PC ENGINES cf2g

PC Engines GmbH CF adapter · Install the jumper to run as master device, or IDE to CompactFlash adapter remove for slave (CFDISK.1x models only). The IDE to CompactFlash adapter enables OEMs · CompactFlash cards sold for digital camera use to replace hard disk drives with economical, rugged sometimes have strange partition sectors, and CompactFlash cards. may require rewriting (FDISK /MBR) to make Benefits them bootable. · To most BIOSes and operating systems, the · Low power (less than 0.5W) CompactFlash card will look just like an IDE · Fast startup time – no spinup. hard disk drive. · Fast read access time. Power · Higher transfer rate than DOC. The adapter is passive, and does not draw any · Not sensitive to shock and vibration. power by itself. Typical CompactFlash cards draw · Suitable for extended temperature range less than 100mA from the +5V rail. +12V is not (depending on card) needed. · Small capacity cards are less expensive than hard Compliance disk drives. Cards are available at competitive prices from many suppliers. PCB is rated UL 94V-0. The adapter is designed for · Compatible with IDE hard drives, no special use inside a chassis. Power to the CompactFlash drivers required. card is not fused. As EMI depends greatly on enclosure design, the adapter has not been tested · No acoustic noise. for EMI or susceptibility. Applications Custom designs · Network appliances such as firewalls or routers. Special configurations and custom designs are · Industrial control, robotics available – please ask for a quotation. · Point of Sales PC Engines GmbH · Functional test fixtures for system boards or Germaniastr. 68 adapter cards (faster boot time, no spinup delay) CH-8006 Zürich Switzerland Easy to use +41 43 268 9817 · Just connect power and IDE cable, and plug in +41 44 355 3053 FAX card. pdornier@pcengines.ch · Due to limitations in the CompactFlash spec and operating system software, hot insertion is not supported. Rev. 9 (C)2005 PC Engines GmbH. All rights reserved. PC Engines is a trademark of PC Engines GmbH. Other marks are the property of their respective owners. CFDISK.1x dimensions This is the 40 pin IDE version, designed for use with standard PC system boards. This version is available with hard disk (large) or floppy disk (small) power connectors. The CF connector supports type I (regular CompactFlash) and type II (e.g. IBM Microdrive) cards. This board can be configured for master / slave – install jumper for master, remove jumper for slave. CFDISK.1C can be configured with ejector on request (type I cards only). A dual stacked version (master + slave) is also available (special order only). Change history: CFDISK.1E Add support for IDE DMA. CFDISK.1D Use low profile CF header for lower cost CFDISK.1C Made in Taiwan, all ceramic bypass capacitors CFDISK.1B Assembled in USA, PTH electrolytic bypass capacitors CFDISK.1A Assembled in USA, SMT electrolytic bypass capacitors All dimensions in mils (0.001 inches). CFDISK.2A - 2D dimensions (phased out – special order only) This is the 44 pin IDE version, designed for use with embedded PC system boards. The board is designed to have the same outline and pinout as a 2.5”hard disk drive, but will not match the vertical profile of modern 2.5” drives. The 44 pin connector includes power, there is no separate power connector. The CF connector supports type I and type II cards. CFDISK.2E / 2F / 2G dimensions This version has the same outline, but is designed to match the vertical profile of 2.5” drives. This board is mounted through threaded stand-offs from the bottom side. The 44 pin connector includes power, there is no separate power connector. The CF connector supports type I and type II cards. Change history: CFDISK.2G Change to CSEL cable select instead of hard-wired master / slave. CFDISK.2F Added IDE DMA support. CFDISK.2E Straddle mount connector, threaded standoffs CFDISK.2D Made in Taiwan CFDISK.2C Assembled in USA, all ceramic bypass capacitors, delete master / slave jumper, change CF header CFDISK.2B Assembled in USA, no stuff redundant bypass capacitors, change CF header CFDISK.2A Assembled in USA, SMT electrolytic bypass capacitors CFDISK.5x dimensions This version is designed to plug directly onto an IDE header, using a right angle female header (adapter at a right angle to the PCB). Power is supplied by a floppy power connector. The CF card extends beyond the PCB, so this solution is not suitable for 1U chassis. Not recommend for high vibration environments. No master / slave selection. This board can also be ordered with a straight 40 pin header (CFDISK.5GS) In this configuration, the adapter is coplanar (parallel) with the system board, with the CF header facing down. Change history: CFDISK.5H Added IDE DMA support. CFDISK.5G Change of CF header for lower cost CFDISK.5F Special version with 180 degree rotated data connector (special order) CFDISK.5D Made in Taiwan CFDISK.5C Assembled in USA, all ceramic bypass capacitors, change CF header CFDISK.5B Assembled in USA, change electrolytic cap to SMT, turn IDE connector around, use keyed connector CFDISK.5A Assembled in USA, non-keyed connector (different orientation)