diagnostics on/off. When system diagnostics is off, the CM9700-NW1 Alt+S diagnostic screen is visible but is not updated. Stop operation of the CM9700-NW1 (operation of Ctrl+Q CM9700-CC1 nodes continue) *Refer to the System Programming Using DOS section for detailed information about setting and adjusting time in a multi-node system. 78 C1572M (9/05) Troubleshooting This section provides the following troubleshooting information for the 9760 system: • General troubleshooting guidelines • CM9700-CC1 hardware and system error troubleshooting • CM9760-MXB troubleshooting using the CM9760-MXB LEDs For additional troubleshooting information relating to other 9760 system devices, refer to the manual supplied with the device. GENERAL TROUBLESHOOTING GUIDELINES Begin troubleshooting a problem with the 9760 system by perform the following troubleshooting steps as appropriate: 1. Ensure that all power cords are attached. 2. Ensure that all power switches are in the ON position. 3. Ensure that all cables are installed in the proper location and are fully seated. 4. Ensure that all cards are installed in the proper location and are fully seated. 5. Ensure that all DIP switches and jumpers are properly set. TROUBLESHOOTING THE CM9700-CC1 Problems with the CM9700-CC1 may occur due to the following: • CM9700-CC1 hardware errors (refer to Table L) • CM9700-CC1 system errors, which are are displayed as error messages in the System box on the CM9700-CC1 diagnostic screen (refer to Table M) • CM9700-CC1 conŢguration Ţle errors • DOS operating system errors, which are displayed on the VGA monitor as the CM9700-CC1 initializes • Peripheral devices connected to the CM9700-CC1 Table L. CM9700-CC1 Hardware Error Troubleshooting Hardware Error Possible Cause Corrective Action Green power LED does not light. No AC power to the unit Check power cord connection. Blown fuse Replace fuse. VGA monitor display does not appear. Video cable not seated properly Check cable connection to VGA port. Power cord not connected Connect power cord. Defective VGA card Replace VGA card. C1572M (9/05) 79 Table M. CM9700-CC1 System Error Troubleshooting System Error Message Possible Cause Corrective Action Port x ERR Coms Framing Mismatched baud rate settings Correct the baud rate setting in the CM9700-MGR to match the settings in the device connected to the speciŢed port. Port x ERR Coms Fatal Failure of communications line after power Check and correct hardware fault. up and initialization Port x ERR Coms Parity Mismatched parity settings Correct the parity setting in the CM9700-MGR to match the settings in the device connected to the speciŢed port. Port x ERR Coms Max Retry If the communications line is faulty (wired Check and correct hardware fault. incorrectly or not seated properly), the diagnostic screen displays this error. If the communications line fails after power-up and initialization, then a Port x ERR Coms Fatal error appears, followed by a Port x ERR Max Retry message. Temporary communications fault Fault will automatically be corrected when communications resume. Noise on the data line Check data cables. 80 C1572M (9/05) TROUBLESHOOTING THE CM9760-MXB If a problem exists with the matrix bay, reset operation of the unit by pressing the Reset button located on the front of the CM9760-VMC video output card. All information, such as camera and monitor idents, is reloaded from the CM9700-CC1. If the problem still exists, refer to Table N for additional troubleshooting information. Table N. Troubleshooting Using CM9760-MXB Diagnostic LEDs LED Color Possible Cause Corrective Action CM9760-VCC Video Input Card LEDs +10 VDC Power LED (CR2) not lit Defective fuse(s) on CM9760-VCC card Remove and inspect fuses on card. Replace fuse if defective. -10 VDC Power LED (CR3) not lit Defective fuse(s) on CM9760-VCC card Remove and inspect fuses on card. Replace fuse if defective. Red Comm Fail LED (CR1) Card not seated properly Reseat the card. Defective CM9760-VCC card Replace the card. Red Comm Fail LEDs on all CM9760-VCC CM9760-VMC video output card must be Press the Reset button on the CM9760-VMC cards. (Red Comm Fail LED also on reset. card. If all Comm Fail LEDs remain red, the CM9760-VMC) CM9760-VMC card is defective. Defective CM9760-VMC card Replace the card. CM9760-VMC Video Output Card LEDs +10 VDC power LED (DS5) not lit Defective fuse(s) on CM9760-VMC card Remove and inspect fuses on card. Replace fuse if defective. -10 VDC power LED (DS4) not lit Defective fuse(s) on CM9760-VMC card Remove and inspect fuses on card. Replace fuse if defective. Red Comm Fail LED (DS6) on CM9760-VMC Cable between the CM9760-MXB and the Check cable connections. Check that cable is only CM9700-CC1 is not connected properly or is connected to correct CM9700-CC1 port. not installed in the proper location. Incorrect wiring of cable Check wiring of cable if not using supplied data communication cable. Port communication setup is incorrect, for Check port conŢguration settings in example, incorrect baud rate or device type CM9700-MGR. Power Supply Module LEDs +10V Power LED not lit Power supply not seated properly Ensure that power supply is seated properly. Blown fuse Replace fuse. -10V Power LED not lit Power supply not seated properly Ensure that power supply is seated properly. Blown fuse Replace fuse. Flashing red Frame Fault LED Failure of one or more video input/output Refer to the CM9760-VCC Video Input Card cards. Refer to the CM9760-VCC Video Input LEDs and CM9760-VMC Video Output Card Card LEDs and CM9760-VMC Video Output LEDs sections above for corrective actions. Card LEDs sections above for possible causes. Red Supply Fault LED Failure of associated power supply module Replace power supply module. C1572M (9/05) 81 CM9700-CC1 Controller This section provides detailed information about the CM9700-CC1. The following information is provided: • Description of the functions of the CM9700-CC1 • Front and rear views of the CM9700-CC1 • Description of the DOS directory structure of the CM9700-CC1 NOTE: For CM9700-CC1 installation information, refer to the System Setup and CM9700-CC1 Component Installation or Replacement sections. DESCRIPTION The CM9700-CC1 is the central processing unit (CPU) of the 9760 system. All components of the 9760 system connect to and communicate with the CM9700-CC1. The CM9700-CC1 runs under DOS 6.22. For a description of the DOS directory structure of the CM9700-CC1, refer to the Directory Structure section. Note the following: • To ensure uninterrupted operation, a backup CM9700-CC1 can be added to a 9760 system by means of the CM9760-HS hot switch. For additional information, refer to the System 9760 CM9760-HS Hot Switch Installation/Operation manual. • The CM9700-CC1 can be networked by means of the CM9760-NW1 network interface unit (NIU). For additional information, refer to the System 9760 Networking Guide. 82 C1572M (9/05) FRONT VIEW Figure 38 illustrates the front of the CM9700-CC1. MOUNTING HANDLES DOOR KNOB CM9700-CC1 FRONT VIEW WITH DOOR CLOSED HARD DISK KEYBOARD POWER DRIVE LED RESET PORT LED (NOT USED) BUTTON FLOPPY DISK DRIVE CM9700-CC1 FRONT VIEW WITH DOOR OPEN Figure 38. CM9700-CC1 Front View Note the following: • The door of the CM9700-CC1 is secured by a Phillips-head screw on the knob. To open the door, loosen the screw on the knob. • In addition to the AT-compatible keyboard port on the front of the CM9700-CC1, another AT-compatible keyboard port is located on the rear of the unit. Both keyboard ports cannot be used at the same time. • The power LED lights green to indicate that AC power is being applied to the unit. • Because of the solid state ţash memory of the CM9700-CC1, the hard disk drive LED is not used. C1572M (9/05) 83 REAR VIEW Figure 39 illustrates the rear of the CM9700-CC1. COM 2 COM 1 SERCOM PORT PORT VGA PORTS PRINTER (RS-232) PORT* (RS-232) PORT (RS-422) 36 28 20 12 35 27 19 11 18 10 34 26 33 25 17 9 24 32 16 8 31 23 15 7 14 30 22 6 PRINTER COM1 COM2 29 21 13 5 POWER POWER AT-COMPATIBLE INPUT SWITCH KEYBOARD PORT *RESERVED FOR FUTURE USE Figure 39. CM9700-CC1 Rear View As illustrated in Figure 39, the rear of the CM9700-CC1 includes the following: • Printer port: Female DB25 connector (reserved for future use) • Physical ports 1-2 and 5-36: – COM 1 (port 1) and COM 2 (port 2): Male DB9 connectors for RS-232 serial communication. COM 1 is configured at the factory for connection to the CM9700-MGR PC. – Serial communication (SERCOM) ports 5-36: Female RJ-45 connectors for RS-422 communication to system devices such as CM9760-MXBs and CM9760-KBDs. The default conŢguration of the CM9700-CC1 contains 16 SERCOM ports (ports 5-20). The ports are provided by two CM9700-SER serial communication cards installed on the CM9700-CC1 motherboard. Each card provides 8 SERCOM ports. Depending on system requirements, up to two additional CM9700-SER cards can be ordered, providing up to 16 additional ports (ports 21-36). If four CM9700-SER cards are installed, the total number of SERCOM ports is 32. For information about adding or replacing CM9700-SER cards in an existing system, refer to Installing or Replacing a CM9700-SER Card in the CM9700-CC1 Component Installation or Replacement section. Note that a maximum of 120 SERCOM ports can be achieved with a conŢguration of 3 CM9700-SER cards (8 ports each) and 3 CM9700-SER-32 port expander assemblies (32 ports each). For information about CM9700-SER-32 port expander assemblies, refer to the CM9700-SER-32 Port Expander Installation/Operation manual. NOTE: Ports 3 and 4 are not present on the CM9700-CC1. • VGA port: Female DB15 connector that connects to a VGA monitor, which allows you to view system diagnostics. For additional information about system diagnostics, refer to the System Diagnostics section. • AT-compatible keyboard port: 5-pin mini DIN connector that connects to the supplied PS/2-to-AT keyboard adapter for connection to the supplied PS/2 keyboard. NOTE: An AT-compatible keyboard port also exists on the front of the CM9700-CC1 behind the front door (refer to Figure 38). Both keyboard ports cannot be used at the same time. • AC power input connector: Three-prong connector that connects to the supplied power cord. The acceptable power range is 120 VAC to 230 VAC. The power supply automatically adjusts to the proper voltage range. • Power switch: Rocker-type switch used to power the CM9700-CC1 on or off. Figure 40 illustrates pinouts of connectors on the rear of the CM9700-CC1. 84 C1572M (9/05) PIN 1 PIN 14 5-PIN “MINI-DIN” KEYBOARD CONNECTOR PIN 1 25-PIN “D” TYPE PIN 3 CONNECTOR (PRINTER PORT) PIN 4 PIN 5 (FEMALE) PIN 2 (RESERVED FOR FUTURE USE) PIN 1 = KEYBOARD CLOCK PIN 2 = KEYBOARD DATA PIN 3 = NOT USED PIN 4 = GND PIN 5 = +5V PIN 13 PIN 25 COM 1 (MALE) COM 2 (MALE) 8-PIN SERCOM PORT PINOUTS SAME (FEMALE) AS COM 1 PIN 5 PIN 9 PIN 1 = TX+ PIN 1 PIN 2 = TX- PIN 7 = RX- PIN 8 PIN 8 = RX+ PIN 1 PIN 6 WHEN A SERCOM PORT IS USED TO INTERFACE MULTIPLE RECEIVERS VGA PORT (FEMALE) OR DOMES (THAT IS THOSE WITH PTZ CONTROL), THEY SHOULD BE WIRED AS DEPICTED BELOW. PIN 10 PIN 15 PIN 5 = TAP OFF CONNECTIONS PIN 1 TX- PIN 2 TX+ NOTE: THE DISTANCE, SERCOM PORT “D”, BETWEEN THE INDICATED TAP-OFF D RX/DR RX/DR RX/DR CONNECTIONS AND PIN 11 PIN 1 OR OR OR THEIR ASSOCIATED DOME 1 DOME 2 DOME 3 PIN 6 RX/DR OF DOME CONNECTIONS SHOULD BE 3 FEET (0.91 M) OR LESS Figure 40. CM9700-CC1 Rear Connector Pinouts C1572M (9/05) 85 DIRECTORY STRUCTURE The directory structure of the CM9700-CC1 consists of the C:\ root directory, which contains several subdirectories and Ţles. You can view the contents of the root directory by entering dir and then pressing Enter at the C:\ prompt (refer to Figure 41). 11:16:15.93 Tue 07-19-2005 C:\>dir Volume in drive C has no label Volume Serial Number is 1B13-0FD8 Directory of C:\ COMMAND COM 54,645 05-31-94 6:22a WINA20 386 9,349 05-31-94 6:22a TVDISP EXE 13,608 02-26-97 2:25p CONFIG SYS 82 10-14-97 10:03a README TV 1,873 07-23-99 4:55p AUTOEXEC BAT 73 07-19-05 11:05a 9700