INSTALLATION/OPERATION CM9760-KBD/ CM9760-KBR Series ™ System 9700 Intelligent Keyboard C540M-D (3/06) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Activating Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Changing the Setup PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Changing the Define PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Calibrating the Joystick Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Calibrating the Joystick Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Adjusting the Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Direct Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Direct Camera Control for Non-Pelco MUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Configuring the Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Adjusting the Time Out Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Setting the Control Keys Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Downloading Keyboard Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Downloading Keyboard to Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Downloading Through the CM9700 Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Uploading to the MGR Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Activating Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Selecting Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Selecting Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Locking Cameras or Input Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Overriding Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Overriding Camera Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Group Input Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Selecting Group Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Operating PTZ Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Advanced Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Creating Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Recalling Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Deleting Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Creating a Preset Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Assigning a Preset Label to a Preset Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Recalling Defined Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Creating a Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Recalling a Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Creating a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Partial Zone Overlap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Embedded Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 C540M-D (3/06) 3 Turning Zones On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Erasing Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 DVR and VCR Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 GPI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 MUX Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Loading Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Pausing a Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Deleting a Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Creating a Temporary Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Setting the Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Video Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Arming Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Disarming Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Resetting Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Diagnostics Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Testing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Testing the Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Testing the DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 4 C540M-D (3/06) List of Illustrations 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 CM9760-KBD Top View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3 CM9760-KBD Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 4 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 5 Enter Setup Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 6 Setup Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 7 Advance Setup 1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 8 Advance Setup 4 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 9 Joystick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 10 LCD Brightness Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 11 Direct Mode Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 12 Advance Setup 1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 13 Direct Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 14 COM 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 15 Baud and Parity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 16 Direct Camera Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 17 Camera Assign Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 18 Logical Number Entered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 19 Logical Number Assigned. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 20 AUX Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 21 Port ConŢguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 22 Direct Camera Control (Non-Pelco MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 23 COM Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 24 MUX Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 25 Cameras Per Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 26 Advance Setup 2 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 27 Advance Setup 3 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 28 Key DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 29 Key Not DeŢned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 30 Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 31 Keyboard Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 32 Target Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 33 System Download/Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 34 Node Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 35 Setup Mode Exit Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 36 Log In Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 37 PIN Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 38 Monitor Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 39 Monitor Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 40 Monitor Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 41 Monitor 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 42 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 43 Main Menu Camera Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 44 Camera Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 45 Camera Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 46 DeŢne PIN Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 47 DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 48 Preset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 49 Preset Label Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 50 DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 51 Pattern DeŢnition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 52 Preset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 53 DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 54 DeŢne Zone Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 55 Zone Label Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 56 Character Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 57 Basic Zone Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 C540M-D (3/06) 5 58 Partial Zone Overlap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 59 Embedded Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 60 DVR Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 61 VCR Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 62 GPI Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 63 MUX Control Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 64 Macro Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 65 DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 66 Macro DeŢne Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 67 Macro DeŢne Menu 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 68 Macro DeŢne Menu 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 69 Temporary Macro Step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 70 Time and Date Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 71 Hours and Minutes Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 72 Video Loss Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 73 Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 74 Triggered Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 75 Verify Logoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 76 Diagnostic Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 77 LCD Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 78 Keyboard Test Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 79 DIP Switch Test Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 List of Tables A GPI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 B MUX Control Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 6 C540M-D (3/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliŢers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A sgrounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not Ţt into your outlet consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus. 11. Only use attachments/accessories speciŢed by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table speciŢed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualiŢed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Apparatus shall not be exposed to dripping or splashing and that no objects Ţlled with liquids, such as vases shall be placed on the apparatus. 16. WARNING: To reduce the risk of Ţre or electric shock, do not expose this apparatus to rain or moisture. 17. A CCC-approved power cord must be used to power this equipment when used in China. C540M-D (3/06) 7 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes and ModiŢcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules. In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 8 C540M-D (3/06) Before You Begin Make sure the following parts are present before you install and operate your CM9760-KBD keyboard. PARTS LIST Qty Description 1 CM9760-KBD/KBR keyboard* 1 RJ-45 straight cable 1 RJ-45 reversed cable 1 Power supply (KBD-PS-1) with power cord** 1 Installation/Operation manual *The CM9760-KBR is not pictured in Figure 1. It is the same as the CM9760-KBD except rack mountable. Refer to page 10 for all keyboard models. **Customers in the US, UK, Australia, and Europe will receive one of the four power cords shown in Figure 1. PACKAGE CONTENTS RJ-45 REVERSED CABLE RJ-45 STRAIGHT CABLE 1 EA. 1 EA. SHIPPING BOX MANUAL 1 EA. CM9760-KBD POWER SUPPLY US POWER CORD UK POWER CORD AU POWER CORD EU POWER CORD 1 EA. (KBD-PS-1) (US-320-C5) (UK-320-C5) (AU-320-C5) (EU-320-C5) 1 EA. 1 EA. 1 EA. 1 EA. 1 EA. Figure 1. Package Contents C540M-D (3/06) 9 Description The CM9760-KBD is a full-function desktop keyboard that allows you to control matrix systems, such as the CM9760, CM9770, and CM9780. The CM9760-KBR rack-mount model is also available and has the same features as the CM9760-KBD. It Ţts into a 19-inch, EIA-standard rack (4 RUs). You can control GPI-activated devices, receivers, camera/monitoring switching, and multiplexer screen functions, and create single/dual patterns, zones, zone labels, presets, and preset recalls. The keyboard has a variable-speed joystick with a zoom control knob for pan/tilt/zoom (PTZ) and dome control. It also has 24 programmable soft keys. The keyboard has these additional features. • Easy to use LCD display with icons • Arm and disarm alarms • Create and execute macros • Download user-deŢnable key conŢgurations to and from other keyboards NOTE: The CM9760-CC1 has been replaced with the CM9700-CC1 and the CM9760-MGR management software has been replaced with the CM9700-MGR management software. MODELS CM9760-KBD-US Programmable keyboard; 100-240 VAC, 50/60 Hz CM9760-KBD-UK Same as CM9760-KBD-US except for use in the United Kingdom CM9760-KBD-AU Same as CM9760-KBD-US except for use in Australia CM9760-KBD-EU Same as CM9760-KBD-US except for use in Europe CM9760-KBR-US Same as CM9760-KBD-US except rack mountable CM9760-KBR-UK Same as CM9760-KBD-UK except rack mountable CM9760-KBR-AU Same as CM9760-KBD-AU except rack mountable CM9760-KBR-EU Same as CM9760-KBD-EU except rack mountable 10 C540M-D (3/06) TOP VIEW � �� � � � � � � Figure 2. CM9760-KBD Top View � LCD Display � Multipurpose Function Keys � Escape Key � Control Keys (F1-F24) � Keypad (0-9, camera key, monitor key) � Function Control Keys Bwd key: backward step through available camera selections Fwd key: forward step through available camera selections Run key: run a paused macro Mac key: selection, creation, and execution of macros Rcl/Alt key: • Rcl: recall previous selections • Alt: cycle through inputs associated with selection Prst/Lock key: • Prst: recall preset • Lock: lock/unlock cameras to monitors � Lens Control Keys (zoom in or out, focus near or far, open or close iris) � Turbo Key � Joystick C540M-D (3/06) 11 In Near Rct Prst Open 1 T 3 2 esc 4 9 Bwd Fwd Run 6 8 0 5 7 Mac CAM MON Lock Out Far Close Alt BOTTOM VIEW � � ��� � � � Figure 3. CM9760-KBD Bottom View � COM 1 Port � COM 2 Port � COM 3 Port 2 � 1 C Bus (not used) � Relay Port � DIP Switches � Reset Key (recessed) � Volume Knob 12 C540M-D (3/06) Installation CONNECTIONS 1. Make sure all DIP switches are OFF. 2. Connect the RJ-45 straight cable from the COM 1 port on the keyboard to the “Keyboard” connector on the power supply. 3. Connect the RJ-45 reversed cable from the “System” connector on the power supply to a SERCOM port on the CC1. 4. Plug in the power supply. 5. Turn the main power supply switch ON. RJ-45 STRAIGHT CABLE PORTS 5 -12 SERCOM BOARD (LOCATED IN CM9700-CC1) POWER SUPPLY COM 1 PIN 1 PIN 8 COM 3 (BOTTOM OF CM9760-KBD) SERCOM PORT 5 RJ-45 REVERSED CABLE Figure 4. Connections NOTE: You can also hook up an alternate connection (RS-232) from COM 3 on the keyboard to COM 1 or COM 2 on the back of the CM9700-CC1. The cable going from COM 1 to the power supply is still required for keyboard power. With an RS-232 connection, the effective operating distance between the keyboard and CC1 is about 50 feet. C540M-D (3/06) 13 ACTIVATING SETUP MODE To conŢgure the keyboard, you must activate Setup Mode. 1. Set DIP switch 2 ON. The following appears on the LCD display. ENTER SETUP PIN Figure 5. Enter Setup Pin 2. Enter 1234. This is the default setup PIN. The Setup Mode Menu appears with the version number. SETUP MODEv8.24 JSTK LCD ADV Figure 6. Setup Mode Menu CHANGING THE SETUP PIN To change the default setup PIN: 1. Select . The Advance Setup 1 Menu appears on the LCD display. Advance Setup 1 >Host System 9750/60 Even (Host) COM 1 4800 COM 2 4800 Even Even COM 3 4800 SAVE Figure 7. Advance Setup 1 Menu 2. Select or until you get to the Advance Setup 4 Menu. Advance Setup 4 Setup Pin **** > Confirm **** Define Pin **** Confirm **** DEF SAVE NUM Figure 8. Advance Setup 4 Menu 3. Select , enter a four-digit PIN, and then select . 4. Select to go to ConŢrm. 14 C540M-D (3/06) 5. Select , enter the PIN again, and then select . “OK” appears on the ConŢrm line. 6.Select . You can also change the DeŢne PIN from the same menu. CHANGING THE DEFINE PIN A PIN is required to use the features that are accessible via the DeŢne Menu. The DeŢne PIN is used in the operation mode to access extended keyboard functions and for initial access to ARM/DISARM alarm functions. The default DeŢne PIN is 1234. To change the default DeŢne PIN: 1. Move the cursor to DeŢne Pin. 2. Select , enter a four-digit PIN, and then select . 3. Move the cursor to ConŢrm. 4. Select , enter the PIN again, and then select . “OK” appears on the ConŢrm line. 5. Select and then . CALIBRATING THE JOYSTICK MANUALLY Automatic joystick calibration is the factory default, but you can change the joystick calibration settings manually. You no longer have to verify the value for each joystick position. 1. Select from the Setup Mode Menu. The Joystick Setup Menu appears on the LCD display. JOYSTICK SETUP xxx xxx (xxx,xxx) xxx xxx SAVE Figure 9. Joystick Setup Menu 2. With the joystick in the center, select . 3. Move the joystick fully left, and select . 4. Move the joystick fully right, and select . 5. Move the joystick fully down, and select . 6. Move the joystick fully up, and select . 7. Select and then . C540M-D (3/06) 15 CALIBRATING THE JOYSTICK AUTOMATICALLY This is the factory default calibration mode for all CM9760-KBD keyboards. Follow these steps if you change the joystick calibration mode to manual and want to go back to automatic joystick calibration. 1. Select from the Setup Mode menu. 2. With the joystick in the center, select and then to activate automatic calibration mode. 3.Select . The joystick calibrates automatically every 30 minutes with no additional user action required. ADJUSTING THE DISPLAY BRIGHTNESS 1. Select from the Setup Mode Menu. The LCD Brightness Setup Menu appears on the LCD display. LCD BRIGHTNESS SETUP SAVE Figure 10. LCD Brightness Setup Menu 2. Select or to adjust the display brightness. 3. Select and then . NOTE: The display brightness can also be adjusted by selecting from the DeŢne Menu. 16 C540M-D (3/06) DIRECT CAMERA CONTROL Cameras can be connected directly to COM 1 and/or COM 2 located on the bottom of the CM9760-KBD. Up to 16 cameras can be connected to each port for a total of 32. Follow these steps and refer to Figure 11. ® ® NOTE: Use cameras that have RS-422 Pelco P-type protocol. This includes most Legacy , Intercept , and System 9750/9760 ERD receivers. POWER SUPPLY PIN 1 TX + PIN 1 TX + COM 2 COM 1 PIN 2 TX - PIN 2 TX - PELCO CM9760-KBD RECEIVER RECEIVER RECEIVER RECEIVER DIRECT MODE HOOKUP UP TO 16 RECEIVERS UP TO 16 RECEIVERS RECEIVER AND ASSOCIATED AND ASSOCIATED RECEIVER CAMERA INPUTS CAMERA INPUTS Figure 11. Direct Mode Connection 1. Select from the Setup Mode Menu. The Advance Setup 1 Menu appears on the LCD display. The cursor is on the Host row. Advance Setup 1 >Host System 9750/60 COM 1 4800 Even (Host) Even COM 2 4800 COM 3 4800 Even SAVE Figure 12. Advance Setup 1 Menu 2. Select or to choose Direct Cam Ctrl. Advance Setup 1 >Host Direct Cam Ctrl COM 1 4800 Even Even COM 2 4800 COM 3 4800 Even SAVE Figure 13. Direct Camera Control C540M-D (3/06) 17 3. Select to choose the COM port you are going to conŢgure. The Ţgure below shows the COM 1 port. Advance Setup 1 Host Direct Cam Ctrl Even >COM 1 4800 COM 2 4800 Even Even COM 3 4800 SAVE Figure 14. COM 1 4. Select or to choose the baud rate and to choose the parity. In the Ţgure below, a 9600 baud rate and Odd parity has been chosen for COM 1. Advance Setup 1 Host Direct Cam Ctrl COM 1 9600 Odd > Even COM 2 4800 COM 3 4800 Even SAVE Figure 15. Baud and Parity 5. Select and then to return to the Setup Mode Menu. 6. Select . The Direct Camera Control Menu appears on the LCD display. Direct Camera Control >COM 1 PELCO COM 2 PELCO COM 3 None Cam Per Mux 16 SAVE Figure 16. Direct Camera Control Menu 7. Select or to choose Pelco for COM 1. 8. Select to go to the Camera Assign Menu to assign all the physical ports with logical numbers and assign the status of any existing AUX’s. Camera Assign Physical Logical 1 2 3 4 5 6 7 8 > 0 0 T T T T M M M M 1 0 T T T T M M M M 2 0 T T T T M M M M 3 0 T T T T M M M M SAVE AUX Figure 17. Camera Assign Menu 9. Select to assign camera logical numbers. 18 C540M-D (3/06) 10. Enter a logical number for the physical port. In the Ţgure below, 10 has been entered. Camera Assign Physical Logical 1 2 3 4 5 6 7 8 > 0 10 T T T T M M M M 1 0 T T T T M M M M 2 0 T T T T M M M M 3 0 T T T T M M M M SAVE AUX Figure 18. Logical Number Entered 11. Select . The number is placed into the selected row for logical numbers. Camera Assign Physical Logical 1 2 3 4 5 6 7 8 > 0 10 T T T T M M M M 1 0 T T T T M M M M 2 0 T T T T M M M M 3 0 T T T T M M M M SAVE AUX Figure 19. Logical Number Assigned 12. Select to set up the relay AUX functions for T (toggle) or M (momentary). The following appears on the LCD display. Camera Assign Physical Logical 1 2 3 4 5 6 7 8 0 10 T T T T M M M M > 1 0 T T T T M M M M 2 0 T T T T M M M M 3 0 T T T T M M M M 1 2 3 4 5 6 7 8 Figure 20. AUX Functions NOTE: Each of the eight AUX icons controls settings for one relay (T or M). 13. Select an AUX icon, for example , to change the toggle setting between T and M. esc 14. Press and then select to go to the next port you want to conŢgure. The Ţgure below shows Port 1. Camera Assign Physical Logical 1 2 3 4 5 6 7 8 0 10 T T T T M M M M 1 0 T T T T M M M M > 2 0 T T T T M M M M 3 0 T T T T M M M M SAVE AUX Figure 21. Port ConŢguration esc 15. When you are Ţnished conŢguring the last port’s AUX, press and then select . NOTE: You will enter Direct Camera Control Mode when you exit Setup Mode. You will be able to operate cameras directly from the CM9760 keyboard. C540M-D (3/06) 19 DIRECT CAMERA CONTROL FOR NON-PELCO MUX In the Direct Camera Control Menu, COM 3 has a default of NONE. You can select and conŢgure the following MUX types: Montage, Robot, and Drax. Direct Camera Control >COM 1 PELCO COM 2 PELCO COM 3 None Cam Per Mux 16 SAVE Figure 22. Direct Camera Control (Non-Pelco MUX) 1. Select to go down to COM 3. Direct Camera Control COM1 PELCO COM2 PELCO >COM3 None Cam Per Mux 16 SAVE Figure 23. COM Port 2. Select or to select the MUX type. Direct Camera Control COM1 PELCO COM2 PELCO >COM3 Robot Cam Per Mux 16 SAVE Figure 24. MUX Type NOTE: Be careful when selecting and saving a MUX. You cannot change your selection without Ţrst recycling power on the keyboard. 3. Select to go down to the “Cam per MUX” line. Direct Camera Control COM1 PELCO COM2 PELCO COM3 Robot > Cam Per Mux 16 SAVE Figure 25. Cameras Per Multiplexer 4.Select . 5. Enter a number for the number of cameras to be connected to the MUX. Figure 25 shows 16 cameras. 6.Select again. 7. Select and then . 20 C540M-D (3/06) CONFIGURING THE RELAYS Each CM9760-KBD keyboard has two relays that can be used with macros stored in the connected system, which will typically be the CM9700-CC1. Macros are used to automate sequences of events. For example, a basic macro can allow a user a view from one camera for Ţve seconds and then switch to another camera for 10 seconds. The relays in the CM9760-KBD can be switched to either toggle or momentary. NOTE: When a relay is in toggle mode, a single key press will switch if either ON or OFF. In momentary mode, a relay will remain switched ON only while the appropriate key is held down. To conŢgure a relay: 1. Select from the Setup Mode Menu. 2. Select to go to the Advance Setup 2 Menu. Advance Setup 2 >Relay1 Toggle Mac1 0 Relay2 Toggle Mac2 0 SAVE TOGL MTRY MAC Figure 26. Advance Setup 2 Menu 3. Select or to go to Relay 1 or Relay 2. 4.Select or . 5. Select to go to Mac 1 or Mac 2. 6. Select and enter the macro number. Select . 7. Select and then . C540M-D (3/06) 21 ADJUSTING THE TIME OUT PERIOD Keyboard users can be timed out after periods of inactivity ranging from 1 to 254 minutes. To specify a time out period: 1. Select from the Setup Mode Menu. 2. Select or to go to the Advance Setup 3 Menu. Advance Setup 3 >Auto Logoff (min) off Auto Cam Rel(min) off 2015 Alm Rst(sec) off SAVE Figure 27. Advance Setup 3 Menu 3. Select and enter a duration between 2 minutes and 254 minutes. 4.Select . 5. Select and then . NOTE: The automatic log-off function can be disabled by entering 0, 1, or 255. SETTING THE CONTROL KEYS FUNCTIONS The control keys (F1-F24) can be assigned various functions, such as the enter function. 1. Select from the Setup Mode Menu. The Key DeŢne Menu appears on the LCD display. > NOT DEFINED KEY DEFINE NUM 0 NUM 1 PLEASE ENTER A KEY NUM 2 NUM 3 NUM 4 SAVE Figure 28. Key DeŢne Menu 2. Press the control key to which you want to assign a function. If the key has already been deŢned, its assigned function appears on the LCD display. If it is not deŢned, “Def = NOT DEFINED” appears on the LCD display. > NOT DEFINED KEY DEFINE NUM 0 NUM 1 Def = NOT DEFINED NUM 2 NUM 3 NUM 4 SAVE Figure 29. Key Not DeŢned 3. Select or to go to a desired function, and then select to choose that function. 22 C540M-D (3/06) BKSPACE KEY DEFINE ENTER MON Def = CAM MONx > CAM CAM GROUPx SAVE Figure 30. Key Functions 4.Select . 5. Select and then . You will be prompted to enter a number for many of the functions. Select , enter the number, and then select . DOWNLOADING KEYBOARD SETUPS The CM9760-KBD keyboard setup information can be downloaded and uploaded between keyboards, avoiding the need to conŢgure each keyboard individually in Setup Mode. Setup information that can be downloaded/uploaded includes control key functions, relay conŢgurations, direct camera control parameters, and up to ten user-deŢned icons. DOWNLOADING KEYBOARD TO KEYBOARD To download/upload setups between keyboards, the keyboards can be connected using COM 1 and/or COM 2 or through COM 3. The COM ports are under the keyboard. 1. Select from the Setup Mode Menu. The Keyboard Setup Menu appears on the LCD display. KEYBOARD SETUP >Target 9750/9760 Node Local Kbd# All/Any Figure 31. Keyboard Setup Menu 2. Select or to choose the COM port that is being used to download setup information. The example below shows KB-KB COM 1. The other options are KB-KB COM 2, KB-KB COM 3, and 9760MGR. KEYBOARD SETUP >Target KB-KB COM1 Node Kbd# Figure 32. Target Keyboard 3. Select to receive setup information from a connected keyboard. 4. Select to send setup information to a connected keyboard. The keyboard LCD indicates that it is going through the camera map settings. When it is Ţnished, “End of Tx” appears on the LCD display. C540M-D (3/06) 23 DOWNLOADING THROUGH THE CM9700 SYSTEMS Setups can be downloaded/uploaded using keyboards connected to CM9700 systems. You can upload the setup of a single keyboard to many other selected keyboards simultaneously. You can even upload the setup of a single keyboard to all keyboards in a CCTV installation. A CCTV installation can include multiple CM9700 systems. Each system is referred to as a node. The nodes are designated numbers from 1-24. To download/upload keyboard setups through the CM9700 system: 1. Select from the Setup Mode Menu. The Keyboard Setup Menu appears on the LCD display. The target should be 9750/9760. KEYBOARD SETUP >Target 9750/9760 Node Local Kbd# All/Any Figure 33. System Download/Upload 2. Select to go to Node and then select . 3. Enter a node number between 1-24, if necessary. Figure 34 shows Node 2. 4.Select . KEYBOARD SETUP Target 9750/9760 >Node 2 Kbd# All/Any Figure 34. Node Selection 5. Select to go to Kbd# and then select . 6. Enter a keyboard number between 1-96, or enter 0 to select all keyboards attached to selected node(s). 7.Select . 8. Select to receive setup information from a connected keyboard. 9. Select to send setup information to a connected keyboard. To upload a keyboard setup to all keyboards connected to a speciŢc system in a multiple-node CCTV installation, you must know the appropriate node number. If uploading to a speciŢc keyboard, you must know the keyboard number (1-96) and the node number. 24 C540M-D (3/06) UPLOADING TO THE MGR PROGRAM Setup information from a keyboard can be uploaded to a MGR program that is on a PC connected to a CC1. The MGR program must be online to receive the setup information. This information can be changed within the Windows environment and then sent back to the keyboard. To upload your keyboard setup: 1. Select from the Setup Mode Menu. 2. Select or to choose 9760MGR as the Target. 3. Select to send the keyboard setup information to the online MGR program. The keyboard LCD indicates that it is going through the camera map settings. When it is Ţnished, “End of Tx” appears on the LCD display. Refer to your MGR manual for information on editing your keyboard setup. C540M-D (3/06) 25 Operation ACTIVATING OPERATION MODE To use the keyboard, you must activate Operation Mode. 1. Select from the Setup Mode. The following message appears on the LCD display. SETUP MODE v8.24 TURN OFF SW’2, EXIT JSTK LCD ADV Figure 35. Setup Mode Exit Message 2. Set DIP Switch 2 OFF. 3. Select . The Log In Display appears on the LCD. SYSTEM 9700 v8.24 v7.00 Figure 36. Log In Display LOGGING IN To log in, enter your four-digit PIN from the Log In Display. As soon as you enter a number, PIN appears on the LCD display and four asterisks indicate the numbers of your PIN. The default login PIN is 1234 and can be changed only by the person responsible for programming or creating the conŢguration Ţles for the system. SYSTEM 9700 v8.24 PIN **** v7.00 Figure 37. PIN Number The following message appears on the LCD display when you enter a PIN successfully. Enter Monitor Num for Keyboard 1 Figure 38. Monitor Number 26 C540M-D (3/06) SELECTING MONITORS 1. Enter the monitor number for the keyboard. The number you enter appears next to the monitor icon. For example, enter monitor 1. If you attempt to access a monitor that does not exist, “Monitor Denied” appears on the LCD display. Enter Monitor Num for Keyboard 1 1 Figure 39. Monitor Number MON 2. Press . The Monitor Menu appears on the LCD display. 1 1 OVER RIDE Figure 40. Monitor Menu Figure 40 shows a 1 next to the monitor icon and a 1 next to the camera icon. That means that you will see video from camera 1 on monitor 1. MON 3. To go to monitor 2, enter 2 and press . 2 10 Figure 41. Monitor 2 Figure 41 shows a 2 next to the monitor icon on the Ţrst line and a 10 next to the camera icon. That means you will see video from camera 10 on monitor 2. 4. Select or to go through all of the available monitors. esc 5. Press or select to go to the Main Menu. 2 10 LOG PRST DEF GPI MAC OFF Figure 42. Main Menu MON You can also select a monitor from the Main Menu by entering a monitor number and then selecting or pressing . C540M-D (3/06) 27 MON You can also select a monitor if you have assigned the Enter function to one of the control keys. Press , enter a monitor number, and then press the control key that has been assigned the Enter function. SELECTING CAMERAS 1. Enter a camera number from the Main Menu. For example, enter camera 2. If you enter a camera number that does not exist, “Cam Not Present” appears on the LCD display. 1 1 2 LOG PRST DEF GPI MAC OFF Figure 43. Main Menu Camera Selection CAM 2. Select or press . The Camera Menu appears on the LCD display. 1 2 OVER RIDE Figure 44. Camera Menu 3. Select or to go through the available cameras. CAM You can also select a camera if you have assigned the Enter function to one of the control keys. Press , enter a camera number, and then press the control key that has been assigned the Enter function. NOTE: When going through the available cameras, you may see a camera input that has been deŢned as a multiplexer,VCR, or DVR. The control Fwd Bwd icons for those devices will appear on the LCD display. You must press or to get back to or . Refer to the CM9700-MGR Software Guide for information on how to add those devices. 28 C540M-D (3/06) LOCKING CAMERAS OR INPUT DEVICES To lock a camera to a monitor (or other output device): 1. Select the appropriate camera or input. 2.Select . 3. Select to unlock the camera. The example below shows that camera 3 is locked to monitor 1. If you try to access another camera, “Monitor Locked” appears on the LCD display. 1 3 OVER RIDE Figure 45. Camera Lock OVERRIDING CAMERA CONTROL If User A controls a camera and User B tries to access the same camera, “Busy Opr X” appears on the LCD display. If User B has equal or greater priority access, he can take control of the camera from User A by doing the following: 1. Select and hold from the Camera Menu. 2. Move the joystick or press a key on the camera control section of the keyboard. OVERRIDING CAMERA LOCKS If User A locks a camera to a monitor, User B can override User A if User B has greater priority access by selecting and at the same time. If User B does not have greater priority access, “Override Denied” appears on the LCD display. NOTE: When access is attempted by User B, “CAM LOCK OPERATOR #” appears on the LCD display. C540M-D (3/06) 29 Rcl In Near Open GROUP INPUT SELECTION The CM9760-KBD has 24 control keys that can be used for group input selections. For example, in a casino application, the control keys can be assigned the following group selections: • Black Jack • Roulette • Craps • Keno • Count Room • Baccarat Upon selection of any of the above to a single monitor, the keyboard defaults to the lowest logical input number within the selected group. The control keys can also be used to interface the user (either in groups or individually) with the following: • DVR – to provide remote control of DVR functions • VCR – to provide remote control of VCR functions • Multiplexer – to provide remote control of multichannel displays • Frame stores – to provide remote control of freeze and loop functions Upon selection of a DVR or VCR, the function keys are assigned appropriate control functions. The control keys can be allocated speciŢc area selections. SELECTING GROUP CAMERAS 1. Enter the group number. 2. Press the appropriate control key. For example, roulette. 3. Press to toggle to other associated cameras. Control of associated functions is now possible using the function keys. esc NOTE: The brings up the Main Menu. OPERATING PTZ CAMERAS The controls for PTZ cameras are located on the right side of the keyboard. If a PTZ camera is selected, “PTZ” appears on the top right corner of the LCD display. The proportional joystick allows variable speed control. It gives you full control over the pan and tilt movements, from minimum to maximum speed. Speed is proportional to the amount the joystick is moved away from the center location. T Press while moving the joystick to enable high speed operation. The joystick provides directional control only when a Ţxed speed PTZ camera is installed. The various functions of a PTZ camera can be controlled as follows: • Press to zoom in or out. • Press to focus near or far. • Press to open or close the iris. It is possible to operate the joystick simultaneously with a lens function. The iris open and close key functions only with the appropriate lens Ţtted. 30 C540M-D (3/06) Alt Out Far Close Advanced Operation PRESETS A preset camera position is a set of parameters that deŢne pan, tilt, zoom, and focus adjustments. There are several ways you can recall a preset camera position: • Manually using the keyboard • Automatically as the result of an alarm condition • From a macro command NOTE: Presets are possible only when receivers or pan/tilt units have preset capability. CREATING PRESETS There are 64 available presets. The following steps explain how to create a preset. 1. Select from the Main Menu. The DeŢne PIN Menu appears on the LCD display. Camera 22 in Figure 46 is a PTZ camera. Ptz 1 22 PIN PIN Figure 46. DeŢne PIN Menu 2. Enter your four-digit DeŢne PIN. The DeŢne Menu appears on the LCD display. Ptz 1 22 DEF VIDEO M O PRST R LOSS E Figure 47. DeŢne Menu NOTE: You can also change the LCD brightness from this menu. 3. Use the joystick and camera control keys to set up the camera preset required. 4. Select . The Preset Menu appears on the LCD display. Ptz 1 22 DEL PRST A B DEL PRST C Figure 48. Preset Menu 5. Enter an available preset number between 1-32 and 35-66. Numbers 33 and 34 are reserved for other functions. C540M-D (3/06) 31 Prst 6.Select . esc 7. Press to go back to the Main Menu. RECALLING PRESETS Follow these steps to recall a preset. 1. Enter the preset number. 2. Select or press . DELETING PRESETS Follow these steps to delete a preset. 1. Select from the Main Menu. 2. Select from the DeŢne Menu. 3. Enter the number of the preset you want to delete and select . CREATING A PRESET LABEL 1. Select from the Preset Menu. The Preset Label Menu appears on the LCD display. Ptz 1 22 DEF PRST _!”#$%&’()*+,-./ 0123456789;:<=>? @ABCDEFGHIJKLMNO PQRSTUVWXYZ[\]^_ Figure 49. Preset Label Menu 2. Move the joystick to a character and then select . You can enter a maximum of 20 characters. 3. Select or if you want to move to a speciŢc character and change it. 4. Select . The label appears on the LCD display. ASSIGNING A PRESET LABEL TO A PRESET LOCATION 1. Use the joystick to move the camera to the desired preset position. 2. Enter your preset number and then select . The label appears on the screen of the currently enabled monitor for that deŢned preset position. esc 3. Press to exit. 32 C540M-D (3/06) Lock RECALLING DEFINED PRESETS 1. From the Main Menu, enter the number of a deŢned preset and select . The camera moves to the preset position and the label appears on the monitor. 2. Repeat step 1 to recall other presets. PATTERNS A pattern is a viewable camera path with a deŢnite beginning and end. For example, you can set the camera to move repeatedly between two cars in a parking garage. You must create a pattern before the time-out clock expires. CREATING A PATTERN 1. Select from the Main Menu. The DeŢne Menu appears on the LCD display. Ptz 1 22 DEF VIDEO M O PRST R LOSS E Figure 50. DeŢne Menu 2. Select . The icon darkens. 3. Move the joystick to Point A and then select . 4. Move the joystick to Point B and then select . VIEWABLE AREA CAMERA JOYSTICK CONTROL Figure 51. Pattern DeŢnition NOTE: Pattern creation is the same regardless of which camera you use. The only difference is the time-out period. With a Spectra, you can create two 30-second patterns within the 60-second time-out period. C540M-D (3/06) 33 B A RECALLING A PATTERN 1. Select from the Main Menu. The Preset Menu appears on the LCD display. Ptz 1 22 PRST PRST Figure 52. Preset Menu 2.Select . NOTE: If you create two patterns within a time-out period, enter 1 and then select to run the Ţrst pattern. After you stop the Ţrst pattern, enter 2 and then select to run the second pattern. ZONES A zone is a user-deŢned space to which a label is attached and a camera is associated. The camera used at the time the zone boundaries are deŢned is associated with the zone. The zone label appears on the selected monitor after zone deŢnition if you move the camera within the deŢned zone. You can deŢne and associate up to eight zones with the same camera. A priority level (1-8, with 8 being the highest) is assigned to each zone. CREATING A ZONE 1. Move the joystick to the point where you want zone deŢnition to begin. Always move the joystick so that camera movement is from the left to the right. 2. Select from the Main Menu. The DeŢne Menu appears on the LCD display. Ptz 1 22 DEF M VIDEO O PRST R LOSS E Figure 53. DeŢne Menu 3. Select . The DeŢne Zone Menu appears on the LCD display. Ptz 1 22 DEF M O R E Figure 54. DeŢne Zone Menu 34 C540M-D (3/06) 4. Select . The Zone Label Menu appears on the LCD display. Ptz 1 22 DEF A B C Figure 55. Zone Label Menu 5. Select . The Character Menu appears on the LCD display. Ptz 1 22 DEF _!”#$%&’()*+,-./ 0123456789;:<=>? @ABCDEFGHIJKLMNO PQRSTUVWXYZ[\]^_ Figure 56. Character Menu 6. Move the joystick to a character and then select . You can enter a maximum of 20 characters. 7. Select or if you want to move to a speciŢc character and change it. 8. Select . The label appears on the Zone Label Menu. 9. Select . “Zone Number?” appears on the LCD display. 10. Enter a zone number (1-8) to assign a priority level to the zone. 11. Select again. The icon darkens signaling the start of zone creation. 12. Move the joystick to the point where you want zone deŢnition to end. Remember to move the joystick so that the camera pans only from the left to the right. 13. Select . Zone deŢnition is complete. esc 14. Press to go to the Main Menu. C540M-D (3/06) 35 B A CAMERA Figure 57. Basic Zone Creation When you move the camera through the zone area, the label appears on the selected monitor. Refer to Figure 57. 36 C540M-D (3/06) ZONE 1 NO ZONE LABEL ZONE LABEL APPEARS NO ZONE LABEL LABEL B PRIORITY 2 PARTIAL ZONE OVERLAP Partial zone overlap occurs when the end of one zone overlaps with the beginning of another zone. The zone with the highest priority level appears at all times. Refer to Figure 58. LABEL B LABEL A LABEL A BEGINS ENDS BEGINS LABEL B ENDS LABEL A PRIORITY 5 C540M-C-073 Figure 58. Partial Zone Overlap C540M-D (3/06) 37 LABEL B PRIORITY 2 EMBEDDED ZONES An embedded zone is a zone that is between two other zones. In Figure 59, Zone C is embedded between Zone A and Zone B. An embedded zone is not seen unless its priority level is higher than the priority level of the other zones. Since Zone C has a priority level of 6, portions of Zone A and Zone B are not seen. LABEL B LABEL A BEGINS ENDS LABEL C LABEL C BEGINS ENDS LABEL A BEGINS LABEL B ENDS LABEL C PRIORITY 6 LABEL A PRIORITY 5 LABEL A LABEL C LABEL B Figure 59. Embedded Zones TURNING ZONES ON AND OFF Follow these steps to turn zones on and off. 1. Select from the Main Menu. The Preset Menu appears on the LCD display. 2. Select . “ZONES OFF” or “ZONES ON” appears. 3. Select again to either turn the zone off or on. 38 C540M-D (3/06) ERASING ZONES To erase a zone, create a zone with no label (null zone) for each zone. The zone with no label overwrites the previous zone. DVR AND VCR CONTROL When a camera input is called up and appears on the LCD display, a CM9700MDD-EVS matrix digital decoder is connected to the sys- ™ tem. A user can view and control video on both the Endura and matrix systems. The DVR Control Menu appears on the LCD display. DVR 1 1001 DVR M O R E Figure 60. DVR Control Menu Refer to the CM9700MDD-EVS Installation/Operation manual for information on how to use the DVR controls. When a camera input is called up and appears on the LCD display, a VCR is connected to the system. The VCR Control Menu appears on the LCD display. VCR 1 1 VCR Figure 61. VCR Control Menu VCRs have to be modiŢed appropriately. For example, you may have to add hardware that provides alarm signal feedback. The VCRs must also interface with the CM9760-VCRC or CM9760-VCRC-P for the VCR control functions to appear on the keyboard’s LCD. Finally, the VCR video outputs are connected as inputs to the matrix system. Refer to the CM9760-VCRC and CM9760-VCRC-P Installation/Operation manuals for information on how to use the VCR controls. C540M-D (3/06) 39 GPI CONTROL A GPI can control up to eight relays. Relays are controlled from the auxiliary icons in the GPI Menu. GPI control is normally used for controlling peripheral devices connected to CM9760-REL units or for VCR control. Each relay unit has eight GPIs. The Ţrst relay unit has a GPI range of 1-8. Refer to Table A. Table A. GPI Control GPI RELAY CONTACTS 11 2345678 2910 11 12 13 14 15 16 31718192021222324 42526272829303132 53334353637383940 64142434445464748 74950515253545556 85758596061626364 ASSOCIATED AUX 1 2345678 To activate relay contact 4, for example, follow these steps: 1. Enter 1 from the Main Menu. GPI 1 is associated with relay contact 4. Refer to Table A. 2. Select . The GPI Menu appears on the LCD display. 1 1 GPI M O R 1 2 3 4 5 6 E Figure 62. GPI Menu 3.Select . 40 C540M-D (3/06) MUX CONTROL You can also control multiplexers with the CM9760-KBD keyboard. You can connect multiplexers to any input and conŢgure the MUX for operation within the CM9700 system using the CM9700-MGR. Refer to the CM9700-MGR Software Guide. To control a multiplexer: 1. Enter a MUX input number from the Main Menu. 2. Press . Each MUX input is associated with a camera input. Figure 63 shows MUX 1 being controlled. 1 1 Figure 63. MUX Control Menu 3. Select an icon. The icon functions are described in Table B. Table B. MUX Control Icons ICON FUNCTION Select this icon to bring up the MUX VCR control menu for operating the VCR. The menu appears only if a VCR for camera recording is connected to the MUX and conŢgured properly in the software. Select this icon to toggle the main monitor display between live inputs and playback from the VCR. Enter a camera number and select this icon. You can go through all 16 screens. Selecting this icon once enables 2X zoom and selecting it twice enables 4X zoom. Select this icon to display a picture in picture insert on the main monitor display. You can cycle through all 16 screens in the picture insert by entering a camera number and selecting . Select this icon to bring up 4 of the available 16 screens. You can cycle through all 16 screens, four at a time, by repeatedly selecting the icon. Select this icon to bring up 9 of the available 16 screens. Select this icon to view all 16 available screens at the same time on the main monitor. C540M-D (3/06) 41 MACROS A macro is a sequence of commands or steps. When you run a macro, the steps programmed into that macro are performed. Macros can be run manually or automatically. Automatic operation can be the result of alarms or the reaching of speciŢc times and dates. A macro will not run if it calls for the use of a camera or monitor which is already controlled by a user via a keyboard. To release control, go to a MON CAM non-PTZ camera or press or . LOADING MACROS To load a macro: 1. Go to the Main Menu and then select . The Macro Menu appears on the LCD display. 1 1 MAC DEL Figure 64. Macro Menu Mac 2. Enter the macro number and then press . 3. Select or to display all running macros. When a macro completes all its steps, it stops and will only run again if restarted. If the macro is continuous, it will run until cleared or stopped. If a valid macro number is entered, “Macro n” appears and the macro runs. If an invalid macro number is entered, “Macro not present” appears. If the user has insufŢcient access rights, “Access denied” appears. PAUSING A MACRO To pause a macro: Mac 1. Select from the Main Menu to display the running macro number. 2. Select or to go through the macros that have been loaded. 3. Select to pause the macro. 4.Select . NOTE: To restart a macro, select . DELETING A MACRO To delete a macro: 1. From the Main Menu, enter the number of the macro you want to delete and then select . 2. Select to delete the macro. 42 C540M-D (3/06) CREATING A TEMPORARY MACRO The create a temporary macro: 1. Select from the Main Menu. The DeŢne Menu appears on the LCD display. Ptz 1 22 DEF VIDEO M O PRST R LOSS E Figure 65. DeŢne Menu 2. Enter a macro number and select . The number appears next to and a 1/1 appears above the Exit icon. This means you are in Step 1 of the temporary macro, sub-step 1. 1 DWL 1 1/ 1 DEF 4 DWL DEL Figure 66. Macro DeŢne Menu NOTE: “Macro DeŢned” appears if the macro is already used. CAM 3. Enter the number of the camera you want to be Ţrst in the sequence and then press . The 1 / 1 changes to 1 / 2 to indicate sub-step 2. 8 1 DWL 1 1/ 2 DEF 4 DWL DEL Figure 67. Macro DeŢne Menu 2 4. Enter a dwell time (in seconds) and then select . The number appears next to . 8 1 DWL DWL 20 DEF 4 DWL DEL Figure 68. Macro DeŢne Menu 3 C540M-D (3/06) 43 5. Select . 1 / 2 changes to 2 / 2 to indicate movement to Step 2 of the temporary macro. 1 DWL DWL 20 2/ 2 DEF 4 DWL DEL Figure 69. Temporary Macro Step 2 6. Repeat Steps 3-5 until you have conŢgured the last camera you want in the sequence. 7. Select or to go through the steps of the sequence or select to insert a new step between two existing steps. 8. Select . The temporary macro starts until you pause it or delete it. Once uploaded you cannot recall the macro to edit it. NOTE: The macro will be deleted if you recycle power on the keyboard or reset the CC1. SETTING THE TIME AND DATE You can change the date and time from the CM9760-KBD. CAUTION: Changing the time/date on any CM9760-KBD will change the time for the entire system. 1. Select from the Main Menu. 2. Select . The following appears on the LCD display. 11 DEF Date:_m/dd/yy VIDEO M O PRST MAC R E LOSS Figure 70. Time and Date Display 3. Enter the month, day, and year (xx/xx/xx). 4. Select . The following appears on the LCD display. 11 DEF Time:_h/mm/ss VIDEO M O PRST MAC R E LOSS Figure 71. Hours and Minutes Display 5. Enter the hour, minutes, and seconds (xx/xx/xx) in the 24-hour format. For example, enter 8:00 p.m. as 20/00/00. 6. Select and then . The time and date will be updated on all equipment in the system. 44 C540M-D (3/06) VIDEO LOSS The video loss function allows you to disable a camera that has malfunctioned. 1. Select from the Main Menu. 2. Select . The Video Loss Menu appears on the LCD display. 11 DEF 1 VIDEO LOSS Figure 72. Video Loss Menu 3. Enter the camera number and select . 4. Select to disable the camera. NOTE: To enable the camera, select . means that the camera is disabled. ALARMS Alarms can be armed or disarmed from the CM9760-KBD. You must arm an alarm if you want to be notiŢed that it has triggered. Alarms have to be rearmed if the keyboard is turned off. Macros are normally used to arm alarms. ARMING ALARMS A list of the logical alarm numbers should be available from your manager or security supervisor. To arm an alarm: 1. From the Main Menu, enter the logical number of the required alarm and select . The Alarm Menu appears on the LCD display. Figure 73 shows alarm number 1. 11 1 ARM DIS’ Figure 73. Alarm Menu NOTE: “Alarm denied” appears if access to the alarm has been denied to the user and “Alarm not present” appears if the alarm has not been programmed into the system. 2. Select . The icon darkens meaning that the alarm is armed. You will be notiŢed if it is triggered. C540M-D (3/06) 45 DISARMING ALARMS To disarm an alarm: 1. From the Main Menu, enter the logical number of the required alarm and select . 2. Select . The icon lightens meaning that the alarm is disarmed. NOTE: While in the Alarm Menu, you can use or to go through all of the alarms. This is the easiest way to Ţnd out the status (armed or disarmed) of each alarm. RESETTING ALARMS When an alarm is triggered, you will see [alarm] ţashing plus an alarm number on the LCD display. The alarm volume can be raised or lowered by using the volume control on the bottom of the keyboard. To reset a triggered alarm: 1. Select from the Main Menu. The triggered alarm appears on line 3 on the LCD display. Refer to Figure 74. 11 1 1 ARM R R A DIS’ Figure 74. Triggered Alarm Menu 2. Select the appropriate icon to disarm the alarm, mute the alarm, pause the alarm, or reset the alarm. NOTE: Select to reset all triggered alarms. LOGGING OUT To log out from Operation Mode: esc 1. Press . The Main Menu appears on the LCD display. 2. Select . The following appears on the LCD display. 1 1 Are you sure logoff? YES NO Figure 75. Verify Logoff 3.Select . NOTE: You can also select monitor 0 to log off from the Main Menu. 46 C540M-D (3/06) Service DIAGNOSTICS MODE This mode allows you to test the LCD display, the keys, and the DIP switches. To activate this mode, set DIP Switch 1 ON. The Diagnostic Mode Menu appears on the LCD display. DIAGNOSTIC MODE v8.24 Figure 76. Diagnostic Mode Menu NOTE: Do not select . The serial port test is for factory use only. TESTING THE DISPLAY Select from the Diagnostic Mode Menu. The LCD Test Menu appears. LCD TEST G0 G1 G2 TO Figure 77. LCD Test Menu 1. Select to test Graphic Page 0. 2. Select to test Graphic Page 1. 3. Select to test Graphic Page 2. 4. Select to test Text Page 0. 5.Select . C540M-D (3/06) 47 TESTING THE KEYS 1. Select from the Diagnostic Mode Menu. The Keyboard Test Display appears. KEYBOARD TEST v8.24 PLEASE ENTER A KEY Joystick Position - (513,518) Figure 78. Keyboard Test Display 2. Press each key and make sure the display shows the correct key. 3.Select . NOTE: When testing the keyboard, pressing the control keys (F1-F24) causes their assigned functions to be displayed. TESTING THE DIP SWITCH 1. Select from the Diagnostic Mode Menu. The DIP Switch Test Display appears. DIPSWITCH TEST 00000001 Figure 79. DIP Switch Test Display 2. Beginning with switch 2, set each switch ON while looking at the display. NOTE: When switched ON, functioning switches will change the corresponding displayed 0 to a 1. For example, when switch 2 is ON, the display should read 00000011. 48 C540M-D (3/06) SpeciŢcations ELECTRICAL Input Voltage 100-240 VAC, 50/60 Hz Power Consumption 10 watts Communications RS-422, full duplex Operating Distance (For direct control operation) 4,000 feet (1,219 m) on 24 AWG wire Connectors Two 8-pin RJ-45 connectors (female) Both RS-422 serial ports One 4-pin RJ-45 connector (female) RS-232 serial port Two 6-pin RJ-45 connectors (female) One PC bus port for future expansion One relay port MECHANICAL Joystick Proportional Display Four-line backlit LCD for programming and control LCD Menu Display Six multipurpose function keys for LCD menu selection Numerical Input Ten-key numeric keypad with two additional keys for camera and monitor selection Control Keys Twenty-four user-deŢnable control keys Function Controls Six keys for function controls Lens Control Three keys for zoom, iris and focus control GENERAL Operating Temperature 32° to 120°F (0° to 49°C) Dimensions CM9760-KBD 3.30" H x 15.53" W x 7.80" D (8.38 x 39.45 x 19.81 cm) CM9760-KBR 7.00" H x 19.00" W x 1.75" D (17.78 x 48.26 x 4.45 cm) Weight CM9760-KBD 4.6 lb (2.09 kg) CM9760-KBR 6.4 lb (5.00 kg) C540M-D (3/06) 49 50 C540M-D (3/06) PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or workmanship for a period of one year after the date of shipment. (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number • Five years on FR/FT/FS Series Ţber optic products and TW3000 Series unshielded twisted pair transmission products. 3. Details of the defect or problem ® • Three years on Genex Series products (multiplexers, server, and keyboard). If there is a dispute regarding the warranty of a product which does not fall under the ® • Three years on Camclosure and Ţxed camera models, except the CC3701H-2, warranty conditions stated above, please include a written explanation with the product CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, when returned. which have a Ţve-year warranty. Method of return shipment shall be the same or equal to the method by which the item was • Three years on PMCL200/300/400 Series LCD monitors. received by Pelco. •Two years on standard motorized or Ţxed focal length lenses. ® •Two years on Legacy , CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series RETURNS Ţxed dome products. In order to expedite parts returned to the factory for repair or credit, please call the factory at ® ® ™ •Two years on Spectra , Esprit , ExSite , and PS20 scanners, including when used in (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned continuous motion applications. for credit, and RA number if returned for repair). ® •Two years on Esprit and WW5700 Series window wiper (excluding wiper blades). All merchandise returned for credit may be subject to a 20% restocking and refurbishing ® •Two years (except lamp and color wheel) on Digital Light Processing (DLP ) displays. charge. The lamp and color wheel will be covered for a period of 90 days. The air Ţlter is not covered under warranty. Goods returned for repair or credit should be clearly identiŢed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. • Eighteen months on DX Series digital video recorders, NVR300 Series network video ™ recorders, and Endura Series distributed network-based video products. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: • One year (except video heads) on video cassette recorders (VCRs). Video heads will be Service Department covered for a period of six months. Pelco • Six months on all pan and tilts, scanners or preset lenses used in continuous motion 3500 Pelco Way applications (that is, preset scan, tour and auto scan modes). Clovis, CA 93612-5699 Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, instructed to return goods to the USA, you may do one of the following: California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from 3500 Pelco Way the speciŢc use or application made of the Products. Pelco’s liability for any claim, whether Clovis, CA 93612-5699 USA based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: such Products. In no event will Pelco be liable for any special, incidental or consequential Pelco c/o Expeditors damages (including loss of use, loss of proŢt and claims of third parties) however caused, 473 Eccles Avenue whether by the negligence of Pelco or otherwise. South San Francisco, CA 94080 USA Phone: 650-737-1700 The above warranty provides the Dealer with speciŢc legal rights. The Dealer may also have Fax: 650-737-0933 additional rights, which are subject to variation from state to state. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment. REVISION HISTORY Manual # Date Comments C540M 6/97 Original version. 3/98 Included KBR and expanded direct control instructions. Changed manual pagination. Added Section 1.2, CertiŢcations. 6/98 Added Section 1.2, CertiŢcations. C540M-A 8/99 Updated manual to correspond to version 4.0 of KBD software. C540M-B 1/03 Revised Section 3.2.5, Calibrating the Joystick, per ECO 02-8581 and ECO 02-8394. C540M-C 10/05 Manual completely revised and updated. Added Automatic Joystick Calibration. Added DVR control information. C540M-D 3/06 Revised Models section. Revised input voltage and power consumption. Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2006, Pelco. All rights reserved. Endura and ExSite are trademarks of Pelco. DLP is a trademark of Texas Instruments, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |